wl-hdd with a php web server?

[youngprodigys]

Right, had a few problems with Oleg's 1.9.2.7-4 mod.

My problem - it didnt bloomin work.
i have followed it to a tee 5 times,

it just wont mount my hdd or start the php web server.

i can install the software needed and its all good up to there and i can mod the thttpd.conf fiile
the dropbear bit goes well too.
But now heres where it all goes pete tong - "making the webserver and build-in ssh server startup at boot,ans making them accessible from wan"

i change the "mount /dev/discs/disc0/part1 /opt" and correct it to match mine
"mount /dev/discs/disc0/part5 /opt " and then the swapon to part6

Now i flashfs save,commit,enable and reboot - the swap partition is working but my webserver isnt and i have to mount part5 myself on reboot - what am i doing wrong?

if any1 has go this working on there wl-hdd and has created a firmware?

it would be good to see my wl-hdd working as a php webserver because then i can use it.

Anyone got any ideas?

Thanks - Kieran

[macsat]

Hi

Have you tried to just run :


/opt/etc/init.d/S80thttpd

after you router has rebooted ?

[youngprodigys]

ive tryed lots of things to remember, il give this a go, going to work now though so il let you know about 6pm
Thanks
Youngprodigys

[youngprodigys]

Right, i tried what you said and heres the outcome - as i can see the device IS mounted and so is the swap. but no webserver and no ftp - as soon as i flashfs i lost the ability to ftp.



(none) login: admin
Password:
[admin@(none) root]$ df
Filesystem 1k-blocks Used Available Use% Mounted on
/dev/root 2944 2944 0 100% /
/dev/discs/disc0/part5 10854013 53714 10236821 1% /opt
[admin@(none) root]$ free
total used free shared buffers
Mem: 13948 12816 1132 0 1080
Swap: 506012 1148 504864
Total: 519960 13964 505996
[admin@(none) root]$ /opt/etc/init.d/s80thttpd
-sh: /opt/etc/init.d/s80thttpd: not found
[admin@(none) root]$

ignor the PHP on the top box - just didnt know how to put a box round it.
any ideas any1? i followed the instructions as i should have

Thanks
Youngprodigys

[macsat]

The command should be :


/opt/etc/init.d/S80thttpd start

Case DOES matter....this will not work :


/opt/etc/init.d/s80thttpd start

And you did use lower-case for your 'S' in 'S80thttpd'

[youngprodigys]

Hi, thanks for the quick reply, i did as you said and got the following


(none) login: admin
Password:
[admin@(none) root]$ df
Filesystem 1k-blocks Used Available Use% Mounted on
/dev/root 2944 2944 0 100% /
/dev/discs/disc0/part5 10854013 53714 10236821 1% /opt
[admin@(none) root]$ /opt/etc/init.d/S80thttpd start
Warning : /opt/var/run/thttpd.pid still present. Unclean shutdown ?
Starting thttpd... done
[admin@(none) root]$

so does this mean it is working? i try to type the web address http://192.168.123.99/index.htm - and get nothing.

could it be a problem with the setup of the firewall - im going to re do this now.

+ why can i not get ftp? whats the command to set it running again?

Thanks
Youngprodigys

[macsat]

For accessing your new www server from your LAN, using the LAN ip address, you need to connect to port 81...like :

http://my.router:81

Try to just click the above link, and see if it works...

ftp depends on your setup..

Did you mount your ONLY attached storage on /opt ??

Then the built-in stupid-ftpd server will not start up. That one expects something to be mounted on /tmp/harddisk

I can only recommend you trying to get vsftpd running....there is a guide for that on www.macsat.com/wlguide.

[youngprodigys]

You are a legend - running it on port :81 it works, im setting everything up to suit

Thanks

+ it is my only attached storage - im starting on your other guide, il let you know

+ 1 more thing - you are a true pioneer for your guides

well done to you!

[youngprodigys]

at the end of my rag with this now, its b*ll*x

I have my webserver running - how the hell do i add file to it?

run ftp? - cant, screws it up, now im left with your vsftpd server running - kicks the webserver off and changes the mount to /tmp/harddisk

im only following your instructions - to the word almost!

any1 else got this problem?