Bekijk de volledige versie : New Asus RT-N13U Router

16-08-2009, 09:25
This is the new router RT-N13U (http://www.asus.com/product.aspx?P_ID=O8alKdC7I2FAs2FQ&templete=2) from ASUS, as I can understand, successor of Wl520g series.

Here the additional specs:

CPU: Ralink RT3052F 384Mhz (MIPS 24K)
RAM: 32Mb (2 x 16Mb)
ROM: 4Mb
USB: 1
WLAN: Dual Radio N
OS: Linux version 2.6.21

Bootloader is U-boot, serial console (see pinout on second picture) has 57600 baudrate.

Internal photos:

20-08-2009, 20:59
looks like a nice mid-range router with lots of options:)

too bad there is a modem inside... I already have one:p

13-10-2009, 08:49
I've increased the speed of pptp connection up to 2,5 times theoretically.
Firmware with accelerated pptp is based on the latest stable gpl sources from asus site, and we need volunteers to test it at high traffic load.

FW should be flashed via web-interface, as usual, neither reconfiguration not options changes are required after switching from original FW.
If something goes wrong, you can fallback on the last official from asus with flashing back it via web-interface.

13-10-2009, 08:58
too bad there is a modem inside... I already have one:pThere's no any modem inside, it's ethernet router

17-10-2009, 16:42
What about USB speed (samba, ftp, www)? Is it better then wl-500 series?
In my country is avaible to buy for 70 (105$).

17-10-2009, 17:22
will check tomorrow, should be much more better than with wl500g

18-10-2009, 22:22

# cat /proc/cpuinfo
system type : Ralink SoC
processor : 0
cpu model : MIPS 24K V4.12
BogoMIPS : 255.48
wait instruction : yes
microsecond timers : yes
tlb_entries : 32
extra interrupt vector : yes
hardware watchpoint : yes
ASEs implemented : mips16 dsp
VCED exceptions : not available
VCEI exceptions : not available


# free
total used free shared buffers
Mem: 28884 19012 9872 0 0
Swap: 65528 2060 63468
Total: 94412 21072 73340

process info

# ps
1 admin 2568 S /init
2 admin 0 RWN [ksoftirqd/0]
3 admin 0 SW< [events/0]
4 admin 0 SW< [khelper]
5 admin 0 SW< [kthread]
30 admin 0 SW< [kblockd/0]
33 admin 0 SW< [khubd]
45 admin 0 SW< [kswapd0]
46 admin 0 SW [pdflush]
47 admin 0 SW [pdflush]
48 admin 0 SW< [aio/0]
182 admin 0 SW [mtdblockd]
240 admin 0 SW< [dwc_otg]
253 admin 0 SW< [scsi_eh_0]
254 admin 0 SW< [usb-storage]
264 admin 0 SW [RtmpWscTask]
286 admin 2260 S /usr/sbin/pppd file /tmp/ppp/options.wan0
311 admin 3088 S httpd eth2.2
342 admin 2508 S usdsvr_broadcast
343 admin 2508 S usdsvr_unicast
355 admin 1196 S lld2d br0
356 admin 1452 S /usr/sbin/wanduck
384 admin 1772 S networkmap
385 admin 1760 S /bin/sh
482 admin 1088 S dproxy -c /tmp/dproxy.conf
484 admin 2540 S ntp
490 admin 2540 S ots
492 admin 1552 S lpd
506 admin 2624 S upnpd -f ppp0 br0
507 admin 2540 S watchdog
508 admin 2624 S upnpd -f ppp0 br0
509 admin 2624 S upnpd -f ppp0 br0
511 admin 2624 S upnpd -f ppp0 br0
512 admin 1764 S /usr/sbin/infosvr br0
513 admin 1752 S /sbin/syslogd -m 0 -t RFT-5RFTDST -O /tmp/syslog.log
515 admin 1752 S /sbin/klogd
517 admin 2624 S upnpd -f ppp0 br0
518 admin 2624 S upnpd -f ppp0 br0
520 admin 2624 S upnpd -f ppp0 br0
521 admin 2624 S upnpd -f ppp0 br0
523 admin 2540 S ntp
527 admin 2624 S upnpd -f ppp0 br0
528 admin 2624 S upnpd -f ppp0 br0
532 admin 1868 S vsftpd
550 admin 1756 S telnetd

interrupts usage

# cat /proc/interrupts
3: 83161 Surfboard eth2
4: 22912 Surfboard ra0
5: 287019 Surfboard timer
6: 0 Surfboard ralink_gpio
12: 826 Surfboard serial
17: 1 Surfboard Ralink_ESW
18: 9390429 Surfboard dwc_otg, dwc_otg_hcd:usb1

usbflash read speed

# hdparm -tT /dev/sda

Timing buffer-cache reads: 82 MB in 0.51 seconds = 162777 kB/s
Timing buffered disk reads: 23 MB in 3.10 seconds = 7587 kB/s

usbflash read speed via ftp

colinux:~# LC_ALL=C wget -v
Length: 104857600 (100M)
100%[==========>] 104,857,600 4.01M/s in 25s
2009-10-19 02:54:09 (3.97 MB/s) - `test.100mb' saved [104857600]

colinux:~# LC_ALL=C wget -v
Length: 209715200 (200M)
100%[==========>] 209,715,200 4.48M/s in 49s
2009-10-19 02:55:56 (4.10 MB/s) - `test.200mb' saved [209715200]

04-11-2009, 09:56
I have some questions:
does it have dropbear integrated?
can i install ipkg packages like transmission ?
what is the wireless N speed ?


04-11-2009, 10:49
I have some questions:
does it have dropbear integrated?
can i install ipkg packages like transmission ?

FW by link above, it is stock firmware with upgraded PPTP only.
So, no any custom features yet, only PPTP speedup.

06-02-2010, 04:25
I managed to compile the rtn13u firmware using the GPL sources provided by Asus (a miracle since asus tools had always failed to compile correctly for me before). Before compilation I modified busybox to include wget and chroot applets. Then I moved the rtn13u root file system of the newly compiled firmware to another mipsel device. To test the rtn13u root file system, I chrooted into it, and chroot worked.

I also compiled dropbear using buildroot-2009.02-rc1 (http://buildroot.uclibc.org/downloads/buildroot-2009.02-rc1.tar.bz2), moved it to the rtn13u root file system and tried to run it in the rtn13u chroot. dropbear ran fine, which means binaries compiled by this buildroot version can run on the rtn13u. So I decided to include dropbear in the firmware and generated another one.

Now, the flashing part. Using the web interface, I flashed my firmware with dropbear. It flashed without any complaint, but after reboot it went into recovery mode. I checked the firmware size, it was nearly 4MB. Too big. So I flashed the stock firmware on it to try bringing it back to normal. Didn't work, still in recovery mode. Time to hook up the serial console!

Using the serial pinout shown in this thread and the baudrate I got serial access fine and did a tftp flash of the stock firmware. The same thing happened: recovery mode after flashing.

So I had a brilliant idea (at the time :D): clear the flash and flash again. Too bad I erased everything, including u-boot. Now only the power LED stays on. Yes, I have a brick :D.

I also discovered that while inside the rtn13u chroot, I could do another chroot into the Oleg file system, set up Optware and ran Optware binaries like transmission and dropbear OK. And while having a brief play with the physical rtn13u before I bricked it, I found out that as soon as I connected a hard drive, I got kicked out of telnet. Sneaky tactic by Asus eh? I think we can get around this by using utelnetd instead of the busybox telnetd.

06-03-2010, 11:48

06-03-2010, 12:24
You have to put router in TFTP recovery mode by lower button. Desktop IP address must be set to for this operation.

Sorry, don't know anything about dd-wrt.

14-06-2010, 21:18
dd-wrt firmware for RT-N13U now ready for testing http://www.dd-wrt.com/phpBB2/viewtopic.php?t=61734&postdays=0&postorder=asc&start=135

Everything critical working fine for me.

USB auto mount not working

TX Power not working correctly

NG Mixed mode works only as G

QoS who cares :-)

19-06-2010, 16:22
Asus RT-N13U Rev.B1 (8MB Flash/64MB RAM) - 802.11n/300 Mbps & 3.5g

3G USB Adapter Support List: http://event.asus.com/2009/networks/3gsupport/ :)

http://wl500g.info/showthread.php?p=201887#post201887 ;)

06-10-2010, 18:11
Almost identical to original HW rev. Twice the ram size and an MX29LV640EBTI-70 flash on board. Circuit board is identical.

16-01-2011, 00:11
Hey everyone,

I know this isn't the right forum, but I can't find one with nearly as much knowledge as this, for what I'm trying to do. I have an Asus RT-N13U which I am trying to enable USB modem support for, and can't figure out how to compile custom firmware. Rev B supports this feature, but has 8MB of flash vice 4MB, so the firmware can't be flashed. The chipsets are identical, so I believe I could just import the necessary files to the Rev A firmware and use it, but I don't know how to do that, and was hoping some of you with more familiarity with Linux and firmware compiling can help me out. Thanks in advance.

Wahroonga Farm
19-03-2011, 23:58
Hi all,

New here. :)

I am seeking to modify the n13u to accept an external antenna.

Couple of questions:

1. How to open the n13u case? :)

2. Is there a u.fl connector on board (see circled area)?

3. Perhaps a simple mini coax to board solder job in the area identified in the pic below?

Any ideas suggestions great fully accepted.

Note: The task is to install a solar powered remote 3g receiver <-> wifi transponder (n13u) in a location where 3g reception is available; with a 1km wifi link back to the home.

09-08-2011, 13:46
Please tell me the name of chip U504?
Given device with a burned item.

Wahroonga Farm
09-08-2011, 22:12
Hi all,

Couple of questions:

1. How to open the n13u case? :)

2. Is there a u.fl connector on board (see circled area)?

3. Perhaps a simple mini coax to board solder job in the area identified in the pic below?

1. It's tricky. The key to opening is at the top of the case where you need a thin probe to release the plastic internal catches. Remove the label at the base to reveal a few case screws.

2. No this is a test point only

3. I did not go a head with a mod, but cutting tracks near the antenna would provide a solution.