Firmware v1.9.2.7 CR3c [Oleg] [Archive]

Bekijk de volledige versie : Firmware v1.9.2.7 CR3c [Oleg]

Oleg

31-01-2005, 21:24

I've made new firmware available for download (http://oleg.wl500g.info/1.9.2.7-3c/). Check this page (http://oleg.wl500g.info/) for other info.

First publically available firmware with LZMA compresses squashfs. 7zip SDK is used
Fully functional MPPE over PPTP connections, updated pptp-linux to 1.5.0 (thanks to Posader for testing and suggestions)
Tx-Only Idle option for PPTP
Added an ability to specify custom pppd options (nomppe-stateful is usefull with MPPE)
Ntp synch interval is now configurable
Added an ability to view syslog messages in the AP mode, added Syslog/NTP configuration page (use IP addresses, names ae not supported yet)
New busybox applets (halt, mkswap, swaponoff, crontab)
Fixed stupid-ftpd bug, causing incorrect rights specified for newely created files, as well as file is now truncated before upload
Added support for WL-HDD rootfs (thanks to Ulrich for initial patch)
Stupid-ftp should now work with some linux ftp clients (thanks to Ulrich for patch)

int

31-01-2005, 21:30

I will test fw now!!

1 hours, 5 minutes, 13 seconds since boot, and works well!

(not now!)

Oleg

31-01-2005, 21:43

I will test fw now!!

1 minutes, 17 seconds since boot and works well!
int, nothing changed compared to 3b, probably reboot problem is still there...

int

31-01-2005, 23:07

Yes reset issue are present!!

In this fw, after reboot issue i can't connect to Internet!!!

Oleg, can you make a fw that store the syslog! to see if any error display before reset?

Colonizer

31-01-2005, 23:26

Hi,

I am having big Problems with this new FW. I can not connect to my Ebay account, or to a hotmail account.

With the regular Asus 1.9.2.7 i do not have this problems, bus the router does not reconnect after the ISP disconnects me.

Although i tried to flash the old 1.7 FW (including Hardwarereset) the Router displays 1.9.2.7, thats odd, because i had your CR3c before..

Any idea how to get back to the old FW?

btw i do not use WLAN right now

jbrbv

31-01-2005, 23:38

Is WDS broken? With 3b it worked. With 3c it ain't.

Antiloop

01-02-2005, 00:44

Is WDS broken? With 3b it worked. With 3c it ain't.
wds with wpa-psk or wep? (wpa-psk was already broken in 1.9.2.7)

Oleg

01-02-2005, 09:34

I am having big Problems with this new FW. I can not connect to my Ebay account, or to a hotmail account.

Please specify your connection type. Is it PPTP? DHCP ?

Although i tried to flash the old 1.7 FW (including Hardwarereset) the Router displays 1.9.2.7, thats odd, because i had your CR3c before..

CR3c should display 1.9.2.7-3c in the "Firmware Release" field, stock firmware should not display Release field at all. If you do not have Release field - this is not a custom firmware. Check this picture http://oleg.wl500g.info/1.9.2.7-3c/1.9.2.7-3c.jpg

Oleg

01-02-2005, 10:24

Oleg, can you make a fw that store the syslog! to see if any error display before reset?
There is no way to do so. Instead you could install syslog capable server on your PC and then specify it's address for the wl500g.

Holli

01-02-2005, 10:51

What can I do with the halt command?
When I`ll turn off the AP, I cut the power source!

int

01-02-2005, 11:39

by using a syslog server:

I dont detected any error, but i think the error about reset issue are in:

DHCPINFORM(br0) 192.168.1.11 00:04:e2:aa:b4:d0
2005-02-01 11:23:21 Daemon.Info 192.168.1.1 dnsmasq[49]: DHCPACK(br0) 192.168.1.11 00:04:e2:aa:b4:d0 int

are to many msg...

The log show also the auto-connection to internet issue after reset issue..

short syslog:

...
DHCPOFFER(br0) 192.168.1.11 00:04:e2:aa:b4:d0
2005-02-01 11:23:18 Daemon.Info 192.168.1.1 dnsmasq[49]: DHCPREQUEST(br0) 192.168.1.11 00:04:e2:aa:b4:d0
2005-02-01 11:23:18 Daemon.Info 192.168.1.1 dnsmasq[49]: DHCPACK(br0) 192.168.1.11 00:04:e2:aa:b4:d0 int
2005-02-01 11:23:21 Daemon.Info 192.168.1.1 dnsmasq[49]: DHCPINFORM(br0) 192.168.1.11 00:04:e2:aa:b4:d0
2005-02-01 11:23:21 Daemon.Info 192.168.1.1 dnsmasq[49]: DHCPACK(br0) 192.168.1.11 00:04:e2:aa:b4:d0 int

#RESET ISSUE

#NO INTERNET AFTER RESET
2005-02-01 11:23:22 User.Warning 192.168.1.1 kernel: lp driver: get device ID
2005-02-01 11:23:22 User.Warning 192.168.1.1 kernel: neg fail
2005-02-01 11:23:22 User.Warning 192.168.1.1 kernel: neg fail
2005-02-01 11:23:26 Daemon.Info 192.168.1.1 dnsmasq[49]: DHCPINFORM(br0) 192.168.1.11 00:04:e2:aa:b4:d0
2005-02-01 11:23:26 Daemon.Info 192.168.1.1 dnsmasq[49]: DHCPACK(br0) 192.168.1.11 00:04:e2:aa:b4:d0 int
2005-02-01 11:23:56 Daemon.Warning 192.168.1.1 pppd[75]: Timeout waiting for PADS packets
2005-02-01 11:23:56 Daemon.Error 192.168.1.1 pppd[75]: Unable to complete PPPoE Discovery
2005-02-01 11:24:30 User.Emerg 192.168.1.1 wan: connected manually
2005-02-01 11:24:44 User.Emerg 192.168.1.1 wan: disconnected manually
2005-02-01 11:24:45 Daemon.Info 192.168.1.1 pppd[75]: Hangup (SIGHUP)
2005-02-01 11:24:45 Daemon.Info 192.168.1.1 pppd[75]: Terminating on signal 15.
2005-02-01 11:24:46 Daemon.Info 192.168.1.1 dnsmasq[49]: read /etc/hosts - 4 addresses
2005-02-01 11:24:46 Daemon.Info 192.168.1.1 dnsmasq[49]: read /etc/ethers - 2 addresses
2005-02-01 11:24:46 Daemon.Info 192.168.1.1 dnsmasq[49]: reading /tmp/resolv.conf
2005-02-01 11:24:52 User.Emerg 192.168.1.1 wan: connected manually
2005-02-01 11:24:53 Daemon.Info 192.168.1.1 pppd[75]: Hangup (SIGHUP)
2005-02-01 11:24:53 Daemon.Info 192.168.1.1 pppd[75]: Terminating on signal 15.
2005-02-01 11:24:53 Daemon.Error 192.168.1.1 pppd[75]: recv (receivePacket)
2005-02-01 11:24:54 Daemon.Info 192.168.1.1 pppd[130]: Plugin rp-pppoe.so loaded.
2005-02-01 11:24:54 Daemon.Info 192.168.1.1 pppd[130]: RP-PPPoE plugin version 3.3 compiled against pppd 2.4.2
2005-02-01 11:24:54 Daemon.Notice 192.168.1.1 pppd[131]: pppd 2.4.2 started by admin, uid 0
2005-02-01 11:25:33 User.Emerg 192.168.1.1 wan: connected manually
2005-02-01 11:25:36 Daemon.Warning 192.168.1.1 pppd[131]: Timeout waiting for PADS packets
2005-02-01 11:25:36 Daemon.Error 192.168.1.1 pppd[131]: Unable to complete PPPoE Discovery

#UPDATE FIRMWARE

2005-02-01 11:25:54 User.Notice 192.168.1.1 kernel: Kernel log daemon exiting.
2005-02-01 11:25:54 Syslog.Info 192.168.1.1 System log daemon exiting.

or attach file for a full syslog:

Colonizer

01-02-2005, 11:48

Please specify your connection type. Is it PPTP? DHCP ?

CR3c should display 1.9.2.7-3c in the "Firmware Release" field, stock firmware should not display Release field at all. If you do not have Release field - this is not a custom firmware. Check this picture http://oleg.wl500g.info/1.9.2.7-3c/1.9.2.7-3c.jpg

I use PPoE in Germany
i flashed your 1.9.2.7 c3 succesfully (Release field displayed 1.9.2.7-3c)

Oleg

01-02-2005, 11:53

I dont detected any error, but i think the error about reset issue are in:

DHCPINFORM(br0) 192.168.1.11 00:04:e2:aa:b4:d0
2005-02-01 11:23:21 Daemon.Info 192.168.1.1 dnsmasq[49]: DHCPACK(br0) 192.168.1.11 00:04:e2:aa:b4:d0 int

are to many msg...

Well, in fact it should not cause reboot. Does 192.168.1.11 uses wireless connection?

Oleg

01-02-2005, 11:57

I use PPoE in Germany
i flashed your 1.9.2.7 c3 succesfully (Release field displayed 1.9.2.7-3c)
PPPoE works fine for me, there should not be any problems.
It should either do not work at all, or work for every site.

int

01-02-2005, 15:00

Well, in fact it should not cause reboot. Does 192.168.1.11 uses wireless connection?

yes! the 192.168.1.11 use wireless connection!
the conditions are the same, that i use in other fw, and have strong signal.

Oleg

01-02-2005, 16:21

yes! the 192.168.1.11 use wireless connection!
the conditions are the same, that i use in other fw, and have strong signal.
If you use WPA or WPA-PSK, then this strangeness is probably due to WPA supplicant software (i.e. vendor utilities). If you're running WXP SP2, then it's probably a good idea to remove utilities and let windows to configure your card.

Colonizer

01-02-2005, 18:45

PPPoE works fine for me, there should not be any problems.
It should either do not work at all, or work for every site.

if i connect directly to my ISP without the Asus, i did not get any DNS Server Errors, i can connect to Ebay in my account.
with the CR3c i was not able to log in ebay.

strange
maybe ill tray again next week

hugo

01-02-2005, 18:45

Does this firmware allow to use the rootfs from a stock wlhdd firmware? I have extracted rootfs from 1.2.3.2 WLHDD. Would I need the kernel image too?

Oleg

01-02-2005, 18:52

Does this firmware allow to use the rootfs from a stock wlhdd firmware? I have extracted rootfs from 1.2.3.2 WLHDD. Would I need the kernel image too?
Have not tried that, as I do not have wl-hdd, but it should work. No kernel image needed, but I'm suggesting to replace at least wl.o and et.o modules. In fact, replacing whole /lib/modules is a good idea.

int

01-02-2005, 19:07

If you use WPA or WPA-PSK, then this strangeness is probably due to WPA supplicant software (i.e. vendor utilities). If you're running WXP SP2, then it's probably a good idea to remove utilities and let windows to configure your card.

I use only WEP! and i dont use any utilities on windows..... (i dont like them)

hugo

01-02-2005, 19:11

Have not tried that, as I do not have wl-hdd, but it should work. No kernel image needed, but I'm suggesting to replace at least wl.o and et.o modules. In fact, replacing whole /lib/modules is a good idea.
Don't you think I would get a better speed using the one from the stock firmware? Latest tests from 1.2.3.0 shows a good speed measurement?

Oleg

01-02-2005, 19:31

Latest tests from 1.2.3.0 shows a good speed measurement?
Unlikely. They've got speed increase due to switching to ext3, which I've performed initially. Also, wl-hdd kernel sources is a complete fake.

jbrbv

01-02-2005, 19:47

wds with wpa-psk or wep? (wpa-psk was already broken in 1.9.2.7)
WDS with WPA-PSK/AES. I used it with the previous version 1.9.2.7-3b.

Oleg

01-02-2005, 20:00

WDS with WPA-PSK/AES. I used it with the previous version 1.9.2.7-3b.
WDS with WPA/WPA-PSK never worked with 1.9.2.7, I'm wonder why it worked in 3b. If I recall correctly there was no changes in this part in the 3c.

hugo

01-02-2005, 20:04

Unlikely. They've got speed increase due to switching to ext3, which I've performed initially. Also, wl-hdd kernel sources is a complete fake.

After testing, I had my wl-hdd booting a system. But probably all nvram are false, because I couldn't access it using wifi or ethernet. Usuallly when switching from one to one other, I still get some heartbeat by scanning the network cable. I suppose it has booted, but not set any value.

I leave the next part for the more adventurous, my baby daughter need more attention than my wl-hdd right now :)

Oleg

01-02-2005, 20:20

yes, nvram settings are totally different. this due to the fact, that stock wl-hdd uses semi-complete 1.8 style firmware. :)

kn0rz

02-02-2005, 12:26

Styno

02-02-2005, 13:19

Perhaps you need to set 'case sensitive' to 'Yes' too.

jbrbv

02-02-2005, 21:44

WDS with WPA/WPA-PSK never worked with 1.9.2.7, I'm wonder why it worked in 3b. If I recall correctly there was no changes in this part in the 3c.
I'm now using 2 WL-500g's, WDS with WPA-PSK/AES and 1.9.2.8. I got confused by your answer about 1.9.2.7.
I'll try the Oleg versions with WDS.

Antiloop

03-02-2005, 00:51

First of all: Great work Oleg. Everthing works just fine.

So, I've got a problem concerning my smb.conf. I searched the internet for quite a while, read some forums and then built my smb.conf. All commands seem to be okay, I can access the share via network.
But whenever I copy new files on the share, the filenames are changed to lower case.

I'll just post my smb.conf, maybe s.o. has got an idea what's wrong:

[general]
workgroup = ASD1
netbios name = abc
server string = abc
preserve modes = Yes
preserve case = Yes // Don't change filenames - doesn't (?) work
interfaces = 192.168.1.129/24
mangled names = No
log file = /tmp/harddisk/samba-log.%m
default case = Upper
case sensetive = No
mangle case = No

[wl-hdd]
path = /tmp/harddisk/
public = Yes
writeable = Yes
browseable = Yes

try this:

[global]
workgroup = WERKGROEP
guest account = nobody
security = share
browseable = yes
guest ok = yes
guest only = yes
log level = 1
max log size = 100
encrypt passwords = no
preserve case = yes
short preserve case = yes

[share]
path = /tmp/harddisk

[share$]
path = /tmp/harddisk
writable = yes
force user = root
browseable = no

In NT I had the problem that using names shorter than 8 letters were converted to lower when naming it like 'UPPER' you can set this nvram value to solve this

nvram set usb_vfat_options=shortname=winnt

gilsas

03-02-2005, 09:12

Hello,

That's my first try with a custom firmware ... I was previously running ASUS stock 1.8.1.9. The router behavior has not drastically changed, WAN connection seems to be as reliable as before. Nevertheless, I face two problems:

- I do not have the expected file structure ... most files in /etc/ are misssing (smb.conf, ...) as well as all pre- and post-init scripts ( I have no /usr/local/etc /usr/local/bin, /usr/local/sbin...) :confused: :confused:

- Apart from that, both my USB stick and my USB2 HDD (Maxtor 120Gb + Cypress chipset powered enclosure) do not work anymore ... they are not mounted, and I'm reported unvalid FAT32 fs or something like that. PReviously they were recognized. Of course no smb nor ftp support ... :( :(

Before spending more time, is there a completely stupid thing I've missed ?? (of course I rebooted, but not resetted to defaults) I've unplugged the power cord and rebooted this way as well ...

Thx in advance !! :D

J.B.

03-02-2005, 09:44

Does anyone here have problems to use this firmware version with WL-110 CF Wi-Fi card for Pocket PC? I couldn't make my Pocket PC connect with the previous v.1.9.2.7 version (CR2b). Changing it back to 1.8.1.7-3 solve the issue.

kn0rz

03-02-2005, 10:07

@antiloop: thanks, problem solved. :)

Oleg

03-02-2005, 17:51

- I do not have the expected file structure ... most files in /etc/ are misssing (smb.conf, ...) as well as all pre- and post-init scripts ( I have no /usr/local/etc /usr/local/bin, /usr/local/sbin...) :confused: :confused:

you need to create those directories/files manually as I've stated on my page. they're optional. smb.conf will be automagically generated, once you enable samba from the web interface.

- Apart from that, both my USB stick and my USB2 HDD (Maxtor 120Gb + Cypress chipset powered enclosure) do not work anymore ... they are not mounted, and I'm reported unvalid FAT32 fs or something like that. PReviously they were recognized. Of course no smb nor ftp support ... :( :(

nobody able to guess the errors based on the "something like that", so post your system log.

kreator

03-02-2005, 20:44

Yes reset issue are present!!

Unfortunately, yes, it reboots by itself under a higher load. Probably a kernel issue (usb drivers, for instance?) :(

JaraNovak

04-02-2005, 10:34

How to change to client mode wuth this FW? Please help me, I'm lama :o Is it possible to do this via web configurator?

Thanky You!

Oleg

04-02-2005, 10:41

How to change to client mode wuth this FW? Please help me, I'm lama :o Is it possible to do this via web configurator?

Thanky You!
yes, the only way is web config.

JaraNovak

04-02-2005, 10:43

Thanx:-) A could you possibly tell me how? I'm searching every settings, but I don't know how to change and setup it.

(sorry for my bad english, I'm Czech;-))

dikko

04-02-2005, 11:57

When I use asus latest firmware wl1524 my voip works good. The only thing wrong with this firmware is that the internet stops after a while. Wan port disconnect connect. When I use oleg firmware 1927.2 3a,3b,3c Voip telephone is not working oke. The outgoing pakket are okay but the incomming are a little bit delayed. Telephone conversation is no good quality.

your regards

Dirk Hofman :confused:

Oleg

04-02-2005, 14:17

Thanx:-) A could you possibly tell me how? I'm searching every settings, but I don't know how to change and setup it.

(sorry for my bad english, I'm Czech;-))
Wireless -> Advanced -> Extended mode -> Station

JaraNovak

04-02-2005, 14:21

Wireless -> Advanced -> Extended mode -> Station
Thank you, Oleg! But There's no Extended mode. I see only Wireless -> Advanced and that's all! So where is the problem? Can you post me an image of it? Thank you

Oleg

04-02-2005, 14:29

Thank you, Oleg! But There's no Extended mode. I see only Wireless -> Advanced and that's all! So where is the problem? Can you post me an image of it? Thank you
That's it.

JaraNovak

04-02-2005, 14:46

Aha, so there's some problem at me. Because I can see only this:

Does it depends on using wl-500b instead of wl-500g? What is wrong?

Oleg

04-02-2005, 14:53

Most likely you've wl500bv2 unit, which is based on the ralink radio, which seems to be unsupported.
I'm wonder, why you've bought 802.11b only unit?

JaraNovak

04-02-2005, 15:00

Most likely you've wl500bv2 unit, which is based on the ralink radio, which seems to be unsupported.
I'm wonder, why you've bought 802.11b only unit?

I don't know, wheter it is wl500b or wl500bv2. I bought it 19.2.2004. It seems you are right and it is wl500bv2. I have no luck:-(

Oleg

04-02-2005, 15:09

I don't know, wheter it is wl500b or wl500bv2. I bought it 19.2.2004. It seems you are right and it is wl500bv2. I have no luck:-(
Which firmware you've flashed then? wl500b or wl500bv2? :confused:

JaraNovak

04-02-2005, 15:15

Which firmware you've flashed then? wl500b or wl500bv2? :confused:

wl500bv2...

But now, I have next problem - Air LED doesn't light...

Oleg

04-02-2005, 15:26

wl500bv2...

But now, I have next problem - Air LED doesn't light...
fine... I'm very impressed... :D
Please type

cat /proc/pci

in the hidden admin page and press refresh. Post results here.

JaraNovak

04-02-2005, 15:31

Here is a result:

PCI devices found:
Bus 0, device 0, function 0:
Class 0500: PCI device 14e4:0803 (rev 0).
IRQ 6.
Non-prefetchable 32 bit memory at 0x18000000 [0x18000fff].
Non-prefetchable 32 bit memory at 0x0 [0x7ffffff].
Non-prefetchable 32 bit memory at 0x10000000 [0x17ffffff].
Non-prefetchable 32 bit memory at 0x80000000 [0xffffffff].
Bus 0, device 1, function 0:
Class 0200: PCI device 14e4:4711 (rev 0).
IRQ 5.
Non-prefetchable 32 bit memory at 0x18001000 [0x18001fff].
Bus 0, device 2, function 0:
Class 0200: PCI device 14e4:4713 (rev 0).
IRQ 3.
Non-prefetchable 32 bit memory at 0x18002000 [0x18002fff].
Bus 0, device 3, function 0:
Class 0703: PCI device 14e4:4712 (rev 0).
IRQ 2.
Non-prefetchable 32 bit memory at 0x18003000 [0x18003fff].
Bus 0, device 4, function 0:
Class 0c03: PCI device 14e4:4715 (rev 0).
IRQ 2.
Non-prefetchable 32 bit memory at 0x18004000 [0x18004fff].
Bus 0, device 5, function 0:
Class 0604: PCI device 14e4:0804 (rev 0).
IRQ 6.
Non-prefetchable 32 bit memory at 0x18005000 [0x18005fff].
Non-prefetchable 32 bit memory at 0x8000000 [0xfffffff].
Bus 0, device 6, function 0:
Class 0b30: PCI device 14e4:0805 (rev 0).
IRQ 6.
Non-prefetchable 32 bit memory at 0x18006000 [0x18006fff].
Non-prefetchable 32 bit memory at 0xff200000 [0xff3fffff].
Bus 0, device 7, function 0:
Class 0501: PCI device 14e4:0811 (rev 0).
IRQ 2.
Non-prefetchable 32 bit memory at 0x18007000 [0x18007fff].
Non-prefetchable 32 bit memory at 0x1f000000 [0x1fffffff].
Bus 0, device 8, function 0:
Class 0200: PCI device 14e4:4713 (rev 0).
IRQ 4.
Non-prefetchable 32 bit memory at 0x18008000 [0x18008fff].
Bus 1, device 0, function 0:
Class 0600: PCI device 14e4:4710 (rev 1).
IRQ 6.
Non-prefetchable 32 bit memory at 0x40000000 [0x40001fff].
Prefetchable 32 bit memory at 0x0 [0x7ffffff].
Bus 1, device 2, function 0:
Class 0280: PCI device 14e4:4301 (rev 2).
IRQ 6.
Non-prefetchable 32 bit memory at 0x40002000 [0x40003fff].

Oleg

04-02-2005, 15:38

Here is a result:

Bus 1, device 2, function 0:
Class 0280: PCI device 14e4:4301 (rev 2).
IRQ 6.
Non-prefetchable 32 bit memory at 0x40002000 [0x40003fff].

You've wl500b unit with broadcom radio. Flash wl500b firmware using firmware restoration mode. v2 stays for hardware revision, not for "even cooler" firmware.

JaraNovak

04-02-2005, 15:50

Dear Oleg,
thank you very much! Now everything works well, I'm going to test it.
Where can I see reasonable APs?

gilsas

04-02-2005, 18:15

you need to create those directories/files manually as I've stated on my page. they're optional. smb.conf will be automagically generated, once you enable samba from the web interface.

nobody able to guess the errors based on the "something like that", so post your system log.

Ok, thank you very much Oleg. I was somewhat dissapointed not to find the mentionned folders so I did not keep on reading the rest.

The hard disk works fine now even if I do have some strange logs, it's mounted correctly. I'm not at home right now so no way to post the log. The USB stick, no way so far. I'm gonna reformat it and will keep you posted for info.

Funny story :D :D :D :D : I kept trying during more than two hours the other day with no sucess .... yesterday when I rebooted the external case I found the HDD very silent ... too silent: actually the HDD was still in my PC connected through the IDE cable while I was stupidely trying to mount an empty USB case :D :D :D :D

Cheers,

pershing

08-02-2005, 19:01

It's wl500b or wl500bv2?

PCI devices found:
Bus 0, device 0, function 0:
Class 0500: PCI device 14e4:0803 (rev 0).
IRQ 6.
Non-prefetchable 32 bit memory at 0x18000000 [0x18000fff].
Non-prefetchable 32 bit memory at 0x0 [0x7ffffff].
Non-prefetchable 32 bit memory at 0x10000000 [0x17ffffff].
Non-prefetchable 32 bit memory at 0x80000000 [0xffffffff].
Bus 0, device 1, function 0:
Class 0200: PCI device 14e4:4711 (rev 0).
IRQ 5.
Non-prefetchable 32 bit memory at 0x18001000 [0x18001fff].
Bus 0, device 2, function 0:
Class 0200: PCI device 14e4:4713 (rev 0).
IRQ 3.
Non-prefetchable 32 bit memory at 0x18002000 [0x18002fff].
Bus 0, device 3, function 0:
Class 0703: PCI device 14e4:4712 (rev 0).
IRQ 2.
Non-prefetchable 32 bit memory at 0x18003000 [0x18003fff].
Bus 0, device 4, function 0:
Class 0c03: PCI device 14e4:4715 (rev 0).
IRQ 2.
Non-prefetchable 32 bit memory at 0x18004000 [0x18004fff].
Bus 0, device 5, function 0:
Class 0604: PCI device 14e4:0804 (rev 0).
IRQ 6.
Non-prefetchable 32 bit memory at 0x18005000 [0x18005fff].
Non-prefetchable 32 bit memory at 0x8000000 [0xfffffff].
Bus 0, device 6, function 0:
Class 0b30: PCI device 14e4:0805 (rev 0).
IRQ 6.
Non-prefetchable 32 bit memory at 0x18006000 [0x18006fff].
Non-prefetchable 32 bit memory at 0xff200000 [0xff3fffff].
Bus 0, device 7, function 0:
Class 0501: PCI device 14e4:0811 (rev 0).
IRQ 2.
Non-prefetchable 32 bit memory at 0x18007000 [0x18007fff].
Non-prefetchable 32 bit memory at 0x1f000000 [0x1fffffff].
Bus 0, device 8, function 0:
Class 0200: PCI device 14e4:4713 (rev 0).
IRQ 4.
Non-prefetchable 32 bit memory at 0x18008000 [0x18008fff].
Bus 1, device 0, function 0:
Class 0600: PCI device 14e4:4710 (rev 1).
IRQ 6.
Non-prefetchable 32 bit memory at 0x40000000 [0x40001fff].
Prefetchable 32 bit memory at 0x0 [0x7ffffff].
Bus 1, device 2, function 0:
Class 0280: PCI device 1814:0101 (rev 0).
IRQ 6.
Non-prefetchable 32 bit memory at 0x40002000 [0x40003fff].

I need client mode with this hardware ....

Which firmware I have to use?

Thank You

Oleg

08-02-2005, 19:22

Bus 1, device 2, function 0:
Class 0280: PCI device 1814:0101 (rev 0).
IRQ 6.
Non-prefetchable 32 bit memory at 0x40002000 [0x40003fff].

I need client mode with this hardware ....

Which firmware I have to use?
wl500b v2 and it's probably stated somewhere on the unit as well as in the firmware upgrade page. As for client mode - it's probably not supported with RALink.

pershing

08-02-2005, 19:36

wl500b v2 and it's probably stated somewhere on the unit as well as in the firmware upgrade page. As for client mode - it's probably not supported with RALink

I am loser .... :-(((

I'm use Celeron 300 with XP with firewall in function router... Cost electricity is to much...

I' hopest better news...

Thank You very match.

Excuse me may englisch....

Oleg

08-02-2005, 20:22

just replace the card inside to wl120g and you will get wl500g.

cunami

09-02-2005, 19:07

Hello,

I'm using latest firmware (v. 1.9.2.7 CR3c [Oleg]) on Asus WL-500G and having problems with configuring timeout - when my router should disconnect from ISP. Tried both versions - with "Tx Only" checked and unchecked and no success :confused: "Idle Disconnect Time in seconds" is 1800. But seems my router does not disconnect from ISP for a long time when there is no internet usage at all. Here is a part of my log:

Feb 9 08:29:41 pppd[82]: LCP terminated by peer
Feb 9 08:29:42 dnsmasq[51]: read /etc/hosts - 4 addresses
Feb 9 08:29:42 dnsmasq[51]: reading /tmp/resolv.conf
Feb 9 08:29:42 dnsmasq[51]: using nameserver xxx.xxx.xxx.xxx#xx
Feb 9 08:29:42 PPPoE: Disconnected
Feb 9 08:29:42 pppd[82]: Child process /tmp/ppp/ip-down (pid 386) terminated with signal 11
Feb 9 08:29:45 pppd[82]: Connection terminated.
Feb 9 08:29:45 pppd[82]: Connect time 42.6 minutes.
Feb 9 08:29:45 pppd[82]: Sent 64 bytes, received 3088 bytes.
Feb 9 08:30:15 pppoe-relay[80]: PADO packet from xx:xx:xx:xx:xx:xx on interface eth1 does not have Relay-Session-Id tag
Feb 9 08:30:15 pppd[82]: PPP session is 2552
Feb 9 08:30:15 pppoe-relay[80]: PADS packet from xx:xx:xx:xx:xx:xx on interface eth1 does not have Relay-Session-Id tag
Feb 9 08:30:15 pppd[82]: Using interface ppp0
Feb 9 08:30:15 pppd[82]: Connect: ppp0 <--> eth1
Feb 9 08:30:15 pppd[82]: PAP authentication succeeded
Feb 9 08:30:15 pppd[82]: peer from calling number xx:xx:xx:xx:xx:xx authorized
Feb 9 08:30:15 pppoe-relay[80]: Discovery packet on eth1 with unknown code 211
Feb 9 08:30:15 pppd[82]: local IP address xxx.xxx.xxx.xxx
Feb 9 08:30:15 pppd[82]: remote IP address xxx.xxx.xxx.xxx
Feb 9 08:30:15 pppd[82]: primary DNS address xxx.xxx.xxx.xxx
Feb 9 08:30:15 pppd[82]: secondary DNS address xxx.xxx.xxx.xxx
Feb 9 08:30:16 dnsmasq[51]: read /etc/hosts - 4 addresses
Feb 9 08:30:16 dnsmasq[51]: reading /tmp/resolv.conf
Feb 9 08:30:16 dnsmasq[51]: using nameserver xxx.xxx.xxx.xxx#xx
Feb 9 08:30:16 dnsmasq[51]: using nameserver xxx.xxx.xxx.xxx#xx
Feb 9 08:30:16 PPPoE: connect to ISP
Feb 9 17:38:35 pppd[82]: No response to 6 echo-requests
Feb 9 17:38:35 pppd[82]: Serial link appears to be disconnected.
Feb 9 17:38:35 dnsmasq[51]: read /etc/hosts - 4 addresses
Feb 9 17:38:35 dnsmasq[51]: reading /tmp/resolv.conf
Feb 9 17:38:35 dnsmasq[51]: using nameserverxxx.xxx.xxx.xxx#xx
Feb 9 17:38:35 PPPoE: Disconnected
Feb 9 17:38:41 pppd[82]: Connection terminated.
Feb 9 17:38:41 pppd[82]: Connect time 548.4 minutes.
Feb 9 17:38:41 pppd[82]: Sent 292 bytes, received 115218 bytes.
Feb 9 17:39:46 pppd[82]: Timeout waiting for PADO packets
Feb 9 17:39:46 pppd[82]: Unable to complete PPPoE Discovery
Feb 9 17:40:51 pppd[82]: Timeout waiting for PADO packets
Feb 9 17:40:51 pppd[82]: Unable to complete PPPoE Discovery
Feb 9 17:41:56 pppd[82]: Timeout waiting for PADO packets
Feb 9 17:41:56 pppd[82]: Unable to complete PPPoE Discovery
Feb 9 17:43:01 pppd[82]: Timeout waiting for PADO packets
Feb 9 17:43:01 pppd[82]: Unable to complete PPPoE Discovery
Feb 9 17:44:06 pppd[82]: Timeout waiting for PADO packets
Feb 9 17:44:06 pppd[82]: Unable to complete PPPoE Discovery
Feb 9 17:45:11 pppd[82]: Timeout waiting for PADO packets
Feb 9 17:45:11 pppd[82]: Unable to complete PPPoE Discovery
Feb 9 17:46:16 pppd[82]: Timeout waiting for PADO packets
Feb 9 17:46:16 pppd[82]: Unable to complete PPPoE Discovery
Feb 9 17:47:21 pppd[82]: Timeout waiting for PADO packets
Feb 9 17:47:21 pppd[82]: Unable to complete PPPoE Discovery
Feb 9 17:48:26 pppd[82]: Timeout waiting for PADO packets
Feb 9 17:48:26 pppd[82]: Unable to complete PPPoE Discovery
Feb 9 17:49:31 pppd[82]: Timeout waiting for PADO packets
Feb 9 17:49:31 pppd[82]: Unable to complete PPPoE Discovery
Feb 9 17:49:31 pppd[82]: Connect time 548.4 minutes.
Feb 9 17:49:31 pppd[82]: Sent 292 bytes, received 115218 bytes.
Feb 9 17:49:31 pppd[82]: Exit.

From here you can see 2 problems:

Feb 9 08:30:16 PPPoE: connect to ISP
Feb 9 17:38:35 pppd[82]: No response to 6 echo-requests

seems that router was connected to ISP from 08:30 to 17:38 - this is much more than 1800 secords :-) I can guarantee that nobody was using at this time as I am only one user and I wasn't at home at all :D

and the second problem is that after long period connected some problems somethimes comes (Timeout waiting for PADO packets) and after that pppd just exits and then I need to reboot my router before I can connect to my ISP and have internet again.

Maybe somebody could help me with suggestions what can I do to avoid these problems?

Thank you!
P.S. I'm connecting to ISP through PPPoE and it is configured (entered all login information) in router site to connect automaticly.

Oleg

09-02-2005, 21:11

cunami

09-02-2005, 22:26

Have you specified DNS server addresses? This is required for idle to work and is stated on my page... It will not work with auto setting.

Seems I did not read your site very carefuly :rolleyes: and my DNS addresses are autoconfigured. So I will try to add them manualy and then will see what happen. Thank you very much Oleg for your help!

cunami

10-02-2005, 17:04

Hello again,

so I have tried to configure my router as you told me, and seems still the same problem persist. Here is how log looks now:

Feb 10 08:44:59 pppd[82]: Connection terminated.
Feb 10 08:44:59 pppd[82]: Connect time 5.1 minutes.
Feb 10 08:44:59 pppd[82]: Sent 40 bytes, received 114 bytes.
Feb 10 08:45:29 pppoe-relay[80]: PADO packet from xx:xx:xx:xx:xx:xx on interface eth1 does not have Relay-Session-Id tag
Feb 10 08:45:30 pppd[82]: PPP session is 7456
Feb 10 08:45:30 pppoe-relay[80]: PADS packet from xx:xx:xx:xx:xx:xx on interface eth1 does not have Relay-Session-Id tag
Feb 10 08:45:30 pppd[82]: Using interface ppp0
Feb 10 08:45:30 pppd[82]: Connect: ppp0 <--> eth1
Feb 10 08:45:30 pppd[82]: PAP authentication succeeded
Feb 10 08:45:30 pppd[82]: peer from calling number xx:xx:xx:xx:xx:xx authorized
Feb 10 08:45:30 pppoe-relay[80]: Discovery packet on eth1 with unknown code 211
Feb 10 08:45:30 pppd[82]: local IP address xxx.xxx.xxx.xxx
Feb 10 08:45:30 pppd[82]: remote IP address xxx.xxx.xxx.xxx
Feb 10 08:45:30 dnsmasq[51]: read /etc/hosts - 4 addresses
Feb 10 08:45:30 dnsmasq[51]: reading /tmp/resolv.conf
Feb 10 08:45:30 dnsmasq[51]: using nameserver xxx.xxx.xxx.xxx#53
Feb 10 08:45:30 dnsmasq[51]: using nameserver xxx.xxx.xxx.xxx#53
Feb 10 08:45:31 PPPoE: connect to ISP
Feb 10 09:10:31 pppd[82]: LCP terminated by peer
Feb 10 09:10:31 dnsmasq[51]: read /etc/hosts - 4 addresses
Feb 10 09:10:31 dnsmasq[51]: reading /tmp/resolv.conf
Feb 10 09:10:31 dnsmasq[51]: using nameserver xxx.xxx.xxx.xxx#53
Feb 10 09:10:31 dnsmasq[51]: using nameserver xxx.xxx.xxx.xxx#53
Feb 10 09:10:31 PPPoE: Disconnected
Feb 10 09:10:31 pppd[82]: Child process /tmp/ppp/ip-down (pid 354) terminated with signal 11
Feb 10 09:10:34 pppd[82]: Connection terminated.
Feb 10 09:10:34 pppd[82]: Connect time 25.1 minutes.
Feb 10 09:10:34 pppd[82]: Sent 40 bytes, received 4116 bytes.
Feb 10 09:11:04 pppoe-relay[80]: PADO packet from xx:xx:xx:xx:xx:xx on interface eth1 does not have Relay-Session-Id tag
Feb 10 09:11:04 pppd[82]: PPP session is 3224
Feb 10 09:11:04 pppoe-relay[80]: PADS packet from xx:xx:xx:xx:xx:xx on interface eth1 does not have Relay-Session-Id tag
Feb 10 09:11:04 pppd[82]: Using interface ppp0
Feb 10 09:11:04 pppd[82]: Connect: ppp0 <--> eth1
Feb 10 09:11:04 pppd[82]: PAP authentication succeeded
Feb 10 09:11:04 pppd[82]: peer from calling number xx:xx:xx:xx:xx:xx authorized
Feb 10 09:11:04 pppoe-relay[80]: Discovery packet on eth1 with unknown code 211
Feb 10 09:11:05 pppd[82]: local IP address xxx.xxx.xxx.xxx
Feb 10 09:11:05 pppd[82]: remote IP address xxx.xxx.xxx.xxx
Feb 10 09:11:05 dnsmasq[51]: read /etc/hosts - 4 addresses
Feb 10 09:11:05 dnsmasq[51]: reading /tmp/resolv.conf
Feb 10 09:11:05 dnsmasq[51]: using nameserver xxx.xxx.xxx.xxx#53
Feb 10 09:11:05 dnsmasq[51]: using nameserver xxx.xxx.xxx.xxx#53
Feb 10 09:11:05 PPPoE: connect to ISP
Feb 10 09:23:35 pppd[82]: LCP terminated by peer
Feb 10 09:23:35 dnsmasq[51]: read /etc/hosts - 4 addresses
Feb 10 09:23:35 dnsmasq[51]: reading /tmp/resolv.conf
Feb 10 09:23:35 dnsmasq[51]: using nameserver xxx.xxx.xxx.xxx#53
Feb 10 09:23:35 dnsmasq[51]: using nameserver xxx.xxx.xxx.xxx#53
Feb 10 09:23:35 PPPoE: Disconnected
Feb 10 09:23:35 pppd[82]: Child process /tmp/ppp/ip-down (pid 370) terminated with signal 11
Feb 10 09:23:38 pppd[82]: Connection terminated.
Feb 10 09:23:38 pppd[82]: Connect time 12.6 minutes.
Feb 10 09:23:38 pppd[82]: Sent 40 bytes, received 258 bytes.
Feb 10 09:24:08 pppoe-relay[80]: PADO packet from xx:xx:xx:xx:xx:xx on interface eth1 does not have Relay-Session-Id tag
Feb 10 09:24:08 pppd[82]: PPP session is 5196
Feb 10 09:24:08 pppoe-relay[80]: PADS packet from xx:xx:xx:xx:xx:xx on interface eth1 does not have Relay-Session-Id tag
Feb 10 09:24:08 pppd[82]: Using interface ppp0
Feb 10 09:24:08 pppd[82]: Connect: ppp0 <--> eth1
Feb 10 09:24:08 pppd[82]: PAP authentication succeeded
Feb 10 09:24:08 pppd[82]: peer from calling number xx:xx:xx:xx:xx:xx authorized
Feb 10 09:24:09 pppoe-relay[80]: Discovery packet on eth1 with unknown code 211
Feb 10 09:24:09 pppd[82]: local IP address xxx.xxx.xxx.xxx
Feb 10 09:24:09 pppd[82]: remote IP address xxx.xxx.xxx.xxx
Feb 10 09:24:09 dnsmasq[51]: read /etc/hosts - 4 addresses
Feb 10 09:24:09 dnsmasq[51]: reading /tmp/resolv.conf
Feb 10 09:24:09 dnsmasq[51]: using nameserver xxx.xxx.xxx.xxx#53
Feb 10 09:24:09 dnsmasq[51]: using nameserver xxx.xxx.xxx.xxx#53
Feb 10 09:24:09 PPPoE: connect to ISP
Feb 10 09:29:08 pppd[82]: LCP terminated by peer
Feb 10 09:29:09 dnsmasq[51]: read /etc/hosts - 4 addresses
Feb 10 09:29:09 dnsmasq[51]: reading /tmp/resolv.conf
Feb 10 09:29:09 dnsmasq[51]: using nameserver xxx.xxx.xxx.xxx#53
Feb 10 09:29:09 dnsmasq[51]: using nameserver xxx.xxx.xxx.xxx#53
Feb 10 09:29:09 PPPoE: Disconnected
Feb 10 09:29:09 pppd[82]: Child process /tmp/ppp/ip-down (pid 386) terminated with signal 11
Feb 10 09:29:12 pppd[82]: Connection terminated.
Feb 10 09:29:12 pppd[82]: Connect time 5.0 minutes.
Feb 10 09:29:12 pppd[82]: Sent 40 bytes, received 114 bytes.
Feb 10 09:29:42 pppoe-relay[80]: PADO packet from xx:xx:xx:xx:xx:xx on interface eth1 does not have Relay-Session-Id tag
Feb 10 09:29:42 pppd[82]: PPP session is 5927
Feb 10 09:29:42 pppoe-relay[80]: PADS packet from xx:xx:xx:xx:xx:xx on interface eth1 does not have Relay-Session-Id tag
Feb 10 09:29:42 pppd[82]: Using interface ppp0
Feb 10 09:29:42 pppd[82]: Connect: ppp0 <--> eth1
Feb 10 09:29:42 pppd[82]: PAP authentication succeeded
Feb 10 09:29:42 pppd[82]: peer from calling number xx:xx:xx:xx:xx:xx authorized
Feb 10 09:29:42 pppoe-relay[80]: Discovery packet on eth1 with unknown code 211
Feb 10 09:29:42 pppd[82]: local IP address xxx.xxx.xxx.xxx
Feb 10 09:29:42 pppd[82]: remote IP address xxx.xxx.xxx.xxx
Feb 10 09:29:43 dnsmasq[51]: read /etc/hosts - 4 addresses
Feb 10 09:29:43 dnsmasq[51]: reading /tmp/resolv.conf
Feb 10 09:29:43 dnsmasq[51]: using nameserver xxx.xxx.xxx.xxx#53
Feb 10 09:29:43 dnsmasq[51]: using nameserver xxx.xxx.xxx.xxx#53
Feb 10 09:29:43 PPPoE: connect to ISP
Feb 10 09:37:12 pppd[82]: LCP terminated by peer
Feb 10 09:37:13 dnsmasq[51]: read /etc/hosts - 4 addresses
Feb 10 09:37:13 dnsmasq[51]: reading /tmp/resolv.conf
Feb 10 09:37:13 dnsmasq[51]: using nameserver xxx.xxx.xxx.xxx#53
Feb 10 09:37:13 dnsmasq[51]: using nameserver xxx.xxx.xxx.xxx#53
Feb 10 09:37:13 PPPoE: Disconnected
Feb 10 09:37:13 pppd[82]: Child process /tmp/ppp/ip-down (pid 402) terminated with signal 11
Feb 10 09:37:15 pppd[82]: Connection terminated.
Feb 10 09:37:15 pppd[82]: Connect time 7.5 minutes.
Feb 10 09:37:15 pppd[82]: Sent 40 bytes, received 210 bytes.
Feb 10 09:37:46 pppoe-relay[80]: PADO packet from xx:xx:xx:xx:xx:xx on interface eth1 does not have Relay-Session-Id tag
Feb 10 09:37:46 pppd[82]: PPP session is 6892
Feb 10 09:37:46 pppoe-relay[80]: PADS packet from xx:xx:xx:xx:xx:xx on interface eth1 does not have Relay-Session-Id tag
Feb 10 09:37:46 pppd[82]: Using interface ppp0
Feb 10 09:37:46 pppd[82]: Connect: ppp0 <--> eth1
Feb 10 09:37:46 pppd[82]: PAP authentication succeeded
Feb 10 09:37:46 pppd[82]: peer from calling number xx:xx:xx:xx:xx:xx authorized
Feb 10 09:37:46 pppoe-relay[80]: Discovery packet on eth1 with unknown code 211
Feb 10 09:37:46 pppd[82]: local IP address xxx.xxx.xxx.xxx
Feb 10 09:37:46 pppd[82]: remote IP address xxx.xxx.xxx.xxx
Feb 10 09:37:47 dnsmasq[51]: read /etc/hosts - 4 addresses
Feb 10 09:37:47 dnsmasq[51]: reading /tmp/resolv.conf
Feb 10 09:37:47 dnsmasq[51]: using nameserver xxx.xxx.xxx.xxx#53
Feb 10 09:37:47 dnsmasq[51]: using nameserver xxx.xxx.xxx.xxx#53
Feb 10 09:37:47 PPPoE: connect to ISP

Now is Feb 10, 18:50 and no disconnect for a long time again. DNS names are configured manualy. I'm attaching screenshot of my configuration:

http://wl500g.info/attachment.php?attachmentid=317&stc=1

After I configured my router with these values, which you see in attachment, I have rebooted my router and this part of log, which you see above is already using this configuration. So what could be here wrong?

Thanks!

Oleg

10-02-2005, 19:18

ok, post the output for

cat /tmp/ppp/options.wan0

Also, 1800 seconds is about 30 minutes, and most likely traffic is still going. Try changing this to 300 seconds (5 minutes) and check if it helps.

cunami

10-02-2005, 19:52

ok, post the output for

cat /tmp/ppp/options.wan0

Also, 1800 seconds is about 30 minutes, and most likely traffic is still going. Try changing this to 300 seconds (5 minutes) and check if it helps.

Well at all this time from 9:00 to 18:00 my computer was turned off and this is only one computer who is using internet through router. Wirelles activity is also almost impossible as I've added mac address filtering and log also is emty:

Mode : AP Only
Channel : 11

Stations List
----------------------------------------

here is options.wan0 output:

[admin@(none) /]$ cat /tmp/ppp/options.wan0
noauth refuse-eap
user 'xxxx'
password 'xxxx'
plugin rp-pppoe.so eth1
mru 1492
mtu 1492
tx_only
defaultroute
persist
ipcp-accept-remote ipcp-accept-local noipdefault
ktune
default-asyncmap nopcomp noaccomp
novj nobsdcomp nodeflate
lcp-echo-interval 10
lcp-echo-failure 6
unit 0

[admin@(none) /]$

BTW if Tx Only is checked on then all activity from internet side is not counted yes? Timeout should occur after 30 minutes of no activity from LAN / Wireless side?

Colonizer

12-02-2005, 11:31

Oleg

12-02-2005, 19:16

here is options.wan0 output:

Ok, found a bug in the code. Check your PM.

Oleg

13-02-2005, 09:50

@Oleg

I tried your Firmware 1.9.2.7 CR3b and CR3c but with both of them i can not connect to www.ebay.de with firefox, with the IE i get the mainpage of Ebay.de, but when i want to log into my account i get a DNS or server failure.

with the original Asus 1.9.2.7 i do not have this problem (bit connection Problems with WLAN and dying connection)

i also tried to insert the DNS Servers from my ISP manually, but it is not getting better. (with the original Asus i use the same DNS Servers...)
Do you have any suggestion?
Well, in fact this looks like a tcp mss problem. Could you please type this

iptables -I FORWARD -p tcp --syn -j TCPMSS --clamp-mss-to-pmtu

and check if this helps. If it does not help - try decreasing mtu setting in the web iface - set it to something like 1200 and try again.

Also, could you please type

iptables -L FORDWARD -vn

and post results here?

Colonizer

13-02-2005, 10:56

iptables -I FORWARD -p tcp --syn -j TCPMSS --clamp-mss-to-pmtu

i insertet it on the hidden Adminpage and finished it with enter.
nothing happens (neither a "done" or any result with my ebay problems

after using

iptables -L FORDWARD -vn

i got a message: iptables: Table does not exist (do you need to insmod?)
I rebooted the WL500g and after the reboot, i was able to get to my ebay loginpage (but not further)
i reduces the MTU to 1200 and repeatet everyting twice, but at the end i do not get my ebay login page anymore.

Oleg

13-02-2005, 11:16

Colonizer

13-02-2005, 11:23

hm i do not get any message besides "None"

i also restored factory settings now, but it does not help.

i get the ebay mainpage (only once) and not even a login window...

Oleg

13-02-2005, 11:31

Do you've firewall enabled? In which mode wl500g is running (router, home gateway, ap)?

Colonizer

13-02-2005, 11:37

Firewall is enabled, but i have not made any changes after the factory reset.

i use the Wl500g as HomeGateway.

Edit: Disabling the Firewall is not helping... :confused:
Edit2: with the IE i get the login page of Ebay again, but no successfull login.

majx

13-02-2005, 11:57

I'm working for an Austrian ISP and we had several probs with mtu
-> but rather on sending data than on receiving.
-> IE works fine, mail receive also
-> sending small mails without attachments worked fine
-> sending mail with attachments kickedd the a***

changing mtu to 1492 worked fine for sending mails->
(buggy firmware on some routers!)
changing the mru...well if nessesary....but it should work fine with the defaults.
I rather think it's client-based (some FW or AV on your machine?)
proxy?

majx

13-02-2005, 12:01

do you mean this one?ebay-login (https://signin.ebay.com/ws/eBayISAPI.dll?SignIn)

Colonizer

13-02-2005, 12:15

do you mean this one?ebay-login (https://signin.ebay.com/ws/eBayISAPI.dll?SignIn)

yeap, you are right. either i even do not get to that page, or i am not able to log in there. (DNS Failure with the IE, or Document contains no Data with Firefox).
Login to a hotmail account fails as well, and i get strange smtp-messages when sending mails.
The Strange thing is, that i can make it work, when i use the original Asus Firmware (1.9.2.7) but there i have problems with my WLAN and sometimes the router looses te connection to my isp.
Now i am testing the 1.7.5.9 CR5, and at least Ebay seems to work fine.

Oleg

13-02-2005, 17:23

majx

13-02-2005, 17:31

yeap, you are right. either i even do not get to that page, or i am not able to log in there. (DNS Failure with the IE, or Document contains no Data with Firefox).

Did you add your IP's DNS to your clients config (don't obtain them via DHCP from router!)

pifi

13-02-2005, 20:30

Colonizer

14-02-2005, 21:57

Maybe therefore he sees no output?
The REFRESH-Button should bring a result, without ENTER before :cool:

You are right :eek:

Ill try again tomorrow. Right now everything seems to be OK for me with 1.7.5.9-5 :D

hellwach

15-02-2005, 10:04

Ok, found a bug in the code. Check your PM.

have the same problem, please can you help me too? thanx

Colonizer

15-02-2005, 10:39

@ Oleg

the first command brings no result.

Chain FORWARD (policy ACCEPT 83 packets, 4316 bytes)
pkts bytes target prot opt in out source destination
2 104 TCPMSS tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp flags:0x16/0x02 TCPMSS clamp to PMTU
36 1872 TCPMSS tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp flags:0x16/0x02 TCPMSS clamp to PMTU
36 1872 TCPMSS tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp flags:0x16/0x02 TCPMSS clamp to PMTU
1432 669K ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED
0 0 DROP all -- * * 0.0.0.0/0 0.0.0.0/0 state INVALID
0 0 ACCEPT all -- br0 br0 0.0.0.0/0 0.0.0.0/0
47 2444 TCPMSS tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp flags:0x06/0x02 tcpmss match 1453:65535TCPMSS set 1452
0 0 ACCEPT tcp -- ppp0 * 0.0.0.0/0 0.0.0.0/0 tcp flags:0x16/0x02 limit: avg 1/sec burst 5
0 0 ACCEPT tcp -- ppp0 * 0.0.0.0/0 0.0.0.0/0 tcp flags:0x17/0x04 limit: avg 1/sec burst 5
0 0 ACCEPT icmp -- ppp0 * 0.0.0.0/0 0.0.0.0/0 limit: avg 1/sec burst 5 icmp type 8
0 0 ACCEPT udp -- * * 0.0.0.0/0 0.0.0.0/0

ebay problem still there...

by the way, with the new Firmware i can not reply to posts here in this forum.

Oleg

15-02-2005, 12:19

have the same problem, please can you help me too? thanx
Check your PM.

Oleg

15-02-2005, 12:22

@ Oleg

the first command brings no result.
ebay problem still there...

by the way, with the new Firmware i can not reply to posts here in this forum.
Have you checked other 1.9.2.7 versions? I mean 1.9.2.7-1, 1.9.2.7-2, 1.9.2.7-3b?

Colonizer

15-02-2005, 17:43

the same with 3b

Wesleyrpg

18-02-2005, 06:29

this firmware is pretty awesome thanks, almost as good as 1.8.1.7-2a, but it still has a few bigpond issues. It boots me off the network once or twice an hour for about 5 mins...and then reconnects me automatically!

Every firmware where i have to enter the heartbeat IP address manually, does the same thing!

1.8.1.7-2a and 1.7.5.9 CR5 are the only exceptions where in don't have to enter a IP address, and they are the only two that pretty much work flawlessly!

here is a log....of the latest firmware, maybe you can see something wrong?

Jan 1 11:00:14 dhcp client: bound IP : 192.168.100.11 from
Jan 1 11:00:14 bpalogin[110]: BPALogin v2.0.2 - portable BigPond Broadband login client
Jan 1 11:00:17 bpalogin[110]: Cant connect to auth server - No route to host
Jan 1 11:00:17 bpalogin[110]: Sleeping for 60 seconds
Jan 1 11:00:21 dnsmasq[51]: DHCPINFORM(br0) 192.168.1.87 00:10:dc:e8:25:6f
Jan 1 11:00:21 dnsmasq[51]: DHCPACK(br0) 192.168.1.87 00:10:dc:e8:25:6f beastylappy
Jan 1 11:00:22 udhcpc[109]: Received DHCP NAK
Jan 1 11:00:22 dnsmasq[51]: read /etc/hosts - 4 addresses
Jan 1 11:00:22 dnsmasq[51]: reading /tmp/resolv.conf
Jan 1 11:00:22 dnsmasq[51]: using nameserver 61.9.128.15#53
Jan 1 11:00:22 bpalogin[110]: Error connecting logout auth socket - Network is unreachable
Jan 1 11:00:22 dhcp client: nak: lease is lost
Jan 1 11:00:23 dnsmasq[51]: read /etc/hosts - 4 addresses
Jan 1 11:00:23 dnsmasq[51]: reading /tmp/resolv.conf
Jan 1 11:00:23 dnsmasq[51]: using nameserver 61.9.128.15#53
Jan 1 11:00:23 dhcp client: deconfig: lease is lost
Jan 1 11:00:23 ddns update: error connecting to members.dyndns.org:80
Jan 1 11:00:24 dnsmasq[51]: DHCPINFORM(br0) 192.168.1.87 00:10:dc:e8:25:6f
Jan 1 11:00:24 dnsmasq[51]: DHCPACK(br0) 192.168.1.87 00:10:dc:e8:25:6f beastylappy
Jan 1 11:00:26 udhcpc[109]: Entering released state
Jan 1 11:02:14 wan: connected manually
Jan 1 11:02:14 udhcpc[109]: Performing a DHCP renew
Jan 1 11:02:16 udhcpc[109]: Lease of 144.132.41.152 obtained, lease time 3600
Jan 1 11:02:17 dnsmasq[51]: read /etc/hosts - 4 addresses
Jan 1 11:02:17 dnsmasq[51]: reading /tmp/resolv.conf
Jan 1 11:02:17 dnsmasq[51]: using nameserver 61.9.192.15#53
Jan 1 11:02:17 dnsmasq[51]: using nameserver 61.9.128.14#53
Jan 1 11:02:17 dnsmasq[51]: using nameserver 61.9.128.15#53
Jan 1 11:02:17 ddns update: no update needed at this time
Jan 1 11:02:17 bpalogin[161]: BPALogin v2.0.2 - portable BigPond Broadband login client
Jan 1 11:02:17 dhcp client: bound IP : 144.132.41.152 from 144.132.40.1
Feb 18 16:01:12 ntp client: Synchronizing time with time.nist.gov ...
Feb 18 16:28:28 wan: disconnected manually
Feb 18 16:28:28 udhcpc[109]: Unicasting a release of 144.132.41.152 to 172.18.17.80
Feb 18 16:28:28 dnsmasq[51]: read /etc/hosts - 4 addresses
Feb 18 16:28:28 dnsmasq[51]: reading /tmp/resolv.conf
Feb 18 16:28:28 dnsmasq[51]: using nameserver 61.9.128.15#53
Feb 18 16:28:28 bpalogin[161]: Error connecting logout auth socket - Network is unreachable
Feb 18 16:28:28 dhcp client: deconfig: lease is lost
Feb 18 16:28:28 udhcpc[109]: Entering released state
Feb 18 16:28:28 udhcpc[109]: Entering released state
Feb 18 16:28:31 wan: connected manually
Feb 18 16:28:31 udhcpc[109]: Performing a DHCP renew
Feb 18 16:28:33 udhcpc[109]: Lease of 144.132.41.152 obtained, lease time 3600
Feb 18 16:28:33 dnsmasq[51]: read /etc/hosts - 4 addresses
Feb 18 16:28:33 dnsmasq[51]: reading /tmp/resolv.conf
Feb 18 16:28:33 dnsmasq[51]: using nameserver 61.9.192.15#53
Feb 18 16:28:33 dnsmasq[51]: using nameserver 61.9.128.14#53
Feb 18 16:28:33 dnsmasq[51]: using nameserver 61.9.128.15#53
Feb 18 16:28:34 ddns update: no update needed at this time
Feb 18 16:28:35 dhcp client: bound IP : 144.132.41.152 from 144.132.40.1
Feb 18 16:28:35 bpalogin[196]: BPALogin v2.0.2 - portable BigPond Broadband login client
Feb 18 16:55:30 wan: disconnected manually
Feb 18 16:55:30 udhcpc[109]: Unicasting a release of 144.132.41.152 to 172.18.17.80
Feb 18 16:55:30 dnsmasq[51]: read /etc/hosts - 4 addresses
Feb 18 16:55:30 dnsmasq[51]: reading /tmp/resolv.conf
Feb 18 16:55:30 dnsmasq[51]: using nameserver 61.9.128.15#53
Feb 18 16:55:30 bpalogin[196]: Error connecting logout auth socket - Network is unreachable
Feb 18 16:55:31 dhcp client: deconfig: lease is lost
Feb 18 16:55:31 udhcpc[109]: Entering released state
Feb 18 16:55:31 udhcpc[109]: Entering released state
Feb 18 16:55:33 wan: connected manually
Feb 18 16:55:33 udhcpc[109]: Performing a DHCP renew
Feb 18 16:55:36 udhcpc[109]: Lease of 144.132.41.152 obtained, lease time 3600
Feb 18 16:55:36 dnsmasq[51]: read /etc/hosts - 4 addresses
Feb 18 16:55:36 dnsmasq[51]: reading /tmp/resolv.conf
Feb 18 16:55:36 dnsmasq[51]: using nameserver 61.9.192.15#53
Feb 18 16:55:36 dnsmasq[51]: using nameserver 61.9.128.14#53
Feb 18 16:55:36 dnsmasq[51]: using nameserver 61.9.128.15#53
Feb 18 16:55:36 ddns update: no update needed at this time
Feb 18 16:55:37 dhcp client: bound IP : 144.132.41.152 from 144.132.40.1
Feb 18 16:55:37 bpalogin[222]: BPALogin v2.0.2 - portable BigPond Broadband login client

Oleg

18-02-2005, 07:23

Wesleyrpg

18-02-2005, 08:20

While it is still running, could you please type "ps", I just want to know if bpalogin processes around.

ok....this may sound stupid....but how do i run "ps" ??? (i've forgotten, how to talk to the router using text commands)

do i ping the router? do i run telnet? more info please?

Thanks and sorry

Adam

Oleg

18-02-2005, 09:12

Use hidden admin page - Main_AdmStatus_Content.asp

britnet

18-02-2005, 09:16

ok....this may sound stupid....but how do i run "ps" ???

Use telnet

connect to the router

and type ps

Wesleyrpg

18-02-2005, 14:25

i done what you asked......ran telnet and connected to router....

(none) login: admin
Password:
[admin@(none) root]$ ps
PID Uid VmSize Stat Command
1 admin 652 S /sbin/init
2 admin SW [keventd]
3 admin SWN [ksoftirqd_CPU0]
4 admin SW [kswapd]
5 admin SW [bdflush]
6 admin SW [kupdated]
7 admin SW [mtdblockd]
38 admin 296 S telnetd
43 admin 448 S httpd eth1
47 admin 356 S syslogd -m 0 -O /tmp/syslog.log -S -l 7
48 admin 316 S klogd
51 nobody 476 S dnsmasq
53 admin 492 S nas /tmp/nas.lan.conf /tmp/nas.lan.pid lan
56 admin SW [khubd]
65 admin 272 S lpd
67 admin 248 S p9100d -f /dev/usb/lp0 0
69 admin 248 S p9101d -f /dev/printers/0 1
72 admin 360 S waveservermain
74 admin 368 S rcamdmain
82 admin 316 S infosvr br0
83 admin 436 S watchdog
86 admin 360 S ntp
109 admin 400 S udhcpc -i eth1 -p /var/run/udhcpc0.pid -s /tmp/udhcpc
222 admin 364 S bpalogin -c /tmp/bpalogin.conf
241 admin 364 S bpalogin -c /tmp/bpalogin.conf
274 admin 364 S bpalogin -c /tmp/bpalogin.conf
300 admin 364 S bpalogin -c /tmp/bpalogin.conf
310 admin 480 S upnp -D -L br0 -W eth1
312 admin 508 S -sh
313 admin 372 R ps
[admin@(none) root]$

Oleg

18-02-2005, 16:09

i done what you asked......ran telnet and connected to router....

Thank you, I will check on that.

Wesleyrpg

19-02-2005, 01:38

interestingly enough, i turned router off overnight, and turned it on this morning, and found bpalogin running twice, with the ps command.

just rebooted router again, and now bpalogin appears in the list only once!

it seems the longer the router is turned on, the more cases of bpalogin appear?

Wesleyrpg

19-02-2005, 02:03

More info for you.......no reponse from net....so i manually disconnected and reconnected....heres a log

Jan 1 11:00:13 bpalogin[102]: BPALogin v2.0.2 - portable BigPond Broadband login client
Jan 1 11:00:13 kernel: neg fail
Jan 1 11:00:16 bpalogin[102]: Cant connect to auth server - No route to host
Jan 1 11:00:16 bpalogin[102]: Sleeping for 60 seconds
Jan 1 11:00:22 udhcpc[101]: Received DHCP NAK
Jan 1 11:00:22 dnsmasq[51]: read /etc/hosts - 4 addresses
Jan 1 11:00:22 dnsmasq[51]: reading /tmp/resolv.conf
Jan 1 11:00:22 dnsmasq[51]: using nameserver 61.9.128.15#53
Jan 1 11:00:22 bpalogin[102]: Error connecting logout auth socket - Network is unreachable
Jan 1 11:00:22 dhcp client: nak: lease is lost
Jan 1 11:00:22 ddns update: error connecting to members.dyndns.org:80
Jan 1 11:00:22 dnsmasq[51]: read /etc/hosts - 4 addresses
Jan 1 11:00:22 dnsmasq[51]: reading /tmp/resolv.conf
Jan 1 11:00:22 dnsmasq[51]: using nameserver 61.9.128.15#53
Jan 1 11:00:23 dhcp client: deconfig: lease is lost
Jan 1 11:00:26 udhcpc[101]: Entering released state
Jan 1 11:00:56 wan: connected manually
Jan 1 11:00:56 udhcpc[101]: Performing a DHCP renew
Jan 1 11:00:58 udhcpc[101]: Lease of 144.132.41.152 obtained, lease time 20925
Jan 1 11:00:58 dnsmasq[51]: read /etc/hosts - 4 addresses
Jan 1 11:00:58 dnsmasq[51]: reading /tmp/resolv.conf
Jan 1 11:00:58 dnsmasq[51]: using nameserver 61.9.192.15#53
Jan 1 11:00:58 dnsmasq[51]: using nameserver 61.9.128.14#53
Jan 1 11:00:58 dnsmasq[51]: using nameserver 61.9.128.15#53
Jan 1 11:00:59 ddns update: no update needed at this time
Feb 19 12:27:20 bpalogin[136]: BPALogin v2.0.2 - portable BigPond Broadband login client
Feb 19 12:27:20 dhcp client: bound IP : 144.132.41.152 from 144.132.40.1
Feb 19 12:27:29 ntp client: Synchronizing time with time.nist.gov ...
Feb 19 12:28:05 login[145]: root login on `pts/0'
Feb 19 12:45:04 login[148]: root login on `pts/0'
Feb 19 12:54:13 wan: disconnected manually
Feb 19 12:54:13 udhcpc[101]: Unicasting a release of 144.132.41.152 to 172.18.17.80
Feb 19 12:54:13 dnsmasq[51]: read /etc/hosts - 4 addresses
Feb 19 12:54:13 dnsmasq[51]: reading /tmp/resolv.conf
Feb 19 12:54:13 dnsmasq[51]: using nameserver 61.9.128.15#53
Feb 19 12:54:13 bpalogin[136]: Error connecting logout auth socket - Network is unreachable
Feb 19 12:54:13 dhcp client: deconfig: lease is lost
Feb 19 12:54:13 udhcpc[101]: Entering released state
Feb 19 12:54:13 udhcpc[101]: Entering released state
Feb 19 12:54:16 wan: connected manually
Feb 19 12:54:16 udhcpc[101]: Performing a DHCP renew
Feb 19 12:54:19 udhcpc[101]: Lease of 144.132.41.152 obtained, lease time 3600
Feb 19 12:54:19 dnsmasq[51]: read /etc/hosts - 4 addresses
Feb 19 12:54:19 dnsmasq[51]: reading /tmp/resolv.conf
Feb 19 12:54:19 dnsmasq[51]: using nameserver 61.9.192.15#53
Feb 19 12:54:19 dnsmasq[51]: using nameserver 61.9.128.14#53
Feb 19 12:54:19 dnsmasq[51]: using nameserver 61.9.128.15#53
Feb 19 12:54:19 ddns update: no update needed at this time
Feb 19 12:54:20 dhcp client: bound IP : 144.132.41.152 from 144.132.40.1
Feb 19 12:54:20 bpalogin[171]: BPALogin v2.0.2 - portable BigPond Broadband login client

Good luck

Adam

Oleg

19-02-2005, 09:29

Check your PM.

AlexSuslov

20-02-2005, 08:50

Device: WLHDD
Firmware: 1.9.2.7-3c
Problem: No ftp

[admin@wl-hdd /]$ lsmod
Module Size Used by
usb-storage 62144 0 (unused)
sd_mod 13268 0 (unused)
scsi_mod 70176 1 [usb-storage sd_mod]
videodev 8304 0 (unused)
audio 50120 0 (unused)
soundcore 5280 0 [audio]
printer 12620 0 (unused)
usb-ohci 21764 0 (unused)
usbcore 77224 1 [usb-storage audio printer usb-ohci]
ipt_NETMAP 992 2
ip_nat_starcraft 2224 0 (unused)
wl 418352 0 (unused)
et 26976 0 (unused)
ide-disk 13524 0
ide-probe-mod 11468 0
ide-mod 109568 0 [ide-disk ide-probe-mod]

[admin@wl-hdd /]$ mount
/dev/root on / type squashfs (ro)
none on /dev type devfs (rw)
proc on /proc type proc (rw)
ramfs on /tmp type ramfs (rw)
usbfs on /proc/bus/usb type usbfs (rw)

Syslog part:
Jan 1 03:00:02 kernel: hda: IC25N040ATMR04-0, ATA DISK drive

I see hard disk not mount, but it present :(
What i must to do?
Alex

Oleg

20-02-2005, 19:08

Device: WLHDD
Firmware: 1.9.2.7-3c
Problem: No ftp

Alex, the problem is that my firmware does not mount your harddisk automatically, you will need to do it yourself using the post-boot script. The easiest way is to add these lines to it:

#!/bin/sh
nvram set usb_storage_device=1

This should trigger mounting your drive in 10 seconds and launching ftp/samba.

Wesleyrpg

22-02-2005, 13:02

What does the router do with OOB (Out of Band) packets?

I'm having problems getting any punkbuster game to work. I have tried router with and without firewall turned on? Does it ignore OOB's?

Thanks

Adam

kiboko

22-02-2005, 17:59

HI.

I have a problem with the router and the printer(hp deskjet 5652). In the past two days in the system log I get this info
Feb 22 16:03:55 kernel: lp_wait_ready timeout
Feb 22 16:03:55 kernel: lp_write timeout
Feb 22 16:04:00 kernel: lp_wait_ready timeout
Feb 22 16:04:00 kernel: lp_write timeout
Feb 22 16:04:05 kernel: lp_wait_ready timeout
Feb 22 16:04:05 kernel: lp_write timeout
Feb 22 16:04:10 kernel: lp_wait_ready timeout
Feb 22 16:04:10 kernel: lp_write timeout
Feb 22 16:04:15 kernel: lp_wait_ready timeout
Feb 22 16:04:15 kernel: lp_write timeout
Feb 22 16:04:20 kernel: lp_wait_ready timeout
Feb 22 16:04:20 kernel: lp_write timeout
Feb 22 16:04:25 kernel: lp_wait_ready timeout
Feb 22 16:04:25 kernel: lp_write timeout
Feb 22 16:04:30 kernel: lp_wait_ready timeout
Feb 22 16:04:30 kernel: lp_write timeout

When I turn on the printer she prints the latest printed document. It's in Raw port 9100, USB.
I've readed a similar problem in the previous fw version.
Any news about this?

My fw is 1.9.2.7-cr3c with wpa-psk my wan(2 asus and 1 toshiba) and lan has 3 laptops :D and 2 desktops.

Thanks.

Oleg

22-02-2005, 18:06

HI.

I have a problem with the router and the printer(hp deskjet 5652). In the past two days in the system log I get this info
According to your log you are trying to print via parallel port using either port 9101 or LPR.

kiboko

22-02-2005, 21:24

the printer is connected by usb, port 9100 in both asus laptops. No other laptop or desktop uses the printer.

kiboko

23-02-2005, 14:46

Problem solved. A friend of mine who also has a wl-500g and has configured his printer in parallel mode has come to my house with his laptop. I believe that was the reason why the router act like this. I've restarted the router and now everything is ok.
thanks.

freestuff

23-02-2005, 21:49

I Have a strange problem, I have to reset my AP sometimes. When I look with Netstumbler to my AP I see the following:
http://wl500g.info/attachment.php?attachmentid=329&stc=1
Does anyone have seen this before?

Oleg

23-02-2005, 21:56

I Have a strange problem, I have to reset my AP sometimes. When I look with Netstumbler to my AP I see the following:
Does anyone have seen this before?
Well, looks like corrupted packets. Also, the receive signal is too strong - -28dB - have you changed output power somehow or attached external antenna?

KO(c)Tik

23-02-2005, 22:14

Device: WL500g
Firmware: 1.9.2.7 CR3c
Problem: MPPE required, but kernel has no support :-(

I try to connect to ISP over VPN connection.

My options.pptp file:
-----------------------------------------
lock
noauth
nobsdcomp
nodeflate
require-mppe
-----------------------------------------

My peer file:
-----------------------------------------
name myname
remotename PPTP
ipparam quadra
file /etc/ppp/options.pptp
-----------------------------------------

Files pap-secret and chap-secret exists and are correct.

Adn I start my connection with command
pppd pty 'pptp 10.4.0.254 --nolaunchpppd' call quadra updetach

This that I see:
Using interface ppp0
Connect: ppp0 <--> /dev/pts/1
Warning - secret file /tmp/ppp/pap-secrets has world and/or group access
Warning - secret file /tmp/ppp/chap-secrets has world and/or group access
MPPE required, but kernel has no support.
Connection terminated.
:-(((

This string is from kernel log:
Jan 1 03:00:03 kernel: MPPE/MPPC encryption/compression module registered

Sorry for my bad English :-(

Oleg

23-02-2005, 22:27

This that I see:
Using interface ppp0
Connect: ppp0 <--> /dev/pts/1
Warning - secret file /tmp/ppp/pap-secrets has world and/or group access
Warning - secret file /tmp/ppp/chap-secrets has world and/or group access
MPPE required, but kernel has no support.
Connection terminated.
:-(((

This is not an 1.9.2.7-3c log - either you've not upgraded firmware, or it does not belong to wl500g at all. Is this peer (server) log?
1.9.2.7-3c supports MPPE/MPPC out of the box, no manual actions required at all - just select PPTP.

KO(c)Tik

23-02-2005, 23:30

This is not an 1.9.2.7-3c log - either you've not upgraded firmware, or it does not belong to wl500g at all. Is this peer (server) log?
1.9.2.7-3c supports MPPE/MPPC out of the box, no manual actions required at all - just select PPTP.

Sorry, can i speek russian with you? My english is to poore to discribe all my manipulations with this device :(

But i can say with 100%, that firmware is 1.9.2.7-3c. This text is not a log, this is what i see on my display, when i try to connect to my VPN server by executing the following command.
pppd pty 'pptp 10.4.0.254 --nolaunchpppd' call quadra updetach

In /tmp/syslog.log I find the following lines:
-----------------------------------------------------
Jan 1 03:11:20 pppd[280]: pppd 2.4.2 started by admin, uid 0
Jan 1 03:11:20 pppd[280]: Using interface ppp0
Jan 1 03:11:20 pppd[280]: Connect: ppp0 <--> /dev/pts/1
Jan 1 03:11:20 pptp[283]: anon log[main:pptp.c:243]: The synchronous pptp option is NOT activated
Jan 1 03:11:20 pptp[285]: anon log[ctrlp_rep:pptp_ctrl.c:243]: Sent control packet type is 1 'Start-Control-Connection-Request'
Jan 1 03:11:20 pptp[285]: anon log[ctrlp_disp:pptp_ctrl.c:721]: Received Start Control Connection Reply
Jan 1 03:11:20 pptp[285]: anon log[ctrlp_disp:pptp_ctrl.c:755]: Client connection established.
Jan 1 03:11:21 pppd[280]: Warning - secret file /tmp/ppp/pap-secrets has world and/or group access
Jan 1 03:11:21 pptp[285]: anon log[ctrlp_rep:pptp_ctrl.c:243]: Sent control packet type is 7 'Outgoing-Call-Request'
Jan 1 03:11:21 pptp[285]: anon log[ctrlp_disp:pptp_ctrl.c:841]: Received Outgoing Call Reply.
Jan 1 03:11:21 pppd[280]: Warning - secret file /tmp/ppp/chap-secrets has world and/or group access
Jan 1 03:11:21 pptp[285]: anon log[ctrlp_disp:pptp_ctrl.c:880]: Outgoing call established (call ID 0, peer's call ID 4480).
Jan 1 03:11:21 pppd[280]: MPPE required, but kernel has no support.
Jan 1 03:11:21 pppd[280]: Connection terminated.
Jan 1 03:11:21 pptp[283]: anon warn[decaps_hdlc:pptp_gre.c:197]: short read (-1): Input/output error
Jan 1 03:11:21 pptp[283]: anon warn[decaps_hdlc:pptp_gre.c:209]: pppd may have shutdown, see pppd log
Jan 1 03:11:21 pppd[280]: Exit.
Jan 1 03:11:21 pptp[285]: anon log[callmgr_main:pptp_callmgr.c:228]: Closing connection
Jan 1 03:11:21 pptp[285]: anon log[ctrlp_rep:pptp_ctrl.c:243]: Sent control packet type is 12 'Call-Clear-Request'
Jan 1 03:11:21 pptp[285]: anon log[pptp_read_some:pptp_ctrl.c:525]: read returned zero, peer has closed
Jan 1 03:11:21 pptp[285]: anon log[call_callback:pptp_callmgr.c:77]: Closing connection
------------------------------------------------------

Oleg

24-02-2005, 08:02

Sorry, can i speek russian with you? My english is to poore to discribe all my manipulations with this device :(

Sure, use private messages.

dejay

27-02-2005, 22:47

I have a problem with this firmware. It looks like that router doesn't connect to time.nist.gov (there is nothing in the log that says that it even tried to connect), so my time in the router is: Fri, 02 Jan 1970.

Another problem is the log:

Jan 2 05:08:34 kernel: DROPIN=ppp0 OUT= MAC= SRC=193.77.104.218 DST=193.77.85.194 LEN=48 TOS=0x00 PREC=0x00 TTL=124 ID=22543 DF PROTO=TCP SPT=2394 DPT=445 SEQ=1530047695 ACK=0 WINDOW=16384 RES=0x00 SYN URGP=0 OPT (0204058601010402)
Jan 2 05:08:35 kernel: DROPIN=ppp0 OUT= MAC= SRC=193.77.104.218 DST=193.77.85.194 LEN=48 TOS=0x00 PREC=0x00 TTL=124 ID=22545 DF PROTO=TCP SPT=2353 DPT=31337 SEQ=1526670527 ACK=0 WINDOW=16384 RES=0x00 SYN URGP=0 OPT (0204058601010402)
Jan 2 05:10:14 kernel: DROPIN=ppp0 OUT= MAC= SRC=193.77.50.193 DST=193.77.85.194 LEN=48 TOS=0x00 PREC=0x00 TTL=126 ID=8367 DF PROTO=TCP SPT=4320 DPT=445 SEQ=3019354163 ACK=0 WINDOW=64800 RES=0x00 SYN URGP=0 OPT (020405A001010402)
Jan 2 05:10:17 kernel: DROPIN=ppp0 OUT= MAC= SRC=193.77.50.193 DST=193.77.85.194 LEN=48 TOS=0x00 PREC=0x00 TTL=126 ID=8550 DF PROTO=TCP SPT=4320 DPT=445 SEQ=3019354163 ACK=0 WINDOW=64800 RES=0x00 SYN URGP=0 OPT (020405A001010402)
Jan 2 05:11:08 kernel: DROPIN=ppp0 OUT= MAC= SRC=193.77.50.193 DST=193.77.85.194 LEN=48 TOS=0x00 PREC=0x00 TTL=126 ID=12581 DF PROTO=TCP SPT=1999 DPT=445 SEQ=3111494455 ACK=0 WINDOW=64800 RES=0x00 SYN URGP=0 OPT (020405A001010402)
Jan 2 05:11:11 kernel: DROPIN=ppp0 OUT= MAC= SRC=193.77.50.193 DST=193.77.85.194 LEN=48 TOS=0x00 PREC=0x00 TTL=126 ID=12794 DF PROTO=TCP SPT=1999 DPT=445 SEQ=3111494455 ACK=0 WINDOW=64800 RES=0x00 SYN URGP=0 OPT (020405A001010402)
Jan 2 05:11:19 kernel: DROPIN=ppp0 OUT= MAC= SRC=194.165.127.182 DST=193.77.85.194 LEN=48 TOS=0x00 PREC=0x00 TTL=124 ID=4672 DF PROTO=TCP SPT=2864 DPT=445 SEQ=2690808095 ACK=0 WINDOW=16384 RES=0x00 SYN URGP=0 OPT (0204058601010402)
Jan 2 05:11:45 kernel: DROPIN=eth0 OUT= MAC=ff:ff:ff:ff:ff:ff:00:0a:e6:d0:cc:b4:08:00 SRC=0.0.0.0 DST=255.255.255.255 LEN=328 TOS=0x00 PREC=0x00 TTL=128 ID=2871 PROTO=UDP SPT=68 DPT=67 LEN=308
Jan 2 05:11:49 kernel: DROPIN=ppp0 OUT= MAC= SRC=193.77.230.16 DST=193.77.85.194 LEN=48 TOS=0x00 PREC=0x00 TTL=126 ID=63996 DF PROTO=TCP SPT=3848 DPT=139 SEQ=2361238481 ACK=0 WINDOW=16384 RES=0x00 SYN URGP=0 OPT (0204058601010402)
Jan 2 05:11:49 kernel: DROPIN=eth0 OUT= MAC=ff:ff:ff:ff:ff:ff:00:0a:e6:d0:cc:b4:08:00 SRC=0.0.0.0 DST=255.255.255.255 LEN=328 TOS=0x00 PREC=0x00 TTL=128 ID=3034 PROTO=UDP SPT=68 DPT=67 LEN=308
Jan 2 05:11:52 kernel: DROPIN=ppp0 OUT= MAC= SRC=193.77.230.16 DST=193.77.85.194 LEN=48 TOS=0x00 PREC=0x00 TTL=126 ID=64100 DF PROTO=TCP SPT=3848 DPT=139 SEQ=2361238481 ACK=0 WINDOW=16384 RES=0x00 SYN URGP=0 OPT (0204058601010402)
Jan 2 05:11:58 kernel: DROPIN=eth0 OUT= MAC=ff:ff:ff:ff:ff:ff:00:0a:e6:d0:cc:b4:08:00 SRC=0.0.0.0 DST=255.255.255.255 LEN=328 TOS=0x00 PREC=0x00 TTL=128 ID=3476 PROTO=UDP SPT=68 DPT=67 LEN=308
Jan 2 05:12:14 kernel: DROPIN=eth0 OUT= MAC=ff:ff:ff:ff:ff:ff:00:0a:e6:d0:cc:b4:08:00 SRC=0.0.0.0 DST=255.255.255.255 LEN=328 TOS=0x00 PREC=0x00 TTL=128 ID=4155 PROTO=UDP SPT=68 DPT=67 LEN=308
Jan 2 05:12:20 kernel: DROPIN=ppp0 OUT= MAC= SRC=193.77.113.136 DST=193.77.85.194 LEN=48 TOS=0x00 PREC=0x00 TTL=126 ID=24045 DF PROTO=TCP SPT=4764 DPT=445 SEQ=739160563 ACK=0 WINDOW=64800 RES=0x00 SYN URGP=0 OPT (020405A001010402)
Jan 2 05:12:23 kernel: DROPIN=ppp0 OUT= MAC= SRC=193.77.113.136 DST=193.77.85.194 LEN=48 TOS=0x00 PREC=0x00 TTL=126 ID=24073 DF PROTO=TCP SPT=4764 DPT=445 SEQ=739160563 ACK=0 WINDOW=64800 RES=0x00 SYN URGP=0 OPT (020405A001010402)
Jan 2 05:13:02 kernel: DROPIN=ppp0 OUT= MAC= SRC=193.77.43.49 DST=193.77.85.194 LEN=48 TOS=0x00 PREC=0x00 TTL=124 ID=27391 DF PROTO=TCP SPT=4105 DPT=445 SEQ=4064038337 ACK=0 WINDOW=16384 RES=0x00 SYN URGP=0 OPT (0204058601010402)
Jan 2 05:13:04 kernel: DROPIN=ppp0 OUT= MAC= SRC=193.77.43.49 DST=193.77.85.194 LEN=48 TOS=0x00 PREC=0x00 TTL=124 ID=28111 DF PROTO=TCP SPT=4105 DPT=445 SEQ=4064038337 ACK=0 WINDOW=16384 RES=0x00 SYN URGP=0 OPT (0204058601010402)
Jan 2 05:13:20 kernel: DROPIN=ppp0 OUT= MAC= SRC=193.77.19.230 DST=193.77.85.194 LEN=48 TOS=0x00 PREC=0x00 TTL=124 ID=31832 DF PROTO=TCP SPT=4215 DPT=445 SEQ=2151228714 ACK=0 WINDOW=16384 RES=0x00 SYN URGP=0 OPT (020405A001010402)
Jan 2 05:13:23 kernel: DROPIN=ppp0 OUT= MAC= SRC=193.77.19.230 DST=193.77.85.194 LEN=48 TOS=0x00 PREC=0x00 TTL=124 ID=32156 DF PROTO=TCP SPT=4215 DPT=445 SEQ=2151228714 ACK=0 WINDOW=16384 RES=0x00 SYN URGP=0 OPT (020405A001010402)
Jan 2 05:14:05 kernel: DROPIN=ppp0 OUT= MAC= SRC=81.23.250.167 DST=193.77.85.194 LEN=62 TOS=0x00 PREC=0x00 TTL=58 ID=50807 DF PROTO=UDP SPT=4246 DPT=1035 LEN=42
Jan 2 05:14:05 kernel: DROPIN=ppp0 OUT= MAC= SRC=81.23.250.167 DST=193.77.85.194 LEN=99 TOS=0x00 PREC=0x00 TTL=58 ID=50817 DF PROTO=UDP SPT=4246 DPT=1035 LEN=79
Jan 2 05:15:13 kernel: DROPIN=ppp0 OUT= MAC= SRC=220.135.85.189 DST=193.77.85.194 LEN=40 TOS=0x00 PREC=0x00 TTL=113 ID=11791 PROTO=TCP SPT=4662 DPT=2604 SEQ=0 ACK=620502954 WINDOW=0 RES=0x00 ACK RST URGP=0
Jan 2 05:16:50 kernel: DROPIN=ppp0 OUT= MAC= SRC=80.203.82.175 DST=193.77.85.194 LEN=48 TOS=0x00 PREC=0x00 TTL=110 ID=19516 DF PROTO=TCP SPT=65239 DPT=6406 SEQ=3520080491 ACK=0 WINDOW=16384 RES=0x00 SYN URGP=0 OPT (020405B401010402)
Jan 2 05:16:53 kernel: DROPIN=ppp0 OUT= MAC= SRC=80.203.82.175 DST=193.77.85.194 LEN=48 TOS=0x00 PREC=0x00 TTL=110 ID=19626 DF PROTO=TCP SPT=65239 DPT=6406 SEQ=3520080491 ACK=0 WINDOW=16384 RES=0x00 SYN URGP=0 OPT (020405B401010402)
Jan 2 05:16:59 kernel: DROPIN=ppp0 OUT= MAC= SRC=80.203.82.175 DST=193.77.85.194 LEN=48 TOS=0x00 PREC=0x00 TTL=110 ID=19809 DF PROTO=TCP SPT=65239 DPT=6406 SEQ=3520080491 ACK=0 WINDOW=16384 RES=0x00 SYN URGP=0 OPT (020405B401010402)
Jan 2 05:17:29 kernel: DROPIN=eth0 OUT= MAC=ff:ff:ff:ff:ff:ff:00:0a:e6:d0:cc:b4:08:00 SRC=0.0.0.0 DST=255.255.255.255 LEN=328 TOS=0x00 PREC=0x00 TTL=128 ID=17587 PROTO=UDP SPT=68 DPT=67 LEN=308
Jan 2 05:17:33 kernel: DROPIN=eth0 OUT= MAC=ff:ff:ff:ff:ff:ff:00:0a:e6:d0:cc:b4:08:00 SRC=0.0.0.0 DST=255.255.255.255 LEN=328 TOS=0x00 PREC=0x00 TTL=128 ID=17773 PROTO=UDP SPT=68 DPT=67 LEN=308
Jan 2 05:17:40 kernel: DROPIN=eth0 OUT= MAC=ff:ff:ff:ff:ff:ff:00:0a:e6:d0:cc:b4:08:00 SRC=0.0.0.0 DST=255.255.255.255 LEN=328 TOS=0x00 PREC=0x00 TTL=128 ID=18076 PROTO=UDP SPT=68 DPT=67 LEN=308
Jan 2 05:17:56 kernel: DROPIN=eth0 OUT= MAC=ff:ff:ff:ff:ff:ff:00:0a:e6:d0:cc:b4:08:00 SRC=0.0.0.0 DST=255.255.255.255 LEN=328 TOS=0x00 PREC=0x00 TTL=128 ID=18622 PROTO=UDP SPT=68 DPT=67 LEN=308
...
...
...

WHAT IS THIS???

I didn't get messages like this with the 1.8.2.1 firmware.

Oleg

28-02-2005, 06:49

WHAT IS THIS???

I didn't get messages like this with the 1.8.2.1 firmware.
This is your firewall log.

RoofCat

28-02-2005, 08:30

This is your firewall log.
I beileve that space was missed after DROP in sources, and DROPIN is a bit cryptic IMHO.

So it goes.
Roofcat

dAF2000

28-02-2005, 10:12

RoofCat

28-02-2005, 10:28

Looks like it was a problem with time.nist.gov last weekend. Since 3 am monday it returned to normal (at least as I see it).

So it goes.
Roofcat

max2950

28-02-2005, 11:52

Looks like it was a problem with time.nist.gov last weekend. Since 3 am monday it returned to normal (at least as I see it).

So it goes.
Roofcat

Yes had also some problems with this time server....
:confused:

a3xx

07-03-2005, 06:52

Hi,
i have first time problem with Client mode at ASUS. I have WL-500bv2 and I upload the firmware WL500bv2-1.9.2.7-3c.trx. But after login to web interface and go to Wireless>Advanced, then don't show the settings for client mode, only items: Hide SSID, Fragmentation Threshold, RTS Threshold, Beacon Interval.
In the Admin web console after command "nvram get nobr" I become answer "1" > is Ralink, but after command "wl status" I become answer "wl driver adapter not found".
I have total 4 ASUS in client mode set up, but this one with v2 modification doesn't work. Can you help me, please?

Oleg

08-03-2005, 19:44

I have total 4 ASUS in client mode set up, but this one with v2 modification doesn't work. Can you help me, please?
wl500bv2 units are not supported.

a3xx

09-03-2005, 04:24

wl500bv2 units are not supported.

Thanks, I changed it for WL-500g and works perfect.

Oleg

10-03-2005, 17:23

if i connect directly to my ISP without the Asus, i did not get any DNS Server Errors, i can connect to Ebay in my account.
with the CR3c i was not able to log in ebay.

strange
maybe ill tray again next week
Please check your PM.

Pirat

12-03-2005, 09:07

Hello!

How can I setup PPTP and get WAN-IP from DHCP?