PDA

Bekijk de volledige versie : USB WLHDD 1.9.2.7-8



wodnik7
25-02-2008, 21:06
Hallo,

meine schöne WL-HDD hat den USB getötet? Heute früh ahbe ich noch gedruckt, alles bestens. Nun wird nix am USB Port erkannt. Habe aber zwischenzeitlich auf die neue FW geupdatet. Ob es damit was zu tun haben kann? Habe aber auch bisschen konfiguriert (neu partitioniert etc.)

lsusb zeigt nur: Bus 001 Device 001: ID 0000:0000
also merkt er nicht, dass da was dranhängt:(

Oder habe ich sonstwie was verstellt? kann ich eigentlich nicht glauben...

Danke für jegliche Hilfe!


hier der dmesg-Ausguss, etwas dort beunruhigendes zu finden?:

modifications) #9 Sun Oct 28 11:52:04 MSK 2007
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 noinitrd init=/linuxrc console=ttyS0,115200
CPU: BCM4710 rev 0 pkg 0 at 125 MHz
!unable to setup serial console!
Calibrating delay loop... 82.94 BogoMIPS
Memory: 13804k/16384k available (1833k kernel code, 2580k reserved, 248k data, 72k init, 0k highmem)
Dentry cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
Checking for 'wait' instruction... unavailable.
POSIX conformance testing by UNIFIX
PCI: Initializing host
PCI: Fixing up bus 0
PCI: Fixing up bridge
PCI: Fixing up bus 1
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Journalled Block Device driver loaded
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
NTFS driver v1.1.22 [Flags: R/O]
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
HDLC line discipline: version $Revision$, maxframe=4096
N_HDLC line discipline registered.
loop: loaded (max 8 devices)
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MPPE/MPPC encryption/compression module registered
Amd/Fujitsu Extended Query Table v1.1 at 0x0040
Flash Id: Vendor: 0x00c2 Device: 0x00a7
Physically mapped flash: Swapping erase regions for broken CFI table.
number of CFI chips: 1
Flash device: 0x400000 at 0x1fc00000
Physically mapped flash: squashfs filesystem found at block 953
Creating 5 MTD partitions on "Physically mapped flash":
0x00000000-0x00040000 : "boot"
0x00040000-0x003f0000 : "linux"
0x000ee744-0x003f0000 : "rootfs"
0x003f0000-0x00400000 : "nvram"
0x003e0000-0x003f0000 : "flashfs"
sflash: chipcommon not found
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 2048)
Linux IP multicast router 0.06 plus PIM-SM
ip_conntrack version 2.1 (128 buckets, 1024 max) - 352 bytes per conntrack
ip_conntrack_pptp version 1.9 loaded
ip_nat_pptp version 1.5 loaded
ip_tables: (C) 2000-2002 Netfilter core team
ipt_time loading
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
IPv6 v0.8 for NET4.0
IPv6 over IPv4 tunneling driver
NET4: Ethernet Bridge 008 for NET4.0
802.1Q VLAN Support v1.7 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
FAT: bogus logical sector size 37120
FAT: bogus logical sector size 37120
NTFS: Unable to set blocksize 512.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 72k freed
Warning: unable to open an initial console.
Algorithmics/MIPS FPU Emulator v1.5
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PDC20265: IDE controller on PCI bus 01 dev 08
PCI: Enabling device 01:01.0 (0004 -> 0007)
PDC20265: chipset revision 2
PDC20265: not 100% native mode: will probe irqs later
PDC20265: ROM enabled at 0x000d0000
PDC20265: (U)DMA Burst Bit DISABLED Primary PCI Mode Secondary PCI Mode.
PDC20265: FORCING BURST BIT 0x00 -> 0x01 ACTIVE
ide0: BM-DMA at 0x0140-0x0147, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0x0148-0x014f, BIOS settings: hdc:pio, hdd:pio
hda: FUJITSU MHV2080AH, ATA DISK drive
IDE: While probing, found an IDE channel that is busy (hdc).
IDE: Probably, this means the drive hasn't spun up yet.
IDE: We'll wait for it to spin up (but no more than 30 seconds).
IDE: The IDE channel is not busy any more, so we can continue probing.
IDE: While probing, found an IDE channel that is busy (hdd).
IDE: Probably, this means the drive hasn't spun up yet.
IDE: We'll wait for it to spin up (but no more than 30 seconds).
IDE: The IDE channel is not busy any more, so we can continue probing.
IDE: While probing, found an IDE channel that is busy (hdd).
IDE: Probably, this means the drive hasn't spun up yet.
IDE: We'll wait for it to spin up (but no more than 30 seconds).
IDE: The IDE channel is not busy any more, so we can continue probing.
ide2: ports already in use, skipping probe
ide3: ports already in use, skipping probe
ide4: ports already in use, skipping probe
ide5: ports already in use, skipping probe
ide0 at 0x100-0x107,0x10a on irq 6
blk: queue c00243d8, I/O limit 4095Mb (mask 0xffffffff)
hda: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=155061/16/63, UDMA(100)
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3
eth0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 4.108.9.0
eth1: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 4.108.9.0
PCI: Enabling device 01:02.0 (0004 -> 0006)
eth2: Broadcom BCM4320 802.11 Wireless Controller 4.108.9.0
device wds0.1 entered promiscuous mode
device eth2 entered promiscuous mode
device wds0.2 entered promiscuous mode
device eth1 entered promiscuous mode
br0: port 4(eth1) entering learning state
br0: port 3(wds0.2) entering learning state
br0: port 2(eth2) entering learning state
br0: port 1(wds0.1) entering learning state
br0: port 4(eth1) entering forwarding state
br0: topology change detected, propagating
br0: port 3(wds0.2) entering forwarding state
br0: topology change detected, propagating
br0: port 2(eth2) entering forwarding state
br0: topology change detected, propagating
br0: port 1(wds0.1) entering forwarding state
br0: topology change detected, propagating
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-ohci.c: USB OHCI at membase 0xb8004000, IRQ 2
usb-ohci.c: usb-00:04.0, PCI device 14e4:4715
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb.c: registered new driver usblp
printer.c: v0.13: USB Printer Device Class driver
Linux video capture interface: v1.00
SCSI subsystem driver Revision: 1.00
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,2), internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Adding Swap: 500432k swap-space (priority -1)
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,3), internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
wds0.2: no IPv6 routers present
eth2: no IPv6 routers present
wds0.1: no IPv6 routers present
br0: no IPv6 routers present
eth1: no IPv6 routers present
VFS: Can't find ext3 filesystem on dev ide0(3,0).
MSDOS FS: Using codepage 950
MSDOS FS: IO charset cp950
FAT: bogus logical sector size 0
VFS: Can't find a valid FAT filesystem on dev 03:00.
FAT: freeing iocharset=cp950
FAT: bogus logical sector size 0
VFS: Can't find a valid FAT filesystem on dev 03:00.
VFS: Can't find ext3 filesystem on dev ide0(3,1).
MSDOS FS: Using codepage 950
MSDOS FS: IO charset cp950
FAT: bogus logical sector size 0
VFS: Can't find a valid FAT filesystem on dev 03:01.
FAT: freeing iocharset=cp950
FAT: bogus logical sector size 0
VFS: Can't find a valid FAT filesystem on dev 03:01.
[root@azuza root]$

WLAN-Fan
25-02-2008, 21:45
Hi,

welche neue FirmWare? Von Oleg? Wann kam die raus?

Gruß.

wodnik7
25-02-2008, 23:30
Hi,

welche neue FirmWare? Von Oleg? Wann kam die raus?

Gruß.

hallo, die 1.9.2.7-8. Ich habe nun aber den hdparm aus meiner post-boot entfernt, sodass die HDD nicht mehr schlafen gehen soll - und plötzlich findet er den Drucker wieder... Ich beobachte morgen nochmals alles, und gebe Euch dann bescheid.
danke vielmals!

wengi
26-02-2008, 07:38
Zieh den Drucker mal ab und steckt ihn wieder dran.
Poste den Log, der dadurch entstanden ist.

Um einen Defekt des Druckers / Treibers auszuschließen solltest Du mal einen USB Stick anschließen und das Log posten.

wengi

wodnik7
26-02-2008, 08:42
Zieh den Drucker mal ab und steckt ihn wieder dran.
Poste den Log, der dadurch entstanden ist.

Um einen Defekt des Druckers / Treibers auszuschließen solltest Du mal einen USB Stick anschließen und das Log posten.

wengi

Hallo,

habe antürlich das auch probiert, auch mit dem Stick - es hat sich nix gerührt, lsusb hat nix angezeigt. Nun aber geht es wieder - und ich habe wirklich keine Ahnung, warum.. ob das hdparm dafür verantwortlich gewesemn sein konnte? Ich glaueb es ja nicht..
Viele Grüße!

wengi
26-02-2008, 10:12
So ein Computer ist halt auch nur ein Mensch...