PDA

Bekijk de volledige versie : Fehler beim Booten



tuxianer
07-02-2008, 23:02
hallo,
in meinem Log sind besonders gegen Ende ein paar Fehler. Woran liegt das? Ist das was kritisches?

Jan 1 01:00:03 syslogd started: BusyBox v1.1.3
Jan 1 01:00:03 dhcp client: bound IP : 192.168.2.33 from 192.168.2.1
Jan 1 01:00:03 kernel: zone(0): 4096 pages.
Jan 1 01:00:03 kernel: zone(1): 0 pages.
Jan 1 01:00:03 kernel: zone(2): 0 pages.
Jan 1 01:00:03 kernel: Kernel command line: root=/dev/mtdblock2 noinitrd init=/linuxrc console=ttyS0,115200
Jan 1 01:00:03 kernel: CPU: BCM4710 rev 0 pkg 0 at 125 MHz
Jan 1 01:00:03 kernel: !unable to setup serial console!
Jan 1 01:00:03 kernel: Calibrating delay loop... 82.94 BogoMIPS
Jan 1 01:00:03 kernel: Memory: 13804k/16384k available (1833k kernel code, 2580k reserved, 248k data, 72k init, 0k highmem)
Jan 1 01:00:03 kernel: Dentry cache hash table entries: 2048 (order: 2, 16384 bytes)
Jan 1 01:00:03 kernel: Inode cache hash table entries: 1024 (order: 1, 8192 bytes)
Jan 1 01:00:03 kernel: Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Jan 1 01:00:03 kernel: Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Jan 1 01:00:03 kernel: Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
Jan 1 01:00:03 kernel: Checking for 'wait' instruction... unavailable.
Jan 1 01:00:03 kernel: POSIX conformance testing by UNIFIX
Jan 1 01:00:03 kernel: PCI: Initializing host
Jan 1 01:00:03 kernel: PCI: Fixing up bus 0
Jan 1 01:00:03 kernel: PCI: Fixing up bridge
Jan 1 01:00:03 kernel: PCI: Fixing up bus 1
Jan 1 01:00:03 kernel: Linux NET4.0 for Linux 2.4
Jan 1 01:00:03 kernel: Based upon Swansea University Computer Society NET3.039
Jan 1 01:00:03 kernel: Initializing RT netlink socket
Jan 1 01:00:03 kernel: Starting kswapd
Jan 1 01:00:03 kernel: Journalled Block Device driver loaded
Jan 1 01:00:03 kernel: devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
Jan 1 01:00:03 kernel: devfs: boot_options: 0x1
Jan 1 01:00:03 kernel: NTFS driver v1.1.22 [Flags: R/O]
Jan 1 01:00:03 kernel: pty: 256 Unix98 ptys configured
Jan 1 01:00:03 kernel: Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
Jan 1 01:00:03 kernel: HDLC line discipline: version $Revision$, maxframe=4096
Jan 1 01:00:03 kernel: N_HDLC line discipline registered.
Jan 1 01:00:03 kernel: loop: loaded (max 8 devices)
Jan 1 01:00:03 kernel: PPP generic driver version 2.4.2
Jan 1 01:00:03 kernel: PPP Deflate Compression module registered
Jan 1 01:00:03 kernel: PPP BSD Compression module registered
Jan 1 01:00:03 kernel: MPPE/MPPC encryption/compression module registered
Jan 1 01:00:03 kernel: Amd/Fujitsu Extended Query Table v1.1 at 0x0040
Jan 1 01:00:03 kernel: Flash Id: Vendor: 0x00c2 Device: 0x00a7
Jan 1 01:00:03 kernel: Physically mapped flash: Swapping erase regions for broken CFI table.
Jan 1 01:00:03 kernel: number of CFI chips: 1
Jan 1 01:00:03 kernel: Flash device: 0x400000 at 0x1fc00000
Jan 1 01:00:03 kernel: Physically mapped flash: squashfs filesystem found at block 953
Jan 1 01:00:03 kernel: Creating 5 MTD partitions on "Physically mapped flash":
Jan 1 01:00:03 kernel: 0x00000000-0x00040000 : "boot"
Jan 1 01:00:03 kernel: 0x00040000-0x003f0000 : "linux"
Jan 1 01:00:03 kernel: 0x000ee744-0x003f0000 : "rootfs"
Jan 1 01:00:03 kernel: 0x003f0000-0x00400000 : "nvram"
Jan 1 01:00:03 kernel: 0x003e0000-0x003f0000 : "flashfs"
Jan 1 01:00:03 kernel: sflash: chipcommon not found
Jan 1 01:00:03 kernel: NET4: Linux TCP/IP 1.0 for NET4.0
Jan 1 01:00:03 kernel: IP Protocols: ICMP, UDP, TCP, IGMP
Jan 1 01:00:03 kernel: IP: routing cache hash table of 512 buckets, 4Kbytes
Jan 1 01:00:03 kernel: TCP: Hash tables configured (established 1024 bind 2048)
Jan 1 01:00:03 kernel: Linux IP multicast router 0.06 plus PIM-SM
Jan 1 01:00:03 kernel: ip_conntrack version 2.1 (128 buckets, 1024 max) - 352 bytes per conntrack
Jan 1 01:00:03 kernel: ip_conntrack_pptp version 1.9 loaded
Jan 1 01:00:03 kernel: ip_nat_pptp version 1.5 loaded
Jan 1 01:00:03 kernel: ip_tables: (C) 2000-2002 Netfilter core team
Jan 1 01:00:03 kernel: ipt_time loading
Jan 1 01:00:03 kernel: NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Jan 1 01:00:03 kernel: IPv6 v0.8 for NET4.0
Jan 1 01:00:03 kernel: IPv6 over IPv4 tunneling driver
Jan 1 01:00:03 kernel: NET4: Ethernet Bridge 008 for NET4.0
Jan 1 01:00:03 kernel: 802.1Q VLAN Support v1.7 Ben Greear <greearb@candelatech.com>
Jan 1 01:00:04 kernel: All bugs added by David S. Miller <davem@redhat.com>
Jan 1 01:00:04 kernel: FAT: bogus logical sector size 37120
Jan 1 01:00:04 kernel: FAT: bogus logical sector size 37120
Jan 1 01:00:04 kernel: NTFS: Unable to set blocksize 512.
Jan 1 01:00:04 kernel: VFS: Mounted root (squashfs filesystem) readonly.
Jan 1 01:00:04 kernel: Mounted devfs on /dev
Jan 1 01:00:04 kernel: Freeing unused kernel memory: 72k freed
Jan 1 01:00:04 kernel: Warning: unable to open an initial console.
Jan 1 01:00:04 kernel: Algorithmics/MIPS FPU Emulator v1.5
Jan 1 01:00:04 kernel: Uniform Multi-Platform E-IDE driver Revision: 6.31
Jan 1 01:00:04 kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Jan 1 01:00:04 kernel: PDC20265: IDE controller on PCI bus 01 dev 08
Jan 1 01:00:04 kernel: PCI: Enabling device 01:01.0 (0004 -> 0007)
Jan 1 01:00:04 kernel: PDC20265: chipset revision 2
Jan 1 01:00:04 kernel: PDC20265: not 100% native mode: will probe irqs later
Jan 1 01:00:04 kernel: PDC20265: ROM enabled at 0x000d0000
Jan 1 01:00:04 kernel: PDC20265: (U)DMA Burst Bit DISABLED Primary PCI Mode Secondary PCI Mode.
Jan 1 01:00:04 kernel: 5: FORCING BURST BIT 0x00 -> 0x01 ACTIVE
Jan 1 01:00:04 kernel: ide0: BM-DMA at 0x0140-0x0147, BIOS settings: hda:DMA, hdb:DMA
Jan 1 01:00:04 kernel: ide1: BM-DMA at 0x0148-0x014f, BIOS settings: hdc:DMA, hdd:pio
Jan 1 01:00:04 kernel: hda: SAMSUNG MP0402H, ATA DISK drive
Jan 1 01:00:04 kernel: ide2: ports already in use, skipping probe
Jan 1 01:00:04 kernel: ide3: ports already in use, skipping probe
Jan 1 01:00:04 kernel: ide4: ports already in use, skipping probe
Jan 1 01:00:04 kernel: ide5: ports already in use, skipping probe
Jan 1 01:00:04 kernel: ide0 at 0x100-0x107,0x10a on irq 6
Jan 1 01:00:04 kernel: blk: queue c00243d8, I/O limit 4095Mb (mask 0xffffffff)
Jan 1 01:00:04 kernel: hda: 78242976 sectors (40060 MB) w/8192KiB Cache, CHS=4870/255/63, UDMA(100)
Jan 1 01:00:04 kernel: Partition check:
Jan 1 01:00:04 kernel: /dev/ide/host0/bus0/target0/lun0: p1 p2 p3
Jan 1 01:00:04 kernel: eth0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 4.108.9.0
Jan 1 01:00:04 kernel: eth1: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 4.108.9.0
Jan 1 01:00:04 kernel: PCI: Enabling device 01:02.0 (0004 -> 0006)
Jan 1 01:00:04 kernel: eth2: Broadcom BCM4320 802.11 Wireless Controller 4.108.9.0
Jan 1 01:00:04 kernel: device eth2 entered promiscuous mode
Jan 1 01:00:04 kernel: device eth1 entered promiscuous mode
Jan 1 01:00:04 kernel: br0: port 2(eth1) entering learning state
Jan 1 01:00:04 kernel: br0: port 1(eth2) entering learning state
Jan 1 01:00:04 kernel: br0: port 2(eth1) entering forwarding state
Jan 1 01:00:04 kernel: br0: topology change detected, propagating
Jan 1 01:00:04 kernel: br0: port 1(eth2) entering forwarding state
Jan 1 01:00:04 kernel: br0: topology change detected, propagating
Jan 1 01:00:04 kernel: usb.c: registered new driver usbdevfs
Jan 1 01:00:04 kernel: usb.c: registered new driver hub
Jan 1 01:00:05 kernel: usb-ohci.c: USB OHCI at membase 0xb8004000, IRQ 2
Jan 1 01:00:05 kernel: usb-ohci.c: usb-00:04.0, PCI device 14e4:4715
Jan 1 01:00:05 kernel: usb.c: new USB bus registered, assigned bus number 1
Jan 1 01:00:05 kernel: hub.c: USB hub found
Jan 1 01:00:05 kernel: hub.c: 2 ports detected
Jan 1 01:00:06 kernel: usb.c: registered new driver usblp
Jan 1 01:00:06 kernel: printer.c: v0.13: USB Printer Device Class driver
Jan 1 01:00:06 kernel: Linux video capture interface: v1.00
Jan 1 01:00:07 kernel: SCSI subsystem driver Revision: 1.00
Jan 1 01:00:09 kernel: Initializing USB Mass Storage driver...
Jan 1 01:00:09 kernel: usb.c: registered new driver usb-storage
Jan 1 01:00:09 kernel: USB Mass Storage support registered.
Jan 1 01:00:11 kernel: Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Jan 1 01:00:11 portmap[77]: user rpc not found, reverting to user bin
Jan 1 01:00:12 statd[79]: Version 1.0.7 Starting
Jan 1 01:00:12 statd[79]: statd running as root. chown /var/lib/nfs/sm to choose different user
Jan 1 01:00:14 kernel: kjournald starting. Commit interval 5 seconds
Jan 1 01:00:14 kernel: EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
Jan 1 01:00:14 kernel: EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,2), internal journal
Jan 1 01:00:14 kernel: EXT3-fs: recovery complete.
Jan 1 01:00:14 kernel: EXT3-fs: mounted filesystem with ordered data mode.
Jan 1 01:00:14 kernel: Adding Swap: 506008k swap-space (priority -1)
Jan 1 01:00:14 kernel: kjournald starting. Commit interval 5 seconds
Jan 1 01:00:14 kernel: EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
Jan 1 01:00:14 kernel: EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,3), internal journal
Jan 1 01:00:14 kernel: EXT3-fs: recovery complete.
Jan 1 01:00:14 kernel: EXT3-fs: mounted filesystem with ordered data mode.


Viele Grüße tuxianer

tuxianer
07-02-2008, 23:02
Feb 7 23:44:06 kernel: VFS: Can't find ext3 filesystem on dev ide0(3,0).
Feb 7 23:44:06 kernel: MSDOS FS: Using codepage 950
Feb 7 23:44:06 kernel: MSDOS FS: IO charset cp950
Feb 7 23:44:06 kernel: FAT: bogus logical sector size 0
Feb 7 23:44:06 kernel: VFS: Can't find a valid FAT filesystem on dev 03:00.
Feb 7 23:44:06 kernel: FAT: freeing iocharset=cp950
Feb 7 23:44:06 kernel: FAT: bogus logical sector size 0
Feb 7 23:44:06 kernel: VFS: Can't find a valid FAT filesystem on dev 03:00.
Feb 7 23:44:06 kernel: VFS: Can't find ext3 filesystem on dev ide0(3,1).
Feb 7 23:44:06 kernel: MSDOS FS: Using codepage 950
Feb 7 23:44:06 kernel: MSDOS FS: IO charset cp950
Feb 7 23:44:06 kernel: FAT: bogus logical sector size 0
Feb 7 23:44:06 kernel: VFS: Can't find a valid FAT filesystem on dev 03:01.
Feb 7 23:44:06 kernel: FAT: freeing iocharset=cp950
Feb 7 23:44:06 kernel: FAT: bogus logical sector size 0
Feb 7 23:44:06 kernel: VFS: Can't find a valid FAT filesystem on dev 03:01.
Feb 7 23:44:17 ntp client: Synchronizing time with time.nist.gov ...

wengi
08-02-2008, 11:25
Hi,

die Dateisystemmeldungen kannst Du, abgesehen von den ext3, ignorieren.
Wenn Du Deine Platte mit ext3 formatiert hast, wonach es aussieht, kommen diese Fehler beim Laden der Treiber, da außer ext3 keine anderen Dateisysteme gefunden werden können.

EXT3-fs warning: maximal mount count reached, running e2fsck is recommendedDiese Meldung ist für ext3 bedingt normal. Ext3 zählt die Anzahl der mounts mit und meldet ab einer gewissen Grenze, dass es mal einen Check machen will.
Du kannst das auch ignorieren oder ein e2fsck durchführen.

wengi

tuxianer
08-02-2008, 12:28
Ok da muss ich mal suchen wie das fsck funktioniert. Aber was bedeutet z.B. das:
Feb 7 23:44:06 kernel: VFS: Can't find ext3 filesystem on dev ide0(3,0).