Bekijk de volledige versie : [HowTo] Install and configure Oleg's firmware
There is a prob with transmission.cgi hanging after loading some kb of the webinterface.
I didnt solve this until now because i have no idea where to start from.
If you use ctrl+c to exit lynx or close your browser the transmission.cgi is hanging and using 100% CPU.
killall transmission.cgi
will help...
wengi
PS: The download itself is working normaly...
Wengi,
Any update on the transmission issue?
L3rd
Ah well, I'm now totally on your script wengi:)
I still got some modified parts to keep it running in my way.
I also used the firmware scsi mod.
now I have only one problem, I can''t get my FTP to working because I mount part3 as /mnt
this was the original script to let the ftp work:
#Mount for ftp
mount /dev/discs/disc0/part2 /tmp/mnt/disc0_2
mount /dev/discs/disc0/part3 /tmp/mnt/disc0_3
now I have this configuration:
#device Mountpoint FStype Options Dump Pass#
/dev/discs/disc0/part1 none swap sw 0 0
/dev/discs/disc0/part2 /opt ext3 rw,noatime 1 1
/dev/discs/disc0/part3 /mnt ext3 rw,noatime 1 1
/dev/discs/disc0/part2 /tmp/mnt/disc0_2 ext3 rw,noatime 1 1
/dev/discs/disc0/part3 /tmp/mnt/disc0_3 ext3 rw,noatime 1 1
/dev/discs/disc1/part1 /tmp/mnt/disc1 ext3 rw,noatime 1 1
I expect to use the same options as the other mounts, but it''s not working
The mounting stops at /tmp/mnt/disc0_2.
so I get this:
Filesystem 1k-blocks Used Available Use% Mounted on
/dev/root 3072 3072 0 100% /
/dev/discs/disc0/part2 3850320 294316 3360416 8% /opt
/dev/discs/disc0/part3 476331024 118224836 333909892 26% /mnt
there should be 2 ways to solve this problem:
1 - get the mounts right
2 - make the vsftpd work on /mnt and /opt
the 2nd option is just a giant mystery for me how to do it:p
it must be some nvram... but how do you know witch:confused:
thanks wengi for the scripts, they are working better than the old ones:)
Hi,
check your fstab! Why do you mount to /mnt?
If you can give me a clean description of what you want to be mounted to where i can give you advice...
Normaly the fstab of my howto should be ok for your config.
I didn't try the ftp but maybe the ftpd will not follow the symlink /tmp/harddisk.
Try to change the rootdir in the ftp config in a second step.
wengi
EDIT: No news on transmission.
Hi,
check your fstab! Why do you mount to /mnt?
If you can give me a clean description of what you want to be mounted to where i can give you advice...
Normaly the fstab of my howto should be ok for your config.
I didn't try the ftp but maybe the ftpd will not follow the symlink /tmp/harddisk.
Try to change the rootdir in the ftp config in a second step.
wengi
EDIT: No news on transmission.
As far as I know the ftpd won't start as long no harddrives are mounted on /tmp/mnt
it's a value that can not be changed in the web admin as far as I know.
ok:
I want to mount the opt partition to: /opt and /tmp/mnt/disc0_2
the data partition to: /mnt and /tmp/mnt/disc0_3
I mount the data partition to /mnt because it's shorter (and I'm a bit lazy:p)
and I showed you my fstab in the previous post, I tought it should be done like that;)
Can you mount the partitions by hand?
Try to create the directories
/tmp/mnt/disc0_2
/tmp/mnt/disc0_3
/tmp/mnt/disc1
before mounting.
As far as i know using fstab the process itself should create the dirs before mounting, but maybe i am wrong or there is a bug...?!
wengi
after the disc check in pre-boot I have now 2 mkdirs to create both ftp dirs:)
then I have in fstab the mountpoints and it works:D
Filesystem 1k-blocks Used Available Use% Mounted on
/dev/root 3072 3072 0 100% /
/dev/discs/disc0/part2 3850320 541052 3113680 15% /opt
/dev/discs/disc0/part3 476331024 118551016 333583712 26% /mnt
/dev/discs/disc0/part2 3850320 541052 3113680 15% /tmp/mnt/disc0_2
/dev/discs/disc0/part3 476331024 118551016 333583712 26% /tmp/mnt/disc0_3
a bit stupid that I couldn''t figure the mkidir myself out:o
well, it totally works now:)
I do think it scans the drives double now, but hey, then you''re sure no errors are left;)
nunbaggi
28-05-2008, 20:45
I have a problem deleting what i download with transmission..
I need admin rights to do it.. How do i get this??
Hi,
I just finished setting up WL500gP V2 + HDD using Wengi's tutorial, great job.
It was the first time i was working with linux, but following this tutorial, i'm starting to understand how linux works, so thanks for that too.
Firmware: Oleg 1.9.2.7-10
Followed steps: 1, 2, 3, 4a, 4b, 5
on this step i got this:
admin@WL-500gP root]$ wget http://ipkg.nslu2-linux.org/feeds/optware/oleg/cross/stable/ipkg-opt_0.99.163-9_mipsel.ipk
Connecting to ipkg.nslu2-linux.org[140.211.169.169]:80
wget: server returned error 404: HTTP/1.1 404 Not Found
[admin@WL-500gP root]$ ipkg.sh install ipkg-opt_0.99.163-9_mipsel.ipk
File not found ipkg-opt_0.99.163-9_mipsel.ipk
don't know if it can cause any problems
when running ipkg list_installed, i get:
[admin@blechbuechse ipkg]$ ipkg list_installed
ipkg-opt - 0.99.149-2 - The Itsy Package Manager
uclibc-opt - 0.9.28-13
on this step it was the only error
next steps: 8, 9, 10a - no errors
Now, i select the torrent for download, i have it in "source" dir, "Push" in transmission, i have it as ACTIVE, but nothing happens:confused:
Whan the torrent is active, the window looks like this:
THE MENU
/opt/share/www/cgi-bin/transmission.cgi: kill: 9: (4000) - No such process
OOo_2.4.1rc1_20080523_SolarisSparc_install_en-US.tar.gz started Start: 29 May 00:12 Active status
Unable to find recent transfer stats in syslog
00:12:23 up 41 min, load average: 0.24, 0.13, 0.08
If I select "Info" i get:
Not a regular file (/tmp/harddisk/torrent/work/OOo_2.4.1rc1_20080523_SolarisSparc_install_en-US.tar.gz/OOo_2.4.1rc1_20080523_SolarisSparc_install_en-US.tar.gz.torrent)
Transmission 0.82 (r) - http://transmission.m0k.org/
Failed opening torrent file `/tmp/harddisk/torrent/work/OOo_2.4.1rc1_20080523_SolarisSparc_install_en-US.tar.gz/OOo_2.4.1rc1_20080523_SolarisSparc_install_en-US.tar.gz.torrent'
Not a regular file (/tmp/harddisk/torrent/work/OOo_2.4.1rc1_20080523_SolarisSparc_install_en-US.tar.gz/OOo_2.4.1rc1_20080523_SolarisSparc_install_en-US.tar.gz.torrent)
Maybe i did something wrong, the torrent is: OOo_2.4.1rc1_20080523_SolarisSparc_install_en-US.tar.gz.torrent, and it' working.
Thank you in advance!
PS: english is not my native language, so sorry for my writting mistakes :D
I have a problem deleting what i download with transmission..
I need admin rights to do it.. How do i get this??
what kind of windows do you use?
do you have guest account activated?:rolleyes:
@bogd_A
if you get a wget error, try it again, if you get it again, wait an hour, the server might be offline.
I don''t know if you continued to install everything, that''s why transmission might be acting weird.
note that due to some recent updates on transmission some strange behaviour happens to some ppl:)
what kind of windows do you use?
do you have guest account activated?:rolleyes:
@bogd_A
if you get a wget error, try it again, if you get it again, wait an hour, the server might be offline.
I don''t know if you continued to install everything, that''s why transmission might be acting weird.
note that due to some recent updates on transmission some strange behaviour happens to some ppl:)
still doesn't work - the server is ok
what do you mean by installing everything? as i said after step step 10a everything showld be ok, meaninig i should have a working system.
PS I started the tutorial from scratch ... and the same result :(
ipkg-opt was updated on 24.05.2008:
http://nslu2-linux.dyoung-mirror.net/feeds/optware/oleg/cross/stable/ipkg-opt_0.99.163-10_mipsel.ipk
I will update the HowTo.
wengi
Edit:
@bogd_A:
You are on an very old ipkg-opt installation now. Do again the wget and install stuff of ipkg-opt. Do a "ipkg update && ipkg upgrade" after this.
I hope this will switch you to the new repositories. This will also update your transmission to 1.21.
I have a problem deleting what i download with transmission..
I need admin rights to do it.. How do i get this??
Could you please give us a bit less information...?!?
You try to delete on which way? Samba, ftp, shell, webinterface?
If samba:
Would be nice to know which samba you are using, your config aso.
wengi
Edit:
@bogd_A:
You are on an very old ipkg-opt installation now. Do again the wget and install stuff of ipkg-opt. Do a "ipkg update && ipkg upgrade" after this.
I hope this will switch you to the new repositories. This will also update your transmission to 1.21
That was the problem, now everything works as it should, thank you for your support.
But there is one small issue: as said by nunbaggi, when trying to remove from the webinterface, a downloaded torrent, I get "Can only remove suspended torrents! Edit transmission.conf to FORCE_REMOVE. "
In transmission.conf - Force_remove is set to "YES"
The status of downloadet torrent is "DONE"
As for SAMBA it's enabled from the router's webinterface.
Firmware: 1.9.2.7-10
Regarding samba I have another issue, I can acces souce, targhet, work from a Vista OS, but when trying to acces it from XP OS, i get a logon box with user: WL-500/guest, and password :(
I am not using the Force_remove. I use ssh or samba.
And i do not have a torrent to test this atm.
But read the help (Help button in WIf).
I think you have to press purge and remove. But maybe i am wrong....
wengi
PS: http://www.nslu2-linux.org/wiki/Optware/Transmission
Hi.
I have a big prolem now.
Everything works fine until last evening.
Part2 become full. :(. This was for /otp...
Every process gives input/output error.
After restart this was in the log:
Jan 1 01:00:18 kernel: SCSI disk error : host 0 channel 0 id 0 lun 0 return code = 8000002
Jan 1 01:00:18 kernel: Current sd08:01: sns = 70 4
Jan 1 01:00:18 kernel: ASC=4b ASCQ= 0
Jan 1 01:00:18 kernel: Raw sense data:0x70 0x00 0x04 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x4b 0x00 0x00 0x00 0x00 0x00
Jan 1 01:00:18 kernel: I/O error: dev 08:01, sector 0
Jan 1 01:00:18 kernel: Adding Swap: 506008k swap-space (priority -1)
May 31 09:57:19 e2fsck: e2fsck: while trying to open /dev/discs/disc0/part2
May 31 09:57:19 e2fsck: /dev/discs/disc0/part2:
May 31 09:57:19 e2fsck: The superblock could not be read or does not describe a correct ext2
May 31 09:57:19 e2fsck: filesystem. If the device is valid and it really contains an ext2
May 31 09:57:19 e2fsck: filesystem (and not swap or ufs or something else), then the superblock
May 31 09:57:19 e2fsck: is corrupt, and you might try running e2fsck with an alternate superblock:
May 31 09:57:19 e2fsck: e2fsck -b 8193 <device>
May 31 09:57:19 kernel: SCSI disk error : host 0 channel 0 id 0 lun 0 return code = 8000002
May 31 09:57:19 kernel: Current sd08:03: sns = 70 4
May 31 09:57:19 kernel: ASC=4b ASCQ= 0
May 31 09:57:19 kernel: Raw sense data:0x70 0x00 0x04 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x4b 0x00 0x00 0x00 0x00 0x00
May 31 09:57:19 kernel: I/O error: dev 08:03, sector 0
May 31 09:57:19 kernel: SCSI disk error : host 0 channel 0 id 0 lun 0 return code = 8000002
May 31 09:57:19 kernel: Current sd08:03: sns = 70 4
May 31 09:57:19 kernel: ASC=4b ASCQ= 0
May 31 09:57:19 kernel: Raw sense data:0x70 0x00 0x04 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x4b 0x00 0x00 0x00 0x00 0x00
May 31 09:57:19 kernel: I/O error: dev 08:03, sector 2
May 31 09:57:19 e2fsck: e2fsck: while trying to open /dev/discs/disc0/part3
May 31 09:57:19 e2fsck: Could this be a zero-length partition?
May 31 09:57:19 kernel: SCSI disk error : host 0 channel 0 id 0 lun 0 return code = 8000002
May 31 09:57:19 kernel: Current sd08:01: sns = 70 4
May 31 09:57:19 kernel: ASC=4b ASCQ= 0
May 31 09:57:19 kernel: Raw sense data:0x70 0x00 0x04 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x4b 0x00 0x00 0x00 0x00 0x00
May 31 09:57:19 kernel: I/O error: dev 08:01, sector 0
May 31 09:57:19 kernel: SCSI disk error : host 0 channel 0 id 0 lun 0 return code = 8000002
May 31 09:57:19 kernel: Current sd08:01: sns = 70 4
May 31 09:57:19 kernel: ASC=4b ASCQ= 0
May 31 09:57:19 kernel: Raw sense data:0x70 0x00 0x04 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x4b 0x00 0x00 0x00 0x00 0x00
May 31 09:57:19 kernel: I/O error: dev 08:01, sector 8
May 31 09:57:19 kernel: SCSI disk error : host 0 channel 0 id 0 lun 0 return code = 8000002
May 31 09:57:19 kernel: Current sd08:02: sns = 70 4
May 31 09:57:19 kernel: ASC=4b ASCQ= 0
May 31 09:57:19 kernel: Raw sense data:0x70 0x00 0x04 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x4b 0x00 0x00 0x00 0x00 0x00
May 31 09:57:19 kernel: I/O error: dev 08:02, sector 0
May 31 09:57:19 kernel: SCSI disk error : host 0 channel 0 id 0 lun 0 return code = 8000002
May 31 09:57:19 kernel: Current sd08:03: sns = 70 4
May 31 09:57:19 kernel: ASC=4b ASCQ= 0
May 31 09:57:19 kernel: Raw sense data:0x70 0x00 0x04 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x4b 0x00 0x00 0x00 0x00 0x00
May 31 09:57:19 kernel: I/O error: dev 08:03, sector 2
May 31 09:57:19 kernel: EXT3-fs: unable to read superblock
What shuld I do now?
Thanks for your help in advance.
MrPeeth
Hi,
is /opt really full? Didnt think this is possible with ipkg packages. Or did you copy other stuff to /opt?
The other possibility is that the hdd has a prob. (e.g. bad sectors).
Did you try to use the alternative superblock?
wengi
I am not using the Force_remove. I use ssh or samba.
And i do not have a torrent to test this atm.
But read the help (Help button in WIf).
I think you have to press purge and remove. But maybe i am wrong....
wengi
PS: http://www.nslu2-linux.org/wiki/Optware/Transmission
The Torrents are in target dir, Remove (mark a torrent for removal) and Purge (delete the torrent and its file), can be used only for unfinished (suspended) torrents only, and that's why it didn't worked.
When I try to remove from samba I get: "You need permission to perform this action" - in VISTA OS
Can you tell me the command for delete using ssh?
And anothet issue:
I can't acces the torrent dir from a XP OS, only from Vista OS, can you help me?
In XP shows an logon window with use: WL-500gp\Guest, and password, nothing like this in Vista :confused:
shinji257
31-05-2008, 18:09
For dropbear I needed to satisfy the following requirements.
Disable password access for remote connections
Open port 443 and 2222 for remote connections (443 for when 2222 is blocked)
Allow password access on local connections
Don't open up port 22 for remote connections
I found that you can run multiple dropbear servers and they will co-exist. Here is how I set it up.
[shinji@WL-001E8C3E002C sbin]$ cat post-boot
#! /bin/sh
dropbear -P /var/run/dropbear-local.pid
[shinji@WL-001E8C3E002C sbin]$ cat post-mount
#! /bin/sh
dropbear -b /opt/etc/motd -g -p 2222 -P /var/run/dropbear-remote.pid
/opt/etc/init.d/rc.unslung start
The first is for post-boot. The only additional parameter here is -P which defines the pid file location. I renamed it otherwise the second one will overwrite the first rather than appending to it.
The second is post-mount. Note that it could of been put in post-boot as well but I put something into the command line that needs a file from the external device. I will explain each part.
-b defines a banner file to present before login finishes. It will be shown after the username is sent and before the password is requested. It is set to /opt/etc/motd right now so it is on the mounted device. This switch is optional and can be left out. If it is removed then it is save to move the whole remaining command-line to post-boot instead.
-g disables password logins for the "root" user
-s disables password logins globally (all users)
-p defines a port to listen to. You can use this parameter up to 10 times.
Note that the password-less login bit only affects that server. The one running on port 22 still accepts a password so I can still access it locally even if I lose my key.
EDIT: I should add that I recently added a user for the purpose of sftp access by a remote website. I change the original -s to -g. It will still prompt for a password but it will flat out deny it. My sftp user has /opt/libexec/sftp-server setup as the shell so right now ssh brings up a blank screen that they can do nothing at. You can change the -g (in bold above) to -s and it will deny all password logins for that server process.
EDIT: Here is an alternative to the above setup. This is one I have been using lately. The advantage here is that both servers are running immediately and you don't have to wait for the drive to mount for the external one to be usable.
[shinji@WL-001E8C3DFF31 sbin]$ cat post-boot
#! /bin/sh
dropbear -P /var/run/dropbear-local.pid
dropbear -s -p 2222 -P /var/run/dropbear-remote.pid -b /etc/banner
Note I used a banner that is in the /etc folder. To keep it persistent between reboots you have to make sure to save it as part of your flashfs (instructions in the main post) by adding it to your /usr/local/.files file.
Now the firewall...
[shinji@WL-001E8C3E002C sbin]$ cat post-firewall
#! /bin/sh
iptables -D INPUT -j DROP
iptables -t nat -A PREROUTING -i vlan1 -p tcp --dport 443 -j DNAT --to-destination 192.168.1.1:2222
iptables -t nat -A PREROUTING -i vlan1 -p tcp --dport 2222 -j DNAT --to-destination 192.168.1.1:2222
iptables -A INPUT -p tcp -m tcp -d 192.168.1.1 --dport 2222 -j ACCEPT
iptables -A INPUT -j DROP
I set it up so that ports 443 and 2222 would be externally accessable. Note that they both route to the same server running on port 2222. 443 is only there for cases where I need to route through a strict firewall that only allows http, https, and standard ssh connections. If you changed the port number in the command for the second server then replace 2222 with your port number. If you don't want port 443 open then remove the line in bold.
If you setup everything right then you will see the following when you run ps axf (if you installed procps)
[shinji@WL-001E8C3E002C root]$ ps axf
PID TTY STAT TIME COMMAND
1 ? S 0:01 /sbin/init
2 ? S 0:00 [keventd]
3 ? SN 1:07 [ksoftirqd_CPU0]
4 ? S 0:00 [kswapd]
5 ? S 0:00
6 ? S 0:00 [kupdated]
7 ? S 0:00 [mtdblockd]
58 ? S 0:00 telnetd
64 ? S 0:00 httpd vlan1
70 ? S 0:00 klogd
71 ? S 0:03 [dnsmasq]
73 ? Ss 0:00 nas /tmp/nas.lan.conf /tmp/nas.lan.pid lan
76 ? S 0:00 [khubd]
88 ? S 0:01 [usb-storage-0]
90 ? S 0:00 [scsi_eh_0]
114 ? Ss 0:00 watchdog
117 ? Ss 0:00 \_ ntp
116 ? S 0:00 radvd
[b] 124 ? S 0:00 dropbear -P /var/run/dropbear-local.pid
146 ? S 0:00 [kjournald]
147 ? S 0:00 [kjournald]
149 ? Ss 0:04 /usr/sbin/nmbd -D
151 ? Ss 0:00 /usr/sbin/smbd -D
155 ? S 0:00 dropbear -b /opt/etc/motd -s -p 2222 -P /var/run/dropbear-remote.pid
4238 ? Ss 0:00 \_ dropbear -b /opt/etc/motd -s -p 2222 -P /var/run/dropbear-remote.pid
4239 pts/0 Ss 0:00 \_ -sh
4242 pts/0 R+ 0:00 \_ ps axf
180 ? S 0:00 /sbin/syslogd -m 0 -O /opt/var/log/syslog.log -S -l 7 -s 0
186 ? Ss 0:00 /opt/sbin/cron
4176 ? S 0:00 upnp -D -L br0 -W vlan1
Note the 2 dropbear servers running.
Right now if someone accesses the router remotely then they will get the following.
compton:/home/shinji257> ssh -o Port=2222 shinji@xx.xx.xx.xx
..:: Elite Systems Remote SSH Access ::..
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
This is a restricted server.
Unauthorized access is strictly prohibited.
ALL CONNECTIONS ARE LOGGED.
Permission denied (publickey).
This would make it kinda fruitless to try to gain access that way unless there was an exploit for the dropbear server.
Hi Wengi!
Thx, 4 your answer.
"df" said that te part2is full.
I have discovered that transmission put temp datas there in /share/www dir.
the part3 seems to be working after 1 day OFF.
I turned on the hdd while router was was working.
Here is the log:
Jun 1 10:36:50 e2fsck: e2fsck: while trying to open /dev/discs/disc0/part2
Jun 1 10:36:50 e2fsck: /dev/discs/disc0/part2:
Jun 1 10:36:50 e2fsck: The superblock could not be read or does not describe a correct ext2
Jun 1 10:36:50 e2fsck: filesystem. If the device is valid and it really contains an ext2
Jun 1 10:36:50 e2fsck: filesystem (and not swap or ufs or something else), then the superblock
Jun 1 10:36:50 e2fsck: is corrupt, and you might try running e2fsck with an alternate superblock:
Jun 1 10:36:50 e2fsck: e2fsck -b 8193 <device>
Jun 1 10:36:50 e2fsck: /dev/discs/disc0/part3: recovering journal
Jun 1 10:37:33 kernel: SCSI disk error : host 0 channel 0 id 0 lun 0 return code = 8000002
Jun 1 10:37:33 kernel: Current sd08:03: sns = 70 4
Jun 1 10:37:33 kernel: ASC=4b ASCQ= 0
Jun 1 10:37:33 kernel: Raw sense data:0x70 0x00 0x04 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x4b 0x00 0x00 0x00 0x00 0x00
Jun 1 10:37:33 kernel: I/O error: dev 08:03, sector 8650752
Jun 1 10:37:34 kernel: SCSI disk error : host 0 channel 0 id 0 lun 0 return code = 8000002
Jun 1 10:37:34 kernel: Current sd08:03: sns = 70 4
Jun 1 10:37:34 kernel: ASC=4b ASCQ= 0
Jun 1 10:37:34 kernel: Raw sense data:0x70 0x00 0x04 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x4b 0x00 0x00 0x00 0x00 0x00
Jun 1 10:37:34 kernel: I/O error: dev 08:03, sector 24232
Jun 1 10:37:34 kernel: SCSI disk error : host 0 channel 0 id 0 lun 0 return code = 8000002
Jun 1 10:37:34 kernel: Current sd08:03: sns = 70 4
Jun 1 10:37:34 kernel: ASC=4b ASCQ= 0
Jun 1 10:37:34 kernel: Raw sense data:0x70 0x00 0x04 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x4b 0x00 0x00 0x00 0x00 0x00
Jun 1 10:37:34 kernel: I/O error: dev 08:03, sector 24234
Jun 1 10:37:34 kernel: SCSI disk error : host 0 channel 0 id 0 lun 0 return code = 8000002
Jun 1 10:37:34 kernel: Current sd08:03: sns = 70 4
Jun 1 10:37:34 kernel: ASC=4b ASCQ= 0
Jun 1 10:37:34 kernel: Raw sense data:0x70 0x00 0x04 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x4b 0x00 0x00 0x00 0x00 0x00
Jun 1 10:37:34 kernel: I/O error: dev 08:03, sector 24236
Jun 1 10:37:34 e2fsck: e2fsck: while reading block 3029
Jun 1 10:37:34 e2fsck: JBD: Failed to read block at offset 2495
Jun 1 10:37:34 e2fsck: JBD: IO error -5 recovering block 2495 in log
Jun 1 10:37:40 e2fsck: e2fsck: while recovering ext3 journal of /dev/discs/disc0/part3
Jun 1 10:37:40 kernel: kjournald starting. Commit interval 5 seconds
Jun 1 10:37:40 kernel: EXT3-fs warning: checktime reached, running e2fsck is recommended
Jun 1 10:37:40 kernel: EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,3), internal journal
Jun 1 10:37:40 kernel: EXT3-fs: recovery complete.
Jun 1 10:37:40 kernel: EXT3-fs: mounted filesystem with ordered data mode.
Jun 1 10:37:40 USB storage: ext3 fs at /dev/discs/disc0/part3 mounted to /tmp/mnt/disc0_3
Here is the info about the hdd now.
[admin@PSQ10 root]$ df
Filesystem 1k-blocks Used Available Use% Mounted on
/dev/root 3072 3072 0 100% /
/dev/discs/disc0/part3 152349444 133157204 11453328 92% /tmp/mnt/disc0_3
[admin@PSQ10 root]$ fdisk -l
Disk /dev/scsi/host0/bus0/target0/lun0/disc: 160.0 GB, 160041885696 bytes
255 heads, 63 sectors/track, 19457 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/scsi/host0/bus0/target0/lun0/part1 1 63 506016 82 Linux swap
/dev/scsi/host0/bus0/target0/lun0/part2 64 188 1004062+ 83 Linux
/dev/scsi/host0/bus0/target0/lun0/part3 189 19457 154778242+ 83 Linux
Now I have no access to part2, so I cannot check which dir is full.
[admin@PSQ10 root]$ vi /etc/fstab
#device Mountpoint FStype Options Dump Pass#
/dev/discs/disc0/part1 none swap sw 0 0
/dev/discs/disc0/part2 /opt ext3 rw,noatime 1 1
/dev/discs/disc0/part3 /tmp/harddisk ext3 rw,noatime 1 1
Part3 didn't mounted to where fstab describe. :(
I started my Linux with your tutorial, so can you help me in the alt. superblock or bad sector check?
FW vers.: 1.9.2.7-10
Thank:
MrPeeth
Hello everyone :)
@MrPeeth:
transmission should not put temp data to /opt !!! Please check your transmission.conf. What is your work-directory?
Regarding the superblock you should read your own post :)
May 31 09:57:19 e2fsck: is corrupt, and you might try running e2fsck with an alternate superblock:
May 31 09:57:19 e2fsck: e2fsck -b 8193 <device>You should try
e2fsck -b 8193 /dev/discs/disc0/part2BUT: If you can access your data atm: Do a backup! I think your hdd has a prob!
@shinji257:
Thanks for these tips. I will link it in the howto. I am NOT able to test it....
@bogd_A:
You can e.g. use the rm command in the shell:
rm -rf /tmp/harddisk/torrent/target/nameofyourtorrentdir
wengi
Hi Wengi!
I read errors every where that is why I did not discover the message...
This is the result:
login as: admin
admin@192.168.1.1's password:
[admin@PSQ10 root]$ e2fsck -b 8193 /dev/discs/disc0/part2
e2fsck 1.38 (30-Jun-2005)
e2fsck: while trying to open /dev/discs/disc0/part2
The superblock could not be read or does not describe a correct ext2
filesystem. If the device is valid and it really contains an ext2
filesystem (and not swap or ufs or something else), then the superblock
is corrupt, and you might try running e2fsck with an alternate superblock:
e2fsck -b 8193 <device>
[admin@PSQ10 root]$
The log growth with many error line coz e2fsck...
The workingdir for the transmission is:
/tmp/harddisk/torrent
I can read my datas on part3 in linux, except the /part2.
What do you think about this: delete part2, and start with a new partition and install all programs again?
or save all datas, format and test the whole disc? :eek:
Thank:
MrPeeth :confused:
shinji257
03-06-2008, 02:36
Hello everyone :)
@shinji257:
Thanks for these tips. I will link it in the howto. I am NOT able to test it....
Not a problem. I actually updated it a little. Mentioned what should be changed if they don't want to use port 2222 and/or 443 for the second server and also dropped in what ps should show if they installed procps. I put in bold a few key lines in the quoted areas.
Hi,
MrPeeth:
reformating and reinstalling part2 should be the fastest way.
But, as i said, i recommend a data backup. Maybe your hdd has a prob....
shinji257
thanks :)
wengi
nunbaggi
03-06-2008, 18:33
Originally Posted by nunbaggi
I have a problem deleting what i download with transmission..
I need admin rights to do it.. How do i get this??
Could you please give us a bit less information...?!?
You try to delete on which way? Samba, ftp, shell, webinterface?
If samba:
Would be nice to know which samba you are using, your config aso.
-I followed your how too all the way
-i can delete using ftp, or in my computer
-
MrPeeth:
reformating and reinstalling part2 should be the fastest way.
But, as i said, i recommend a data backup. Maybe your hdd has a prob....
Do you mean, only part2 need to be reformating?
Now I try to save all data on a winXP PC.
e2fsck program do bad sector test as well or there is an other linux program what I have to use for test my HDD?
Thanks:
MrPeeth
yep, only part2.
man e2fsck
-> e2fsck -ck /dev/dis.....
wengi
yep, only part2.
man e2fsck
-> e2fsck -ck /dev/dis.....
wengi
Hi Wengi!
Thx for fast reply.
I run a linux recovery on part2.
There are torrent datas in : /opt/share/cgi-bin
There are many files over 40Mb-s. Do I had any wrong settings? That is why my part2 become.
The donloaded torrents are in /tmp/harddisk/torrent/work directory, normally.
I will try to run the bad sector test.
The man command is new for me as well. :o
Thx again:
MrPeeth
add:
the really big file was: /opt/var/log/message.0 -> 7847Mb
Any idea? :)
Now I cannot find the part3 in the partiton table...
:(
Hi,
The growing of messages is the result of mixing scripts from my old and new howto.
Make sure that your files in /opt/etc/init.d/ are exactly as in my howto.
If you use an old syslog rc script it will grow your messages file until /opt is full....
If you saved all your data it would be the best to start all over again.
wengi
Hi,
The growing of messages is the result of mixing scripts from my old and new howto.
Make sure that your files in /opt/etc/init.d/ are exactly as in my howto.
If you use an old syslog rc script it will grow your messages file until /opt is full....
If you saved all your data it would be the best to start all over again.
wengi
Thx!
Now part2 is succesfully recovered.
But, part3 cannot discover by any windows prog. :(
Linux can detect part3 with wrong superblock...
I have some important datas on that partition, so I try to make some more step to save them.
Do you have any idea?
The part3 is almost 150Gb and it was nearly full.
Norton Partition manager said: unpartitionad area. :(
Ext2FSD discover a partition, but it cannot mount to Vista
I made it like you wrote so it is an ext3 partition, isn't it?
Thanks for all help.
MrPeeth
Yes, it is ext3.
But you normaly use ext2 tools because ext3 = ext2 + journal.
Do some google search for "ext3 recover superblock".
As far as i know ext3 saves various superblocks at differentlocations...
i am not that experienced with file systems...
wengi
Yes, it is ext3.
But you normaly use ext2 tools because ext3 = ext2 + journal.
Do some google search for "ext3 recover superblock".
As far as i know ext3 saves various superblocks at differentlocations...
i am not that experienced with file systems...
wengi
Thanks all.
I will try that you offered. :)
MrPeeth
nunbaggi
06-06-2008, 08:19
I have changed my firmware on wl-500w to the org asus 2.0.01 from oleg version 10.
I have installed Hdd with the guide 4a.
Now i cant find the HDD.
What are the folders called/partions on the HDD called??
What can i do?
Hi all gurus,
I applied lots of these configuration to my ASUS fw, what is done by engy from Czech Rep. due to the support for CDMA/HSDPA devices.
Everything works for me, I installed Samba3 and now I'm able to access it on the address of the router on a port 901, but have a serious problem with Transmission, which doesn't work at all.
I applied a step-by-step tutorial from this thread, but my Transmission is probably not running, see my output from "ps axf" below:
PID TTY STAT TIME COMMAND
1 ? S 0:01 /sbin/init
2 ? S 0:00 [keventd]
3 ? RN 0:02 [ksoftirqd_CPU0]
4 ? S 0:00 [kswapd]
5 ? S 0:00 [bdflush]
6 ? S 0:00 [kupdated]
7 ? S 0:00 [mtdblockd]
45 ? S 0:00 telnetd
50 ? S 0:03 httpd eth1
55 ? S 0:00 klogd
56 ? S 0:00 snmpd -c /tmp/snmpd.conf
60 ? S 0:00 [dnsmasq]
62 ? Ss 0:01 nas /tmp/nas.lan.conf /tmp/nas.lan.pid lan
65 ? S 0:00 [khubd]
74 ? Ss 0:00 lpd
76 ? Ss 0:00 p9100d -f /dev/usb/lp0 0
79 ? Ss 0:00 waveservermain
81 ? Ss 0:00 rcamdmain
85 ? S 0:00 [usb-storage-0]
86 ? S 0:00 [scsi_eh_0]
99 ? Ss 0:00 infosvr br0
100 ? Ss 0:00 watchdog
104 ? Ss 0:00 \_ ntp
113 ? S 0:00 dropbear
1132 ? Ss 0:01 \_ dropbear
1133 pts/1 Ss 0:00 \_ -sh
1218 pts/1 R+ 0:00 \_ ps axf
127 ? S 0:00 udhcpc -i eth1 -p /var/run/udhcpc0.pid -s /tmp/udhcpc
144 ? S 0:00 [kjournald]
145 ? S 0:00 [kjournald]
148 ? Ss 0:00 /usr/sbin/vsftpd
186 ? Ss 0:00 [smbd]
199 ? S 0:00 \_ [smbd]
1217 ? S 0:00 \_ [smbd]
188 ? Ss 0:00 /opt/sbin/nmbd -D -n rybarrouter -o -l /tmp -s /opt/etc/samba/smb.conf
193 ? Ss 0:00 /opt/sbin/cron
203 ? Ss 0:00 /opt/sbin/xinetd -pidfile /var/run/xinetd.pid
213 ? S 0:00 /usr/sbin/busybox_httpd -c /opt/etc/httpd.conf -p 8008 -h /opt/share/www
219 ? S 0:00 upnp -D -L br0 -W eth1
533 ? S 0:00 /sbin/syslogd -m 0 -O /opt/var/log/syslog.log -S -l 7 -s 0
Can anybody help me, where can be a problem?
@nunbaggi
i am not sure if the original firmware will accept the partitions made with oleg and my howto. No experience with this.
Maybe anyone else can help?
@Kubicz
Is the webinterface accessible?
If yes:
- Control if transmission is paused. If yes -> press pause button.
- Press watchdog button to start deamon
wengi
@nunbaggi
i am not sure if the original firmware will accept the partitions made with oleg and my howto. No experience with this.
Maybe anyone else can help?
@Kubicz
Is the webinterface accessible?
If yes:
- Control if transmission is paused. If yes -> press pause button.
- Press watchdog button to start deamon
wengi
Well, webinterface is accessible but there is an error:
Unable to find recent transfer stats in syslog
13:02:28 up 18 min, load average: 0.25, 0.67, 0.65
From ps I understood it that transmission is not running, so than I pressed pause button and result is:
touch: /.paused: Read-only file system /opt/share/www/cgi-bin/transmission.cgi: kill: 788: Usage: kill [-s sigspec | -signum | -sigspec] [pid | job]... or kill -l [exitstatus] Stopping transmissison!
Transmission will eventually stop. Last Log line should report transmissiond exiting.
Unable to find recent transfer stats in syslog
13:04:39 up 20 min, load average: 0.02, 0.43, 0.56
After pressing Watchdog it generates:
touch: /.watchdog: Read-only file system BusyBox v1.1.3 (2008.03.30-21:31+0000) multi-call binary Usage: rm [OPTION]... FILE... /opt/sbin/transmission_watchdog: kill: 304: Usage: kill [-s sigspec | -signum | -sigspec] [pid | job]... or kill -l [exitstatus] Usage: transmissiond [options] active-torrents.txt [options] Options: -h, --help Print this help and exit -v, --verbose Verbose level implies foreground (0 to 2, default = 0) -p, --port Port we should listen on (default = 51413) -u, --upload Maximum upload rate (-1 = no limit, default = 20) -d, --download Maximum download rate (-1 = no limit, default = -1) -f, --finish Command you wish to run on completion -n --nat-traversal Attempt NAT traversal using NAT-PMP or UPnP IGD -w, --watchdog Watchdog interval in seconds (default = 600) -i, --pidfile PID file path -e, --encryption Turns on encryption as preferred Signals: HUP reload active-torrents.txt and start/stop torrents USR1 write .status files into torrent directories USR2 list active torrents rm: cannot remove `/.watchdog': No such file or directory
13:06:14 up 21 min, load average: 0.07, 0.32, 0.50
Hi,
"Unable to find recent transfer stats in syslog" is normal if you didnt dl torrents before.
It seems that transmission can not write to the WORK directory.
Check permissions of the WORK directory and have a look at your syslog for errors.
wengi
Hi,
"Unable to find recent transfer stats in syslog" is normal if you didnt dl torrents before.
It seems that transmission can not write to the WORK directory.
Check permissions of the WORK directory and have a look at your syslog for errors.
wengi
Hi,
Thanks for a tools you proposed me.
First thing I haven't known before - OK than.
Work is configured through chmod, I did it by collective command: chmod -R ugoa+w /tmp/harddisk/torrent
In syslog (/opt/var/log/syslog.log) I have there errors:
Jun 6 10:25:34 xinetd[201]: Error parsing attribute user - DISABLING SERVICE [file=/opt/etc/xinetd.d/swat] [line=7]
But than I have no problem. At the end I've been posting log from last reboot after initializing DHCP server.
Jan 1 01:00:06 dnsmasq[60]: bad name at /etc/hosts line 3
Jan 1 01:00:06 dnsmasq[60]: read /etc/hosts - 7 addresses
Jan 1 01:00:06 dnsmasq[60]: read /etc/ethers - 2 addresses
Jan 1 01:00:06 dnsmasq[60]: reading /tmp/resolv.conf
Jan 1 01:00:06 kernel: usb.c: registered new driver usbdevfs
Jan 1 01:00:06 kernel: usb.c: registered new driver hub
Jan 1 01:00:06 kernel: usb-uhci.c: $Revision: 1.275 $ time 23:51:07 Mar 30 2008
Jan 1 01:00:06 kernel: usb-uhci.c: High bandwidth mode enabled
Jan 1 01:00:06 kernel: PCI: Enabling device 01:03.0 (0000 -> 0001)
Jan 1 01:00:06 kernel: ECHI PCI device 30381106 found.
Jan 1 01:00:06 kernel: UCHI reg 0x41 = 10
Jan 1 01:00:06 kernel: UCHI reg 0x41 changed to = 0
Jan 1 01:00:06 kernel: usb-uhci.c: USB UHCI at I/O 0x100, IRQ 12
Jan 1 01:00:06 kernel: usb-uhci.c: Detected 2 ports
Jan 1 01:00:06 kernel: usb.c: new USB bus registered, assigned bus number 1
Jan 1 01:00:06 kernel: Product: USB UHCI Root Hub
Jan 1 01:00:06 kernel: SerialNumber: 100
Jan 1 01:00:06 kernel: hub.c: USB hub found
Jan 1 01:00:06 kernel: hub.c: 2 ports detected
Jan 1 01:00:06 kernel: PCI: Enabling device 01:03.1 (0000 -> 0001)
Jan 1 01:00:06 kernel: ECHI PCI device 30381106 found.
Jan 1 01:00:06 kernel: UCHI reg 0x41 = 10
Jan 1 01:00:06 kernel: UCHI reg 0x41 changed to = 0
Jan 1 01:00:06 kernel: usb-uhci.c: USB UHCI at I/O 0x120, IRQ 12
Jan 1 01:00:06 kernel: usb-uhci.c: Detected 2 ports
Jan 1 01:00:07 kernel: usb.c: new USB bus registered, assigned bus number 2
Jan 1 01:00:07 kernel: Product: USB UHCI Root Hub
Jan 1 01:00:07 kernel: SerialNumber: 120
Jan 1 01:00:07 kernel: hub.c: USB hub found
Jan 1 01:00:07 kernel: hub.c: 2 ports detected
Jan 1 01:00:07 kernel: usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
Jan 1 01:00:07 kernel: PCI: Enabling device 01:03.2 (0000 -> 0002)
Jan 1 01:00:07 kernel: ehci_hcd 01:03.2: PCI device 1106:3104
Jan 1 01:00:07 kernel: ehci_hcd 01:03.2: irq 12, pci mem c0004000
Jan 1 01:00:07 kernel: usb.c: new USB bus registered, assigned bus number 3
Jan 1 01:00:07 kernel: ECHI PCI device 31041106 found.
Jan 1 01:00:07 kernel: ECHI reg 0x49 = 80010f20
Jan 1 01:00:07 kernel: ECHI reg 0x49 changed to = 80010f00
Jan 1 01:00:07 kernel: ECHI reg 0x4b = 80010f09
Jan 1 01:00:07 kernel: ECHI reg 0x4b changed to = 80010f29
Jan 1 01:00:07 kernel: PCI: 01:03.2 PCI cache line size set incorrectly (0 bytes) by BIOS/FW, correcting to 32
Jan 1 01:00:07 kernel: ehci_hcd 01:03.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4
Jan 1 01:00:07 kernel: Manufacturer: Linux 2.4.20 ehci_hcd
Jan 1 01:00:07 kernel: Product: PCI device 1106:3104
Jan 1 01:00:07 kernel: SerialNumber: 01:03.2
Jan 1 01:00:07 kernel: hub.c: USB hub found
Jan 1 01:00:07 kernel: hub.c: 4 ports detected
Jan 1 01:00:07 kernel: hub.c: connect-debounce failed, port 1 disabled
Jan 1 01:00:08 dnsmasq[60]: DHCPREQUEST(br0) 10.10.10.4 00:1d:e0:9c:e4:1f
Jan 1 01:00:08 dnsmasq[60]: DHCPACK(br0) 10.10.10.4 00:1d:e0:9c:e4:1f MCCK_Rybar
Jan 1 01:00:08 kernel: hub.c: new USB device 01:03.2-1, assigned address 2
Jan 1 01:00:08 kernel: Manufacturer: Western Digital
Jan 1 01:00:08 kernel: Product: External HDD
Jan 1 01:00:08 kernel: SerialNumber: 574341505A30363735393839
Jan 1 01:00:08 kernel: usb.c: USB device 2 (vend/prod 0x1058/0x910) is not claimed by any active driver.
Jan 1 01:00:08 kernel: Length = 18
Jan 1 01:00:08 kernel: DescriptorType = 01
Jan 1 01:00:08 kernel: USB version = 2.00
Jan 1 01:00:08 kernel: Vendor:Product = 1058:0910
Jan 1 01:00:08 kernel: MaxPacketSize0 = 64
Jan 1 01:00:08 kernel: NumConfigurations = 1
Jan 1 01:00:08 kernel: Device version = 1.06
Jan 1 01:00:08 kernel: Device Class:SubClass:Protocol = 00:00:00
Jan 1 01:00:08 kernel: Per-interface classes
Jan 1 01:00:08 kernel: Configuration:
Jan 1 01:00:08 kernel: bLength = 9
Jan 1 01:00:08 kernel: bDescriptorType = 02
Jan 1 01:00:08 kernel: wTotalLength = 0020
Jan 1 01:00:08 kernel: bNumInterfaces = 01
Jan 1 01:00:08 kernel: bConfigurationValue = 01
Jan 1 01:00:08 kernel: iConfiguration = 00
Jan 1 01:00:08 kernel: bmAttributes = c0
Jan 1 01:00:08 kernel: MaxPower = 2mA
Jan 1 01:00:08 kernel:
Jan 1 01:00:08 kernel: Interface: 0
Jan 1 01:00:08 kernel: Alternate Setting: 0
Jan 1 01:00:08 kernel: bLength = 9
Jan 1 01:00:08 kernel: bDescriptorType = 04
Jan 1 01:00:08 kernel: bInterfaceNumber = 00
Jan 1 01:00:08 kernel: bAlternateSetting = 00
Jan 1 01:00:08 kernel: bNumEndpoints = 02
Jan 1 01:00:08 kernel: bInterface Class:SubClass:Protocol = 08:06:50
Jan 1 01:00:08 kernel: iInterface = 00
Jan 1 01:00:08 kernel: Endpoint:
Jan 1 01:00:08 kernel: bLength = 7
Jan 1 01:00:08 kernel: bDescriptorType = 05
Jan 1 01:00:08 kernel: bEndpointAddress = 81 (in)
Jan 1 01:00:08 kernel: bmAttributes = 02 (Bulk)
Jan 1 01:00:08 kernel: wMaxPacketSize = 0200
Jan 1 01:00:08 kernel: bInterval = 00
Jan 1 01:00:08 kernel: Endpoint:
Jan 1 01:00:08 kernel: bLength = 7
Jan 1 01:00:08 kernel: bDescriptorType = 05
Jan 1 01:00:08 kernel: bEndpointAddress = 02 (out)
Jan 1 01:00:08 kernel: bmAttributes = 02 (Bulk)
Jan 1 01:00:08 kernel: wMaxPacketSize = 0200
Jan 1 01:00:08 kernel: bInterval = 00
Jan 1 01:00:09 kernel: usb.c: registered new driver usblp
Jan 1 01:00:09 kernel: printer.c: v0.13: USB Printer Device Class driver
Jan 1 01:00:10 kernel: usb.c: registered new driver audio
Jan 1 01:00:10 kernel: audio.c: v1.0.0:USB Audio Class driver
Jan 1 01:00:11 kernel: Linux video capture interface: v1.00
Jan 1 01:00:11 kernel: SCSI subsystem driver Revision: 1.00
Jan 1 01:00:11 kernel: Initializing USB Mass Storage driver...
Jan 1 01:00:11 kernel: usb.c: registered new driver usb-storage
Jan 1 01:00:11 kernel: scsi0 : SCSI emulation for USB Mass Storage devices
Jan 1 01:00:11 kernel: Vendor: WD Model: 3200AAJ External Rev: 1.06
Jan 1 01:00:11 kernel: Type: Direct-Access ANSI SCSI revision: 02
Jan 1 01:00:11 kernel: Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Jan 1 01:00:11 kernel: SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
Jan 1 01:00:11 kernel: Partition check:
Jan 1 01:00:13 dnsmasq[60]: DHCPINFORM(br0) 10.10.10.4 00:1d:e0:9c:e4:1f
Jan 1 01:00:13 dnsmasq[60]: DHCPACK(br0) 10.10.10.4 00:1d:e0:9c:e4:1f MCCK_Rybar
Jan 1 01:00:17 kernel: p1 p2 p3
Jan 1 01:00:17 kernel: USB Mass Storage support registered.
Jan 1 01:00:17 udhcpc[97]: udhcpc (v0.9.9-pre) started
Jan 1 01:00:18 dnsmasq[60]: bad name at /etc/hosts line 3
Jan 1 01:00:18 dnsmasq[60]: read /etc/hosts - 7 addresses
Jan 1 01:00:18 dnsmasq[60]: read /etc/ethers - 2 addresses
Jan 1 01:00:18 dnsmasq[60]: reading /tmp/resolv.conf
Jan 1 01:00:18 dhcp client: deconfig: lease is lost
Jan 1 01:00:18 kernel: usb.c: deregistering driver usblp
Jan 1 01:00:18 kernel: usb.c: deregistering driver audio
Jan 1 01:00:18 dropbear[114]: Running in background
Jan 1 01:00:20 udhcpc[97]: Lease of 172.20.1.8 obtained, lease time 86400
Jan 1 01:00:20 dnsmasq[60]: bad name at /etc/hosts line 3
Jan 1 01:00:20 dnsmasq[60]: read /etc/hosts - 7 addresses
Jan 1 01:00:20 dnsmasq[60]: read /etc/ethers - 2 addresses
Jan 1 01:00:20 dnsmasq[60]: reading /tmp/resolv.conf
Jan 1 01:00:20 dnsmasq[60]: using nameserver 172.20.1.1#53
Jan 1 01:00:22 dhcp client: bound IP : 172.20.1.8 from 172.20.1.1
Jan 1 01:00:28 kernel: Adding Swap: 506008k swap-space (priority -1)
Jun 6 15:53:21 e2fsck: /dev/discs/disc0/part2: recovering journal
Jun 6 15:53:21 e2fsck: /dev/discs/disc0/part2: clean, 9090/125696 files, 43390/251015 blocks
Jun 6 15:53:21 e2fsck: /dev/discs/disc0/part3: clean, 109/38895616 files, 5026592/77764640 blocks
Jun 6 15:53:21 kernel: kjournald starting. Commit interval 5 seconds
Jun 6 15:53:21 kernel: EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,2), internal journal
Jun 6 15:53:21 kernel: EXT3-fs: mounted filesystem with ordered data mode.
Jun 6 15:53:22 kernel: kjournald starting. Commit interval 5 seconds
Jun 6 15:53:22 kernel: EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,3), internal journal
Jun 6 15:53:22 kernel: EXT3-fs: mounted filesystem with ordered data mode.
Jun 6 15:53:22 USB storage: ext3 fs at /dev/discs/disc0/part3 mounted to /tmp/mnt/disc0_3
Jun 6 15:53:22 rc.unslung: start service /opt/etc/init.d/S05syslogd
Jun 6 15:53:22 System log daemon exiting.
Jun 6 15:53:24 syslogd started: BusyBox v1.1.3
Jun 6 15:53:24 syslogd: started.
Jun 6 15:53:24 rc.unslung: start service /opt/etc/init.d/S08samba
Jun 6 15:53:27 rc.unslung: start service /opt/etc/init.d/S10cron
Jun 6 15:53:27 /opt/sbin/cron[193]: (CRON) STARTUP (V5.0)
Jun 6 15:53:28 rc.unslung: start service /opt/etc/init.d/S10xinetd
Jun 6 15:53:28 rc.unslung: start service /opt/etc/init.d/S80busybox_httpd
Jun 6 15:53:28 xinetd[203]: xinetd Version 2.3.14 started with no options compiled in.
Jun 6 15:53:28 xinetd[203]: Started working: 1 available service
Jun 6 15:53:37 ntp client: Synchronizing time with time.nist.gov ...
Jun 6 15:57:58 dropbear[222]: password auth succeeded for 'kubicz' from 10.10.10.4:52442
Jun 6 16:00:01 /opt/sbin/cron[230]: (kubicz) CMD (nice transmission_watchdog)
Jun 6 16:00:07 transmission_watchdog: Transmission daemon restarted!
Another thing, if I click within the webinterface to log, it shows me:
sed: Empty filename
Creating graph...
/opt/share/www/cgi-bin/transmission.cgi: /opt/share/www/cgi-bin/transmission.cgi: 788: cannot create : Directory nonexistent
16:30:43 up 7 min, load average: 0.03, 0.05, 0.03
In bookmark "URL", there is a no box for filling a link.
I found an article on http://www.nslu2-linux.org/wiki/Optware/Transmission and problem might be cause because my root account is not "admin/root", but "kubicz". I was trying to find to change something in "transmission.cgi" but without result!
Hi,
The download speed is very low on my wl 500gp V2 with 1.9.2.7-10 firmware. I followed wengi's guide for setting up my sistem (asus + HDD).
the same torrent: on pc I get 137 - 152kb/s and 34 peers dl from 11 (using uTorrent) and on asus I get 9 - 15kb/s and 5 peers dl from 2.
another torrent: on PC 1,3 - 2Mb/s 1194 peers dl from 36, and on asus .... 11 peers dl from 1 at 6.6 kb/s
What am I missing?
shinji257
08-06-2008, 17:46
Another thing, if I click within the webinterface to log, it shows me:
sed: Empty filename
Creating graph...
/opt/share/www/cgi-bin/transmission.cgi: /opt/share/www/cgi-bin/transmission.cgi: 788: cannot create : Directory nonexistent
16:30:43 up 7 min, load average: 0.03, 0.05, 0.03
In bookmark "URL", there is a no box for filling a link.
I found an article on http://www.nslu2-linux.org/wiki/Optware/Transmission and problem might be cause because my root account is not "admin/root", but "kubicz". I was trying to find to change something in "transmission.cgi" but without result!
I have transmission setup without using admin for the username. Make sure to check the transmission_watchdog entry in the crontab file and change admin to your username. I also have transmission in a non-standard folder from the server so it doesn't appear to have anything hardcoded. It also worked fine downloading at 50KB/sec (I set that limit). The major thing I was concerned about is how the router would handle it. In the past I had issue with too many things running and torrents now so I didn't know how it would handle but it appears to have done fine last night.
Configuration:
IPv6 enabled (radvd is running)
Lighttpd server w/ php FCGI (eaccelerator enabled, 8080 external, 8081 internal)
2 SSH servers w/ SFTP (one internal -- one external)
Cron jobs
Transmission torrent client using Lighttpd for interface
A crap load of additional stuff including a, hopefully working, build environment. Memory is pretty much full but the system has been going over to swap as I had hoped.
The attached file is how I got cgi working in lighttpd (I know some had questions about it). Note that it only defines the .cgi extension. I assume that if you want to do .pl files as well you would install perl and add it to my file since it already enables mod_cgi. If you need additional information then you can always check the lighttpd docs @ http://trac.lighttpd.net/trac/wiki/Docs
I have transmission setup without using admin for the username. Make sure to check the transmission_watchdog entry in the crontab file and change admin to your username. I also have transmission in a non-standard folder from the server so it doesn't appear to have anything hardcoded. It also worked fine downloading at 50KB/sec (I set that limit). The major thing I was concerned about is how the router would handle it. In the past I had issue with too many things running and torrents now so I didn't know how it would handle but it appears to have done fine last night.
Configuration:
IPv6 enabled (radvd is running)
Lighttpd server w/ php FCGI (eaccelerator enabled, 8080 external, 8081 internal)
2 SSH servers w/ SFTP (one internal -- one external)
Cron jobs
Transmission torrent client using Lighttpd for interface
A crap load of additional stuff including a, hopefully working, build environment. Memory is pretty much full but the system has been going over to swap as I had hoped.
The attached file is how I got cgi working in lighttpd (I know some had questions about it). Note that it only defines the .cgi extension. I assume that if you want to do .pl files as well you would install perl and add it to my file since it already enables mod_cgi. If you need additional information then you can always check the lighttpd docs @ http://trac.lighttpd.net/trac/wiki/Docs
This was probably not a reply to my post, because I can't use anything you written down there.
My crontab contains raw:
*/30 * * * * kubicz nice transmission_watchdog, but by "ps" command I see no transmission process running.
Will not change my admin account from "kubicz" to "admin", because I had to change settings in many apps I have on my ASUS.
I am using default busybox_httpd instead of an additional lighthttpd.
shinji257
12-06-2008, 06:13
Your right. I must of been out of it that night. Anyways your crontab looks fine. It is working ok using a username other than admin for me as well. I actually run it in low priority too ( I won't go into detail). Here is the contents of the section of code that controls the log list.
# Show transfer log from log file
# Replace "transmissiond" with "transmission" if all logs are preferred
_log ()
{
if [ ! -r ${SYSLOG} ]; then
echo "<p>${SYSLOG} not readable. Properly configure syslogd at "
echo "system startup.</p>"
return
fi
echo "<pre>"
sed -n -e "/ transmission.*:/{s/.*: \([0-9]\{1,10\}\) [0-9]\{1,\} dl \([0-9.]\{1,\}\) ul \([0-9.]\{1,\}\) ld \([0-9.]\{1,\}\)/\1 \2 -\3 \4/;t data;p;b;:data w ${GNUPLOT_DATA}" -e "}" ${SYSLOG}
echo "</pre>"
if [ ! -x ${GNUPLOT} ]; then
echo "<p>gnuplot: ${GNUPLOT} not found. Properly configure paths "
echo "in transmission.conf for transfer graphing!</p>"
return
fi
echo "<p>Creating graph...</p>"
TZO=${TIMEZONE_OFFSET:-0}
cat > ${GNUPLOT_COMMAND} << __EOF__
set terminal png small size 800,320
set output '${GNUPLOT_OUTPUT}'
set xdata time
set timefmt "%s"
set format x "%H:%M\n%m/%d"
set ytics nomirror
set y2tics nomirror
set y2range [0:]
set ylabel "Transmission transfer rate [kB/s]"
set y2label "System load (5 min average)"
set y2tics 1
set xlabel "Time [UTC ${TZO} seconds]"
plot '${GNUPLOT_DATA}' using (\$1+86400+${TZO}):2 title 'download' axis x1y1 with impulses, \
'${GNUPLOT_DATA}' using (\$1+86400+${TZO}):3 title 'upload' with impulses, \
'${GNUPLOT_DATA}' using (\$1+86400+${TZO}):4 axis x1y2 title 'load' with lines
quit
__EOF__
${GNUPLOT} ${GNUPLOT_COMMAND}
echo "<img src=\"${HTTP_IMG_LOCATION}\">"
}
Note the lines in bold.
The first one calls sed and parses the system log. Looks like GNUPLOT_DATA may not be set. Also the same goes for the second one but instead referring to GNUPLOT_COMMAND. Give me a sec and I'll rig up the function with some debug lines to see what those settings are being recorded as. Maybe even show us the command lines that are being attempted.
EDIT: I've rigged up the _log() function with echo lines that will output the current value of the variables used in this function as well as the command lines as they are being executed. I did not bother to echo back the contents of the file that was being created yet. I can always add that. I did check and the file works fine even with these lines added.
Anyways backup your current copy of transmission.cgi and use the one that is attached instead. Try checking the Log area then copy and paste in the bolded lines in the file. These are the ones that I need to see what might be wrong.
P.S. - I could probably do this all over the place if I really wanted to. I kinda got used to the way the script is coded and can get around pretty easily now. Oleg did a good job organizing it.
shinji257
13-06-2008, 05:02
Ok guys. I am going to setup a secure openssh configuration similar to the dropbear one and I'll post the details here. Right off the bat you would want the following packages installed (plus dependencies).
openssh
openssh-sftp-server
scponly
I'll also cover doing a chroot configuration for scponly using scponlyc. I think I have the chroot environment already however it doesn't appear to work with dropbear. It drops the connection when it tries to chroot. :(
This is a directory listing of my chroot environment. In includes the vital items including their current working location. It was generated from my current tar archive that I will use to recreate it every time the router reboots. Currently it has dropbear instead of openssh in it. This will change once I have openssh working. The nice thing with openssh is that I should be able to re-create my current setup (2 ports -- 2 different configurations) with one sshd server and one sshd_config file. Hopefully.
drwxr-xr-x shinji/root 0 2008-06-12 20:43 bin/
lrwxrwxrwx shinji/root 0 2008-06-12 20:44 bin/rmdir -> busybox
lrwxrwxrwx shinji/root 0 2008-06-12 20:44 bin/rm -> busybox
lrwxrwxrwx shinji/root 0 2008-06-12 20:44 bin/mv -> busybox
lrwxrwxrwx shinji/root 0 2008-06-12 20:44 bin/mkdir -> busybox
lrwxrwxrwx shinji/root 0 2008-06-12 20:44 bin/ls -> busybox
lrwxrwxrwx shinji/root 0 2008-06-12 20:44 bin/ln -> busybox
lrwxrwxrwx shinji/root 0 2008-06-12 20:44 bin/chown -> busybox
lrwxrwxrwx shinji/root 0 2008-06-12 20:44 bin/chmod -> busybox
lrwxrwxrwx shinji/root 0 2008-06-12 20:44 bin/chgrp -> busybox
-rwxr-xr-x shinji/root 1291000 2008-06-12 20:43 bin/busybox
drwxr-xr-x shinji/root 0 2008-06-12 20:46 etc/
-rw-r--r-- shinji/root 33 2008-06-12 20:47 etc/group
-rw-r--r-- shinji/root 113 2008-06-12 20:47 etc/passwd
-rw-r--r-- shinji/root 23 2008-06-12 20:46 etc/ld.so.conf
-rw-r--r-- shinji/root 1097 2008-06-12 20:46 etc/ld.so.cache
drwxr-xr-x shinji/root 0 2008-06-12 20:51 lib/
-rwxr-xr-x shinji/root 5816 2008-06-12 21:02 lib/libutil.so.0
-rwxr-xr-x shinji/root 27108 2008-06-12 20:56 lib/ld-uClibc.so.0
-rwxr-xr-x shinji/root 501260 2008-06-12 20:56 lib/libc.so.0
-rwxr-xr-x shinji/root 84212 2008-06-12 20:56 lib/libm.so.0
-rwxr-xr-x shinji/root 14756 2008-06-12 20:56 lib/libcrypt.so.0
drwxr-xr-x shinji/root 0 2008-06-12 20:50 opt/
drwxr-xr-x shinji/root 0 2008-06-12 20:58 opt/lib/
-rwxr-xr-x shinji/root 27104 2008-06-12 21:01 opt/lib/ld-uClibc.so.0
-rw-r--r-- shinji/root 698368 2008-06-12 21:00 opt/lib/libc.so.0
-rw-r--r-- shinji/root 68368 2008-06-12 21:00 opt/lib/libgcc_s.so.1
-rw-r--r-- shinji/root 1628 2008-06-12 20:59 opt/lib/libresolv.so.0
-rw-r--r-- shinji/root 11552 2008-06-12 20:59 opt/lib/libcrypt.so.0
-rw-r--r-- shinji/root 76300 2008-06-12 20:59 opt/lib/libz.so
-rw-r--r-- shinji/root 4832 2008-06-12 20:59 opt/lib/libutil.so.0
-rw-r--r-- shinji/root 1386308 2008-06-12 20:58 opt/lib/libcrypto.so.0.9.7
drwxr-xr-x shinji/root 0 2008-06-12 20:50 opt/libexec/
-rwxr-xr-x shinji/root 60920 2008-06-12 20:50 opt/libexec/sftp-server
drwxr-xr-x shinji/root 0 2008-06-12 20:48 usr/
drwxr-xr-x shinji/root 0 2008-06-12 20:49 usr/sbin/
-rwxr-xr-x shinji/root 368448 2008-06-12 20:49 usr/sbin/dropbear
drwxr-xr-x shinji/root 0 2008-06-12 20:48 usr/bin/
lrwxrwxrwx shinji/root 0 2008-06-12 20:49 usr/bin/scp -> ../sbin/dropbear
There are alot of links there because of dropbear and busybox.
Hi,
transmission is not started directly after restart. It normaly depends on the cron entry. E.g. if the watchdog is started hourly, transmission will be started the next full hour after thr reboot.
If you want to start it directly after the reboot: Add transmission_watchdog to your post-boot.
Hi,
I have transmission_watchdog in post-boot, but it doesn't start after reboot :(
And some questions:
- If i have a power loss, when the power comes back againt, transmission won't start automaticaly, it is normal?
- Has Samba 2 (ipkg) has issues with VISTA?
- It is possible to have instead of "listening_port" somethink like "port_range", in transmission? I hope that in this way the download speed could increase, by accesing not only one defined port.
- What is the best way, and first the safest, for accesing files, stored on my hdd, attached on wl 500 gp, from wan?
Thank you
metamorphose
15-06-2008, 12:40
Hi Everybody,
I was tried to install Oleg custom firmware v1.9.2.7-10 on my WL-700gE, but I could not, always appears this error message:
"An error was detecting during the upgrade.
The firmware has NOT been succesfully changed."
What can cause this error?
Hi,
@metamorphose:
Never had this before. Make sure you have the right firmware and try the asus recovery tool.
@bogd_A:
- if watchdog is in post-boot and transmission is not paused: It should be started on reboot.
- As far as i know the newest samba2 works with vista. But i don't have vista.. But you could use the samba integrated with olegs -10 and up. He fixed the vista issues in the orig firm. see changelog.
- transmission uses only one port. As far as i know this is by design. oleo is your man for further questions.
- the most secure way is ssh/scp. Also sftp is secure. I use ssh and winscp from wan.
wengi
Hi,
@metamorphose:
Never had this before. Make sure you have the right firmware and try the asus recovery tool.
@bogd_A:
- if watchdog is in post-boot and transmission is not paused: It should be started on reboot.
- As far as i know the newest samba2 works with vista. But i don't have vista.. But you could use the samba integrated with olegs -10 and up. He fixed the vista issues in the orig firm. see changelog.
- transmission uses only one port. As far as i know this is by design. oleo is your man for further questions.
- the most secure way is ssh/scp. Also sftp is secure. I use ssh and winscp from wan.
wengi
I have watchdog in post-boot, it is not paused but won't start on reboot, I'll recheck when i'll get back home -
It will not start at reboot
As for samba, I like in samba 2 the feature of password protected folders, and this is what it is not working with VISTA, if i don't password protect folders it works, but on XP I can't acces shared folders, not with integrated samba or samba 2 - i get a logon window, with user: name_of_ASUS\guest - not editable and password: and nothing works.
It is a way of pasword protect folders using samba integrated in oleg's firmware, and do you have a solution for the XP acces?
About transmission, it is normal to do:
Jun 16 20:49:27 transmission_watchdog: Transmission daemon restarted!
Jun 16 20:00:10 transmission_watchdog: Transmission daemon restarted!
Jun 16 18:00:10 transmission_watchdog: Transmission daemon restarted!
Jun 16 14:00:10 transmission_watchdog: Transmission daemon restarted!
Jun 16 10:30:15 transmission_watchdog: Transmission daemon restarted!
but the roter wasn't restarted, and it wasn't the case of a power loss, after restart of transmission_watcdog i get Checking files ... and it takes a long time to do this.
And finaly about the speed in transmission, at upload I have speeds of 120 - 400kb/s (after setting UPLOAD_SPEED=41 I get 41kb/s - max for upload), but on download ... best was 40 - 50 kb/s (total) from 2 downloading torrents ... I don't know what to check :( any ideea?
in transmission.conf I have:
DOWNLOAD_SPEED=-1
UPLOAD_SPEED=41
ENCRIPTION=-e
my /usr/local/sbin/post-firewall looks like:
#!/bin/sh
## FIREWALL
## set default policy
iptables -P INPUT DROP
## deny ftp access from WAN
iptables -I INPUT 1 -p tcp -i "$1" --syn --dport 21 -j DROP
## Allow access to various router services from WAN
for P in 65534; do
iptables -I INPUT 1 -p tcp --syn -i "$1" --dport $P -j ACCEPT
done
And on ASUS web page, under NAT Setting - Virtual Server, I have at Virtual server list:
Port Range: 65534
Local IP: IP of ASUS
Local Port: 65534
Protocol: BOTH
Is anything wrong with this set-up, and what else should I do?
What the numbers of "20:30:26 up 21:28, load average: 3.56, 3.04, 2.55" means, what is cpu, mem ... load?
Can you help me with a how to, step by step config of ssh and winscp, if you have the time :)
Thank you
metamorphose
16-06-2008, 20:09
Hi wengi,
to tell the truth I must tell that kfurge custom firmware was on my router (I love it, however I am curious, that's why I would like to try Oleg's version). I had downgraded kfurge 1.0.4.6 to official 1.0.4.6, then I restarted router and tried to install Oleg's firmware. I am sure I downloaded it from right place: http://oleg.wl500g.info/1.9.2.7-10/WL700g-1.9.2.7-10.zip
On the other hand, I do not understand where is the relationship between firmware upgrade and post boot file, because error message appears almost directly after upgrade process starts (about 2-3 seconds).
@bogd_A:
Your transmission is fine. Checking files takes hours if you have big torrent files on the hdd. My transmission speed is always about 40k. never had it faster except "official" downloads.
I will not write a step-by-step howto. This is linux basics. You have to read and learn....
@all
ALWAYS REMEMBER: Your Asus is a Router and NOT a Pentium Core II Duo with 3GHz. THIS MACHINES ARE SLOW!!!
@metamorphose
Did you extract the zip?
wengi
shinji257
17-06-2008, 09:24
@all
ALWAYS REMEMBER: Your Asus is a Router and NOT a Pentium Core II Duo with 3GHz. THIS MACHINES ARE SLOW!!!
Amen! Anyways it is a miracle how much I got going on my router.
Full IPv6 support (radvd broadcasting IPv6 subnet)
Lighttpd w/ PHP using FastCGI and eAccelerator extension
Transmission
RRDTool (macsat.com setup)
2 x Dropbear servers w/ SFTP capability
Syslog Daemon (from ipkg)
Now then I do have Wordpress going on the server using a SQLite database (addon db support) and it works surprisingly well. Slow but well enough. I spec the router for the equivalent to an approx 8 year old computer. Not very fast but enough. I won't even attempt to push on a MySQL server. The swapfile works well. So well that even though the number of applications running well exceeds the available ram my router has kept on ticking.
metamorphose
17-06-2008, 18:01
@metamorphose
Did you extract the zip?
wengi
Yes, of course I did and I tried to upload TRX file, unsuccessfully. :confused:
HI,
I had to reconfig from scratch my WL-500gP V2 - HDD system.
Everything worked ok, using Wengi's tutorial, but after installing transmission, I had the first error.
Note that I set my sistem (WL-500gP V2 + HDD) two times before, and had no error.
at vi /opt/etc/crontab
I have:
SHELL=/bin/sh
PATH=/sbin:/bin:/usr/sbin:/usr/bin:/opt/sbin:/opt/bin
MAILTO=""
HOME=/
# ---------- ---------- Default is Empty ---------- ---------- #
On the firs two setups I had:
SHELL=/bin/sh
PATH=/sbin:/bin:/usr/sbin:/usr/bin:/opt/sbin:/opt/bin
MAILTO=""
HOME=/
# ---------- ---------- Default is Empty ---------- ---------- #
*/30 * * * * admin nice /opt/sbin/transmission_watchdog
This is the first difference.
The second error was:
[admin@WL-500gP root]$ transmission_watchdog
-sh: transmission_watchdog: not found
[admin@WL-500gP root]$
ps axf looks like this:
[admin@WL-500gP root]$ ps axf
PID TTY STAT TIME COMMAND
1 ? S 0:01 /sbin/init
2 ? S 0:00 [keventd]
3 ? SN 0:00 [ksoftirqd_CPU0]
4 ? S 0:00 [kswapd]
5 ? S 0:00 [bdflush]
6 ? S 0:00 [kupdated]
7 ? S 0:00 [mtdblockd]
57 ? S 0:00 telnetd
62 ? S 0:00 httpd vlan1
68 ? S 0:00 klogd
71 ? Ss 0:01 nas /tmp/nas.lan.conf /tmp/nas.lan.pid lan
73 ? S 0:00 [dnsmasq]
75 ? S 0:00 [khubd]
83 ? Ss 0:00 lpd
85 ? Ss 0:00 p9100d -f /dev/usb/lp0 0
88 ? Ss 0:00 waveservermain
92 ? Ss 0:00 rcamdmain
96 ? S 0:00 [usb-storage-0]
97 ? S 0:00 [scsi_eh_0]
107 ? Ss 0:00 infosvr br0
108 ? Ss 0:00 watchdog
111 ? Ss 0:00 \_ ntp
118 ? S 0:00 dropbear
241 ? Ss 0:00 \_ dropbear
242 pts/0 Ss 0:00 \_ -sh
245 pts/0 R+ 0:00 \_ ps axf
135 ? S 0:00 [kjournald]
136 ? S 0:00 [kjournald]
162 ? S 0:00 /sbin/syslogd -m 0 -O /opt/var/log/syslog.log -S -l 7
168 ? Ss 0:00 /opt/sbin/cron
177 ? Ss 0:00 /opt/sbin/xinetd -pidfile /var/run/xinetd.pid
187 ? Ss 0:00 /opt/sbin/smbd -D
189 ? Ss 0:00 /opt/sbin/nmbd -D
195 ? S 0:01 upnp -D -L br0 -W vlan1
As firmware I use oleg 1.9.2.7-10
What went wrong?
reinstall transmission.
wengi
reinstall transmission.
wengi
I did that 2 times and nothing ...
Can be an error in the downloaded packages?
shinji257
21-06-2008, 18:38
It is possible that the packages may not be downloading or installing correctly. Try uninstalling the packages and then reinstalling it and see if that works. I do know that I installed it fine recently.
It is possible that the packages may not be downloading or installing correctly. Try uninstalling the packages and then reinstalling it and see if that works. I do know that I installed it fine recently.
did that, still the same ...
It is possible that all this could be caused by the HDD?
I did a e2fsck -fv /dev/discs/disc0/part2, - the IPKG part, and the result is:
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
3132 inodes used (2%)
6 non-contiguous inodes (0.2%)
# of inodes with ind/dind/tind blocks: 58/0/0
14115 blocks used (5%)
0 bad blocks
0 large files
1908 regular files
110 directories
0 character device files
0 block device files
0 fifos
0 links
1105 symbolic links (1105 fast symbolic links)
0 sockets--------
3123 files
Can u post your transmission.conf and version of transmission? Perhaps it is a new ver of transmission and this is why I have this error
Thank you
I have the same problem as bogd_A. I found out that there is no transmission_watchdog in opt/sbin and trasmissiond in opt/bin and also no www subdirectory under opt/share and also busybox does not listen on port 8008. There must be something wrong with transmission package. After I copied all missing files and run 'busybox_httpd -p 8008 -c /opt/etc/httpd.conf -h /opt/share/www' I got transmission to work.
transmissiond inclusion solved with changeset/8556 (http://trac.nslu2-linux.org/optware/changeset/8556). Our package master bzhou downgraded to 1.22 and left out transmissiond.
I recommend ipkg update && ipkg upgrade
zemitras
22-06-2008, 18:27
I'm having the same problem with transmission :(
What files and where do will I put them?
Thanks
I'm having the same problem.. But no new package is available for download.
I did "ipkg update && ipkg upgrade" but it says it has nothing to do.
I am using this one: http://ipkg.nslu2-linux.org/feeds/optware/oleg/cross/stable/transmission_1.22-1_mipsel.ipk
but it's not working.
The firmware is WL500gpv2-1.9.2.7-10.trx
Sometimes you just need to wait a while that autobuild machine (http://logs.nslu2-linux.org/buildlogs/autobuild-builder-last.txt) compiles new package for all platforms!
Packages are now available!
ipkg update
ipkg upgrade
One can also do ipkg force reinstall transmission if fails to upgrade. Bu I doubt it.
the only problem I have with transmission is that somehow no graph data is being written to the file...
so I can't create any graphs.
maybe it's due the fact I have /tmp/harddisk mounted as /mnt
?
I did do the right setup for everything, and changed the values to the right place...
so, oleo, what would you reckon goes wrong?:confused:
(yes I have the lasted transmission)
maybe it's due the fact I have /tmp/harddisk mounted as /mnt
You can test this by creating a symbolic link from /tmp/harddisk to /mnt
wengi
You can test this by creating a symbolic link from /tmp/harddisk to /mnt
wengi
extreamly silly me!
I forgot to do this:
syslog has to be changed:
SYSLOG=/opt/var/log/syslog.log
:o
it seems to work now... but I still don't get how it changed, because it use to work and I always kept my config:confused:
I'm having two problems here :)
First of all, I noticed that when I do ipkg update it updates itself from this url:
http://ipkg.nslu2-linux.org/feeds/unslung/wl500g/Packages
Is that the right URL to use ? I'm using 500gP v2 with latest oleg's fw.
on the upper url I find only this (old transmission version):
Package: transmission
Version: 0.82-3
Depends: openssl, libevent
Conflicts: torrent
Suggests: gnuplot, logrotate, thttpd
Section: net
Architecture: mipsel
Maintainer: NSLU2 Linux <nslu2-linux@yahoogroups.com>
MD5Sum: cb7ecd44bcdc0a8feaae2ec28d9a4859
Size: 405817
Filename: transmission_0.82-3_mipsel.ipk
Source: http://download.m0k.org/transmission/files/transmission-0.82.tar.gz
Description: lightweight BitTorrent client and daemon with WWW interface
I then downloaded the package myself from this url:
http://ipkg.nslu2-linux.org/feeds/optware/oleg/cross/stable/transmission_1.22+r6245-1_mipsel.ipk
And installed it.
That's the point of problem #2 beginning:
Once I do everything described in this tutorial on point #9, I can't get transmission to work:
[admin@router disc0_1]$ transmission_watchdog
/opt/sbin/transmission_watchdog: /opt/sbin/transmission_watchdog: 304: transmissiond: not found
What am I doing wrong ? I only get
Jun 24 20:03:15 transmission_watchdog: Transmission daemon restarted! in my log.
I found this thread (http://forum.openwrt.org/viewtopic.php?id=12773) where a guy had the same problem. He solved it by installing "Uclibc-op", but I rather won't try that, before consulting someone here who is smarter and more expirienced than I am. I don't like the idea of piling loads of various (unneeded?) packages on my router, and slow it down.
What is "Uclibc-op" ? Do I need it ?
please help...
Hi@all,
News for the hanging of transmission webinterface:
Do the following:
Install the shell "bash".
ipkg install bash
Edit transmission.cgi. First line to be replaced with:
#!/opt/bin/bashdone.
technical background: The integrated busybox shell and transmission.cgi do not work 100% ok. The exact problem is not pointed out until now.
29.06.2008
wengi
hi i just get this kind of msg.
http://rapidshare.com/files/127593111/Snap3.bmp
http://rapidshare.com/files/127594398/transmission.bmp
What went wrong ??
after i start manualy transmission_watchdog, its start and stop strange..
[admin@WL500gP /opt]$ ps
PID Uid VmSize Stat Command
1 admin 652 S /sbin/init
2 admin SW [keventd]
3 admin SWN [ksoftirqd_CPU0]
4 admin SW [kswapd]
5 admin SW [bdflush]
6 admin SW [kupdated]
7 admin SW [mtdblockd]
59 admin 328 S telnetd
64 admin 396 S httpd vlan1
71 admin 368 S klogd
72 nobody 464 S dnsmasq
77 admin SW [khubd]
91 admin 320 S infosvr br0
92 admin 484 S watchdog
94 admin SW [usb-storage-0]
95 admin SW [scsi_eh_0]
97 admin 340 S ntp
108 admin 468 S dropbear
122 admin 432 S udhcpc -i vlan1 -p /var/run/udhcpc0.pid -s /tmp/udhcpc
125 admin 580 S -sh
134 admin 552 S upnp -D -L br0 -W vlan1
138 admin SW [kjournald]
139 admin SW [kjournald]
141 admin 404 S stupid-ftpd
143 admin 980 S /usr/sbin/nmbd -D
146 admin 1008 S /usr/sbin/smbd -D
176 admin 396 S /sbin/syslogd -m 0 -O /opt/var/log/messages -S -l 7
183 admin 396 S /sbin/syslogd -m 0 -O /opt/var/log/syslog.log -S -l 7 -s 0
190 admin 408 S /opt/sbin/cron
199 admin 420 S /usr/sbin/busybox_httpd -c /opt/etc/httpd.conf -p 8008 -h /opt/share/www
1178 admin 780 S transmissiond -p 65534 -w 300 -u -1 -d -1 -i /opt/var/run/transmission.pi
1180 admin 780 S transmissiond -p 65534 -w 300 -u -1 -d -1 -i /opt/var/run/transmission.pi
1181 admin 780 S transmissiond -p 65534 -w 300 -u -1 -d -1 -i /opt/var/run/transmission.pi
1184 admin 404 R ps
[admin@WL500gP /opt]$
when i trying start torrent it says /opt/share/www/cgi-bin/transmission.cgi: kill: 9: (1178) - No such process
Hi,
you are running transmission 0.82!!!!
ipkg update
ipkg upgrade
And see the post above with the bash install.
wengi
Hi,
you are running transmission 0.82!!!!
ipkg update
ipkg upgrade
And see the post above with the bash install.
wengi
[admin@WL500gP lists]$ ipkg upgrade
Nothing to be done
Successfully terminated.
[admin@WL500gP lists]$ ipkg update
Downloading http://wl500g.dyndns.org/ipkg/Packages
Updated list of available packages in /opt/lib/ipkg/lists/wl500g
Downloading http://ipkg.nslu2-linux.org/feeds/unslung/wl500g/Packages
Updated list of available packages in /opt/lib/ipkg/lists/unslung
Successfully terminated.
With ver. is correct ? transmission_0.82-3_mipsel.ipk ?
or should I downgrade to transmission_0.6+r961-1_mipsel.ipk??
You did it the wrong way.
First update
Second upgrade
transmission is V1.22 atm.
Is your router setup with my howto?
What does
ipkg list_installedresult in?
wengi
You did it the wrong way.
First update
Second upgrade
transmission is V1.22 atm.
Is your router setup with my howto?
What does
ipkg list_installedresult in?
wengi
[admin@WL500gP root]$ ipkg list_installed
bash - 3.2.17-1 - A bourne style shell
coreutils - 5.2.1-9 -
cron - 4.1-6 - Standard vixie cron, with cron.d addition
ctorrent - 1.3.4-2 - CTorrent is a BitTorrent client written in the C programming language.
diffutils - 2.8.1-4 - contains gnu diff, cmp, sdiff and diff3 to display differences between and among text files
expat - 2.0.1-1 - XML Parser library
findutils - 4.1.20-2 - File finding utilities
fontconfig - 2.3.2-5 - Font configuration library
freetype - 2.1.10-4 - Free truetype library
gconv-modules - 2.2.5-7 - Provides gconv modules missing from the firmware. These are used by glibc's iconv() implementation.
gnuplot - 4.2.0-5 - Command-line driven interactive data and function plotting utility
groff - 1.19.2-2 - front-end for the groff document formatting system
ipkg - 0.99.149-2 - lightweight package management system
less - 394-3 - Less file browser
libbt - 1.05-5 - a C library implementing the core BitTorrent protocol
libcurl - 7.17.0-2 - Curl is a command line tool for transferring files with URL syntax, supporting FTP, FTPS, HTTP, HTTPS, GOPHER, TELNET, DICT, FI
libevent - 1.3d-1 - libevent to implement an event loop
libgd - 2.0.35-1 - An ANSI C library for the dynamic creation of images
libiconv - 1.11-2 - Converts between character encodings.
libjpeg - 6b-2 - collection of jpeg tools
libpng - 1.2.21-1 - Portable Network Graphics Libraries
libstdc++ - 0.2.0-6 -
libuclibc++ - 0.1.12-4 - C++ standard library designed for use in embedded systems
lirc - 0.8.1-2 - Linux Infrared Remote Control (tira)
logrotate - 3.7.1-4 - Rotates, compresses, removes and mails system log files.
man - 1.5p-4 - unix manual page reader
man-pages - 2.33-3 - unix manual pages
mc - 4.1.35-3 -
nano - 2.0.6-1 - A pico like editor
ncurses - 5.6-1 - NCurses libraries
nload - 0.6.0-2 - Nload is a console application which monitors network traffic and bandwidth usage in real time
openssl - 0.9.7m-3 - Openssl provides the ssl implementation in libraries libcrypto and libssl, and is needed by many other applications and librari
pcre - 7.4-1 - Perl-compatible regular expression library
popt - 1.7-2 - A C library for parsing command line parameters.
readline - 5.2-2 - The GNU Readline library provides a set of functions for use by applications that allow users to edit command lines as they are
screen - 4.0.3-2 - A screen manager that supports multiple logins on single terminal
termcap - 1.3.1-2 - Terminal emulation library
transmission - 0.82-3 - lightweight BitTorrent client and daemon with WWW interface
unzip - 5.52-1 - A (de)compression library for the ZIP format
vsftpd - 2.0.5-1 - ftp daemon with an emphasis on speed and security
whois - 4.7.22-1 - Perform whois lookups to identify site owners
zlib - 1.2.3-2 - zlib is a library implementing the 'deflate' compression system.
Successfully terminated.
[admin@WL500gP root]$ ipkg.sh status transmission
Package: transmission
Version: 0.82-3
Depends: openssl, libevent
Suggests: gnuplot, logrotate, thttpd
Conflicts: torrent
Status: install user installed
Architecture: mipsel
i did uninstall torrent and ctorrent
i can't localise V1.22 atm at http://ipkg.nslu2-linux.org/feeds/unslung/wl500g/
I found and install 1.22
[admin@WL500gP root]$ ipkg status transmission
Package: transmission
Version: 1.22-2
Depends: openssl, libcurl
Suggests: gnuplot, logrotate, thttpd, mini-sendmail
Conflicts: torrent
Status: install user installed
Architecture: mipsel
Installed-Time: 1215477169
but now when i starting transmission_watchdog i got this"
[admin@WL500gP root]$ transmission_watchdog
/opt/sbin/transmission_watchdog: /opt/sbin/transmission_watchdog: 304: transmissiond: not found
Hi,
you are in an old repository (http://ipkg.nslu2-linux.org/feeds/unslung/wl500g/)
This means your complete installation is not maintained any more.
I recommend changing the complete system to the new repository.
Have a look at my howto.
I know this is much more work for you but it is wort it.
wengi
Hi
I have the following question: It is possible to download one torrent using my PC, and copy the files on my attached HDD on Wl-500gP and to seed this torrent using transmission.
I have some torrents of 60-70G, downloaded from a torrent tracker, on my PC, because WL-500gP is too weak to proper handdle those torrents, and to maintain my ratio I want to seed them (on the same tracker) from my Wl500gP +HDD which is running 24/24.
What is the max number of torrents I can seed with my WL-500gP + HDD?
Trank you,
Sorry, no idea about that.
wengi
Sorry, no idea about that.
wengi
Found it,
must keep in mind the way the files/folders are structured, so you must keep that structure for torrent files:
one dir:
one sub dir (same name as the parent dir) with the files
the torent file with *.torrent extension
Copy the parent dir in work directory of the hdd, then save the torrent file from the tracker, or other place from which you want to download, as if you would do a normal torrent download.
"update" in transmission web interface, and that's it. it starts the checkimg files process and then seeding.
The only issue is that the torrent stays in work dir and appear as active in transmission :( at least for the momment, I'll wait to see if it is seeding as it should
Hi,
you are in an old repository (http://ipkg.nslu2-linux.org/feeds/unslung/wl500g/)
This means your complete installation is not maintained any more.
I recommend changing the complete system to the new repository.
Have a look at my howto.
I know this is much more work for you but it is wort it.
wengi
I reinstall system, every thing is working fine now, thanks to you wengi:)
@Syl: fine :)
@bogd_A: Did you download the torrents on the pc with transmission or was it another torrent client?
wengi
@Syl: fine :)
@bogd_A: Did you download the torrents on the pc with transmission or was it another torrent client?
wengi
I used uTorrent for downloading the torrents.
Now the torrent is SEEDING, but still no upload from it ... don't know why, there are a lot of leechers on that torrent, and downloading from other uploaders, except me :)
Found it,
must keep in mind the way the files/folders are structured, so you must keep that structure for torrent files:
one dir:
one sub dir (same name as the parent dir) with the files
the torent file with *.torrent extension
Copy the parent dir in work directory of the hdd, then save the torrent file from the tracker, or other place from which you want to download, as if you would do a normal torrent download.
"update" in transmission web interface, and that's it. it starts the checkimg files process and then seeding.
The only issue is that the torrent stays in work dir and appear as active in transmission :( at least for the momment, I'll wait to see if it is seeding as it should
I personally use another method and maybe it can help you.
- download the torrent with uTorrent on the PC
- start the same torrent with transmission to let create the needed directory / files
- stop the torrent in transmission
- copy all the files from the PC to the correct transmission sub folder
- restart the torrent in transmission
transmission will check the torrent integrity an after start the seeding
Happy seeding :D
I personally use another method and maybe it can help you.
- download the torrent with uTorrent on the PC
- start the same torrent with transmission to let create the needed directory / files
- stop the torrent in transmission
- copy all the files from the PC to the correct transmission sub folder
- restart the torrent in transmission
transmission will check the torrent integrity an after start the seeding
Happy seeding :D
I'll try this when I'll get home
I still have an issue accessing my folders shared with samba from my laptop.
I tryed several solutions but none worked.
I can access the shared folders from any PC, PDA, but not from my laptop, the difference is that it is on a windows domain, and I can't change that, beeing my work computer.
Any ideea what I should try?
If I put on my WL-500gP the original firmware, I can access the shared folders on my HDD from that laptop, but when I change to oleg's firmware it doesn't work.
So, my question is: what is the difference between those two firmware regarding the share issue?
jim-easterbrook
09-07-2008, 18:31
I've just discovered that these scripts are called with the disc's id string as a parameter. This makes it possible to avoid having disc checks rerun when another drive (e.g. a USB memory stick) is plugged in. My pre-mount script is now:
#!/bin/sh
logger -t $0 "$*"
if [ $1 = "152d/2338/100" ]; then
# mounting the usb system drive
# turn on swap
swapon -a
# check file systems
for i in `awk '/ext3/{print($1)}' /etc/fstab`; do
if [ -b $i ]; then
grep -q $i /proc/mounts || e2fsck -p $i 2>&1 | logger -t e2fsck
else
logger -t fstab "$i is not attached"
fi
done
# create mount points
for i in `awk '/ext3/{print($2)}' /etc/fstab`; do
mkdir -p $i
done
fiand my post-mount script is:
#!/bin/sh
logger -t $0 "$*"
if [ $1 = "152d/2338/100" ]; then
# mounting the usb system drive
/opt/etc/init.d/rc.unslung start
fiObviously you need to substitute your disc id for the string "152d/2338/100".
Edit: to obtain the disc id, modify your pre-mount or post-mount script to include the line
logger -t $0 "$*", do the flashfs save & commit, reboot and have a look at the syslog.
Thanks for this hint :)
wengi
sory, is it that mean that i lost all data on my hdd??
and the router will check again and again this errors ??
scsi0 : SCSI emulation for USB Mass Storage devices
Vendor: USB Model: Storage Rev: 1.04
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
Partition check:
/dev/scsi/host0/bus0/target0/lun0:SCSI disk error : host 0 channel 0 id 0 lun 0 return code = 70000
I/O error: dev 08:00, sector 0
SCSI disk error : host 0 channel 0 id 0 lun 0 return code = 70000
I/O error: dev 08:00, sector 2
SCSI disk error : host 0 channel 0 id 0 lun 0 return code = 70000
I/O error: dev 08:00, sector 4
SCSI disk error : host 0 channel 0 id 0 lun 0 return code = 70000
I/O error: dev 08:00, sector 6
SCSI disk error : host 0 channel 0 id 0 lun 0 return code = 70000
I/O error: dev 08:00, sector 0
SCSI disk error : host 0 channel 0 id 0 lun 0 return code = 70000
I/O error: dev 08:00, sector 2
SCSI disk error : host 0 channel 0 id 0 lun 0 return code = 70000
I/O error: dev 08:00, sector 4
SCSI disk error : host 0 channel 0 id 0 lun 0 return code = 70000
I/O error: dev 08:00, sector 6
unable to read partition table
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 2
usb.c: USB disconnect on device 01:03.2-2 address 2
Device 08:00 not ready.
I/O error: dev 08:00, sector 2
EXT3-fs: unable to read superblock
MSDOS FS: Using codepage 950
MSDOS FS: IO charset cp950
Device 08:00 not ready.
I/O error: dev 08:00, sector 0
FAT: unable to read boot sector
FAT: freeing iocharset=cp950
Device 08:00 not ready.
I/O error: dev 08:00, sector 0
FAT: unable to read boot sector
Device 08:00 not ready.
I/O error: dev 08:00, sector 0
NTFS: Reading super block failed
Device 08:00 not ready.
I/O error: dev 08:00, sector 0
Device 08:00 not ready.
I/O error: dev 08:00, sector 0
hub.c: connect-debounce failed, port 2 disabled
hub.c: connect-debounce failed, port 2 disabled
hub.c: connect-debounce failed, port 2 disabled
Device 08:00 not ready.
data is (still) not lost.
some informations needed:
- attach the hdd and post results of:
ls -la /dev/discs/disc0/
ls -la /dev/discs/
mount
- which filesystem are you using?
if fat: connect your hdd to your windows pc.
if ext2/3: try e2fsck.
wengi
data is (still) not lost.
some informations needed:
- attach the hdd and post results of:
ls -la /dev/discs/disc0/
ls -la /dev/discs/
mount
- which filesystem are you using?
if fat: connect your hdd to your windows pc.
if ext2/3: try e2fsck.
wengi
After a couple restarts it's stand up again... and every think runs on
[admin@Morph root]$ df
Filesystem 1K-blocks Used Available Use% Mounted on
rootfs 2880 2880 0 100% /
/dev/root 2880 2880 0 100% /
/dev/discs/disc0/part2
16199952 203248 15173776 2% /opt
/dev/discs/disc0/part3
95121256 218356 90070952 1% /tmp/harddisk
[admin@Morph root]$ umount -l /opt
[admin@Morph root]$ df
Filesystem 1k-blocks Used Available Use% Mounted on
/dev/root 2880 2880 0 100% /
/dev/discs/disc0/part3 95121256 218356 90070952 0% /tmp/harddisk
[admin@Morph root]$ umount -l /tmp/harddisk/
[admin@Morph root]$ df
Filesystem 1k-blocks Used Available Use% Mounted on
/dev/root 2880 2880 0 100% /
[admin@Morph root]$ e2fsck -py /dev/discs/disc0/part2
e2fsck: Only one the options -p/-a, -n or -y may be specified.
[admin@Morph root]$ e2fsck -p /dev/discs/disc0/part2
/dev/discs/disc0/part2: recovering journal
e2fsck: while trying to re-open /dev/discs/disc0/part2
[admin@Morph root]$ e2fsck -p /dev/discs/disc0/part3
/dev/discs/disc0/part3: recovering journal
e2fsck: while trying to re-open /dev/discs/disc0/part3
[admin@Morph root]$ ls -la /dev/discs/disc0/
drwxr-xr-x 1 admin root 0 Jan 1 1970 .
drwxr-xr-x 1 admin root 0 Jan 1 1970 ..
brw------- 1 admin root 8, 0 Jan 1 1970 disc
brw------- 1 admin root 8, 1 Jan 1 1970 part1
brw------- 1 admin root 8, 2 Jan 1 1970 part2
brw------- 1 admin root 8, 3 Jan 1 1970 part3
[admin@Morph root]$ ls -la /dev/discs/
drwxr-xr-x 1 admin root 0 Jan 1 1970 .
drwxr-xr-x 1 admin root 0 Jan 1 1970 ..
lr-xr-xr-x 1 admin root 31 Jan 1 1970 disc0 -> ../scsi/host0/bus0/target0/lun0
[admin@Morph root]$
[admin@Morph root]$ ps
PID Uid VmSize Stat Command
1 admin 652 S /sbin/init
2 admin SW [keventd]
3 admin RWN [ksoftirqd_CPU0]
4 admin SW [kswapd]
5 admin SW [bdflush]
6 admin SW [kupdated]
7 admin SW [mtdblockd]
59 admin 308 S telnetd
64 admin 448 S httpd vlan1
71 admin 368 S klogd
72 nobody 488 S dnsmasq
77 admin SW [khubd]
91 admin 320 S infosvr br0
92 admin 492 S watchdog
95 admin 340 S ntp
99 admin SW [usb-storage-0]
103 admin SW [scsi_eh_0]
110 admin 480 S dropbear
153 admin 432 S udhcpc -i vlan1 -p /var/run/udhcpc0.pid -s /tmp/udhcp
164 admin SW [kjournald]
165 admin SW [kjournald]
167 admin 412 S stupid-ftpd
169 admin 1004 S /usr/sbin/nmbd -D
171 admin 1012 S /usr/sbin/smbd -D
198 admin 396 S /sbin/syslogd -m 0 -O /opt/var/log/syslog.log -S -l 7
211 admin 420 S /usr/sbin/busybox_httpd -c /opt/etc/httpd.conf -p 800
250 admin 1564 S N transmissiond -p 65534 --nat-traversal -w 300 -u -1 -
253 admin 1564 S N transmissiond -p 65534 --nat-traversal -w 300 -u -1 -
254 admin 1564 S N transmissiond -p 65534 --nat-traversal -w 300 -u -1 -
308 admin 756 S dropbear
309 admin 580 S -sh
421 admin 508 S upnp -D -L br0 -W vlan1
485 admin 404 R ps
[admin@Morph root]$ fdisk -l
Disk /dev/scsi/host0/bus0/target0/lun0/disc: 120.0 GB, 120034123776 bytes
255 heads, 63 sectors/track, 14593 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/scsi/host0/bus0/target0/lun0/part1 1 513 4120641 82 Linux swap
/dev/scsi/host0/bus0/target0/lun0/part2 514 2562 16458592+ 83 Linux
/dev/scsi/host0/bus0/target0/lun0/part3 2563 14593 96639007+ 83 Linux
but if i do flashfs save && flashfs commit && flashfs enable && reboot
its gone again and sometimes starts but sometimes doesnt.
kernel :wrong partition table.
save your data!
it seems you hdd begins to crash.
wengi
PS: you can attach the hdd to a winPC and use the manufacturers utils to test it. (you need to know the brand of the hdd)
I personally use another method and maybe it can help you.
- download the torrent with uTorrent on the PC
- start the same torrent with transmission to let create the needed directory / files
- stop the torrent in transmission
- copy all the files from the PC to the correct transmission sub folder
- restart the torrent in transmission
transmission will check the torrent integrity an after start the seeding
Happy seeding :D
HI,
Thanks for the tip, it works your way too :)
HI,
3315
Looking at my transmission graph it looks like it has moments when the downloading/uploading speed drops to 0 and then it resume downloading/uploading.
It is normal or it is something else?
What is the max number of torrents that I can seed at one time?
Thank you
the stopping of the download is quite normal for you lol
max up: 800
max down: 1400:p
crazy man...
what happens is this:
too many ppl with incomplete files waiting for seeders, when you downloaded everything available at that time, your downloading stops...
as soon as someone starts to seed the files your missing and your download begins again;)
optic fiber internet?
the stopping of the download is quite normal for you lol
max up: 800
max down: 1400:p
crazy man...
what happens is this:
too many ppl with incomplete files waiting for seeders, when you downloaded everything available at that time, your downloading stops...
as soon as someone starts to seed the files your missing and your download begins again;)
optic fiber internet?
Thank you for you answer.
It's a ... regular cable connection
Hi,
In think there are some issues with the new trans version (1.22-3)
- after pushing a torrent to start it takes a long time to start, longer than with the previous version
- when a torrent changes his state from active to seeding, the other downloading/uploading torrents stops, the downloading/uploading resumes after pressing "Watchdog"
- the overal speed is lower than the one I had with the previous version (1.22-2).
- I have one torrent that it was checked, and it stays at 100% for some hours now, and if I start a new torrent it automatically checking it, and it wont start unless the first one finishes.
Is there a way to install the previous verssion?
I'm not using Transmission, but I'd like to set up log rotation. Can someone tell me which part of this guide in chapters 9/9b is relevant to me if I only want to set up log rotation? I'd like to make it save logs into a subdirectory on /tmp/harddisk (while still keep the current method of sending logs into the PC in my LAN; my current ps axf regarding syslogd says: syslogd -m 0 -O /tmp/syslog.log -S -l 7 -R 192.168.XX.XX -L )
Simply start with 9b.
insert cron entry and edit logrotate.conf.
Thats it.
wengi
Do I have to edit the line
OPTIONS="-m 0 -O $LOG_NEW/$LOGFILE -S -l 7 -s 0"
to include those extra options I have now by default?
If you are talking about syslog startup file: yes.
wengi
Is there still a package lirc or igorplususb?
I don't find them!
http://ipkg.nslu2-linux.org/feeds/optware/oleg/cross/stable/Packages
not from optware.
wengi
stefantriep
27-07-2008, 19:29
getting error before formatting disk
[stefan@AsusServer root]$ fdisk /dev/discs/disc0/disc
Unable to open /dev/discs/disc0/disc
any idea?
Just following your how to from point 1
[stefan@AsusServer root]$ ps
PID Uid VmSize Stat Command
1 stefan 660 S /sbin/init
2 stefan SW [keventd]
3 stefan SWN [ksoftirqd_CPU0]
4 stefan SW [kswapd]
5 stefan SW [bdflush]
6 stefan SW [kupdated]
7 stefan SW [mtdblockd]
43 stefan 308 S telnetd
48 stefan 380 S httpd eth1
54 stefan 368 S klogd
55 nobody 464 S dnsmasq
56 stefan 400 S syslogd -m 0 -O /tmp/syslog.log -S -l 7
61 stefan SW [khubd]
73 stefan 448 S watchdog
75 stefan 344 S ntp
87 stefan 480 S dropbear
95 stefan 432 S udhcpc -i eth1 -p /var/run/udhcpc0.pid -s /tmp/udhcpc
100 stefan 748 S dropbear
101 stefan 556 S -sh
118 stefan 396 R ps
bigphantom
27-07-2008, 21:29
did you unmount the file ?
umount /tmp/mnt/discX_X
just post the output of the following command
df
getting error before formatting disk
[stefan@AsusServer root]$ fdisk /dev/discs/disc0/disc
Unable to open /dev/discs/disc0/disc
any idea?
Just following your how to from point 1
[stefan@AsusServer root]$ ps
PID Uid VmSize Stat Command
1 stefan 660 S /sbin/init
2 stefan SW [keventd]
3 stefan SWN [ksoftirqd_CPU0]
4 stefan SW [kswapd]
5 stefan SW [bdflush]
6 stefan SW [kupdated]
7 stefan SW [mtdblockd]
43 stefan 308 S telnetd
48 stefan 380 S httpd eth1
54 stefan 368 S klogd
55 nobody 464 S dnsmasq
56 stefan 400 S syslogd -m 0 -O /tmp/syslog.log -S -l 7
61 stefan SW [khubd]
73 stefan 448 S watchdog
75 stefan 344 S ntp
87 stefan 480 S dropbear
95 stefan 432 S udhcpc -i eth1 -p /var/run/udhcpc0.pid -s /tmp/udhcpc
100 stefan 748 S dropbear
101 stefan 556 S -sh
118 stefan 396 R ps
stefantriep
27-07-2008, 22:03
df shows 1 mount
/dev/root /
Hi,
first we need more info:
Model?
HDD?
ISE/USB?
Firmware?
is the disc present?
Any errors in syslog?
Post result of
ls -la /dev/discs/
df
mount
wengi
Arbadelli
29-07-2008, 21:24
Thanks for this Tut again!!
It worked now with my 1TB HDD
but is there a possibillity you can make a tool which give me information about the Free GB's and used GB's on the HDD?
So everybody knows how much the can use anyway.
Thanks anyway for the answer
but is there a possibillity you can make a tool which give me information about the Free GB's and used GB's on the HDD?
SSH/telnet: df -h
Samba: Map share as drive and explorer will show the info
ftp: No idea
wengi
stefantriep
30-07-2008, 14:08
Hi,
first we need more info:
Modell: WL 500g
HDD: Hitachi 100 GB
ISE/USB: USB 2.0 HDD
Firmware: Oleg 1.9.2.7-7g
is the disc present? Disk connected before router startup, it is a empty disk
Any errors in syslog?
[stefan@AsusServer /tmp]$ vi syslog.log
Jan 1 01:00:02 syslogd started: BusyBox v1.1.3
Jan 1 01:00:02 kernel: zone(1): 0 pages.
Jan 1 01:00:02 kernel: zone(2): 0 pages.
Jan 1 01:00:02 kernel: Kernel command line: root=/dev/mtdblock2 noinitrd init=/
Jan 1 01:00:02 kernel: CPU: BCM4710 rev 0 at 125 MHz
Jan 1 01:00:02 kernel: !unable to setup serial console!
Jan 1 01:00:02 kernel: Calibrating delay loop... 82.94 BogoMIPS
Jan 1 01:00:02 kernel: Memory: 13840k/16384k available (1799k kernel code, 2544
Jan 1 01:00:02 kernel: Dentry cache hash table entries: 2048 (order: 2, 16384 b
Jan 1 01:00:02 kernel: Inode cache hash table entries: 1024 (order: 1, 8192 byt
Jan 1 01:00:02 kernel: Mount-cache hash table entries: 512 (order: 0, 4096 byte
Jan 1 01:00:02 kernel: Buffer-cache hash table entries: 1024 (order: 0, 4096 by
Jan 1 01:00:02 kernel: Page-cache hash table entries: 4096 (order: 2, 16384 byt
Jan 1 01:00:02 kernel: Checking for 'wait' instruction... unavailable.
Jan 1 01:00:02 kernel: POSIX conformance testing by UNIFIX
Jan 1 01:00:02 kernel: PCI: Fixing up bus 0
Jan 1 01:00:02 kernel: PCI: Fixing up bridge
Jan 1 01:00:02 kernel: PCI: Fixing up bus 1
Jan 1 01:00:02 kernel: Linux NET4.0 for Linux 2.4
Jan 1 01:00:02 kernel: Based upon Swansea University Computer Society NET3.039
Jan 1 01:00:02 kernel: Initializing RT netlink socket
Jan 1 01:00:02 kernel: Starting kswapd
Jan 1 01:00:02 kernel: Journalled Block Device driver loaded
Jan 1 01:00:02 syslogd started: BusyBox v1.1.3
Jan 1 01:00:02 kernel: zone(1): 0 pages.
Jan 1 01:00:02 kernel: zone(2): 0 pages.
Jan 1 01:00:02 kernel: Kernel command line: root=/dev/mtdblock2 noinitrd init=/linuxrc console=ttyS0,115200
Jan 1 01:00:02 kernel: CPU: BCM4710 rev 0 at 125 MHz
Jan 1 01:00:02 kernel: !unable to setup serial console!
Jan 1 01:00:02 kernel: Calibrating delay loop... 82.94 BogoMIPS
Jan 1 01:00:02 kernel: Memory: 13840k/16384k available (1799k kernel code, 2544k reserved, 248k data, 68k init, 0k highmem)
Jan 1 01:00:02 kernel: Dentry cache hash table entries: 2048 (order: 2, 16384 bytes)
Jan 1 01:00:02 kernel: Inode cache hash table entries: 1024 (order: 1, 8192 bytes)
Jan 1 01:00:02 kernel: Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Jan 1 01:00:02 kernel: Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Jan 1 01:00:02 kernel: Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
Jan 1 01:00:02 kernel: Checking for 'wait' instruction... unavailable.
Jan 1 01:00:02 kernel: POSIX conformance testing by UNIFIX
Jan 1 01:00:02 kernel: PCI: Fixing up bus 0
Jan 1 01:00:02 kernel: PCI: Fixing up bridge
Jan 1 01:00:02 kernel: PCI: Fixing up bus 1
Jan 1 01:00:02 kernel: Linux NET4.0 for Linux 2.4
Jan 1 01:00:02 kernel: Based upon Swansea University Computer Society NET3.039
Jan 1 01:00:02 kernel: Initializing RT netlink socket
Jan 1 01:00:02 kernel: Starting kswapd
Jan 1 01:00:02 kernel: Journalled Block Device driver loaded
Jan 1 01:00:02 kernel: devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
Jan 1 01:00:02 kernel: devfs: boot_options: 0x1
Jan 1 01:00:02 kernel: NTFS driver v1.1.22 [Flags: R/O]
Jan 1 01:00:02 kernel: pty: 256 Unix98 ptys configured
Jan 1 01:00:02 kernel: Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
Jan 1 01:00:02 kernel: HDLC line discipline: version $Revision$, maxframe=4096
Jan 1 01:00:02 kernel: N_HDLC line discipline registered.
Jan 1 01:00:02 kernel: loop: loaded (max 8 devices)
Jan 1 01:00:02 kernel: PPP generic driver version 2.4.2
Jan 1 01:00:02 kernel: PPP Deflate Compression module registered
Jan 1 01:00:02 kernel: PPP BSD Compression module registered
Jan 1 01:00:02 kernel: MPPE/MPPC encryption/compression module registered
Jan 1 01:00:02 kernel: Amd/Fujitsu Extended Query Table v1.0 at 0x0040
Jan 1 01:00:02 kernel: Flash Id: Vendor: 0x0020 Device: 0x00ca
Jan 1 01:00:02 kernel: Physically mapped flash: JEDEC Device ID is 0xCA. Assuming broken CFI table.
Jan 1 01:00:02 kernel: Physically mapped flash: Swapping erase regions for broken CFI table.
Jan 1 01:00:02 kernel: number of CFI chips: 1
Jan 1 01:00:02 kernel: Flash device: 0x400000 at 0x1fc00000
Jan 1 01:00:02 kernel: Physically mapped flash: squashfs filesystem found at block 941
Jan 1 01:00:02 kernel: Creating 5 MTD partitions on "Physically mapped flash":
Jan 1 01:00:02 kernel: 0x00000000-0x00040000 : "pmon"
Jan 1 01:00:02 kernel: 0x00040000-0x003f0000 : "linux"
Post result of
[stefan@AsusServer root]$ df
Filesystem 1k-blocks Used Available Use% Mounted on
/dev/root 2880 2880 0 100% /
[stefan@AsusServer root]$ ls -la /dev/discs/
ls: /dev/discs/: No such file or directory
[stefan@AsusServer root]$ mount
/dev/root on / type squashfs (ro)
none on /dev type devfs (rw)
proc on /proc type proc (rw)
ramfs on /tmp type ramfs (rw)
usbfs on /proc/bus/usb type usbfs (rw)
wengi
I hope you can find something
Hi,
please post result of "lsmod".
Is the above all of the syslog? There should be more....
wengi
stefantriep
30-07-2008, 16:15
[stefan@AsusServer root]$ lsmod
Module Size Used by
printer 12676 0 (unused)
lp 8668 0
parport_splink 2956 1
parport 25696 1 [lp parport_splink]
usb-ohci 21940 0 (unused)
usbcore 77264 1 [printer usb-ohci]
ip_nat_ftp 3944 0 (unused)
ip_conntrack_ftp 5248 1
ipt_NETMAP 992 0 (unused)
ip_nat_starcraft 2224 0 (unused)
wl 423856 0 (unused)
et 34912 0 (unused)
stefantriep
30-07-2008, 16:54
Hi,
please post result of "lsmod".
Is the above all of the syslog? There should be more....
wengi
Yes that is the syslog. The AsusServer is most of the time powered off and this is the syslog after 1 minute startup
stefantriep
30-07-2008, 17:53
Opening fdisk
[stefan@Server9 root]$ fdisk
BusyBox v1.1.3 (2007.01.01-14:37+0000) multi-call binary
Usage: fdisk [-luv] [-C CYLINDERS] [-H HEADS] [-S SECTORS] [-b SSZ] DISK
You are missing a module!
[admin@blechbuechse root]$ lsmod
Module Size Used by
nfsd 93016 1
lockd 64236 1 [nfsd]
sunrpc 83480 1 [nfsd lockd]
usb-storage 62184 0 (unused)
sd_mod 13292 0 (unused)
scsi_mod 70216 1 [usb-storage sd_mod]
printer 12676 0 (unused)
usb-ohci 21940 0 (unused)
usbcore 77264 1 [usb-storage usb-ohci]
ipt_NETMAP 992 0 (unused)
ip_nat_starcraft 2224 0 (unused)
wl 423856 0 (unused)
et 34912 0 (unused)
ide-disk 13524 3
ide-probe-mod 11468 0
ide-mod 109608 3 [ide-disk ide-probe-mod]
This one is normaly loaded by default.
Make sure you do not unload it in any startup script!
Otherwise try
insmod /lib/modules/2.4.20/usb-storage.o
wengi
stefantriep
01-08-2008, 00:29
When I disable FTP usb-storage will dissapear after a restart
I will try an older firmware tomorrow!
Now using 1.9.2.7-7g
Why not using the newest firmware?
wengi
stefantriep
01-08-2008, 10:15
I am now using 1.9.2.7-7f with FTP enabled and it works again.
I will upgrade to 1.9.2.7-7g tonight also with FTP enabled. But you prescribe to dissable FTP, strange that it doesn't work. I'm happy with this option. My mission is to have a NZB Newsgroup download server and Torrent download server with my Asus router
1.9.2.7-7g is the newest one for WL 500g routers, isn't it?
Nope :eek: 1.9.2.7-9
http://oleg.wl500g.info/
wengi
stefantriep
01-08-2008, 12:04
Nope :eek: 1.9.2.7-9
http://oleg.wl500g.info/
wengi
IMPORTANT: This firmware no longer supports original WL-500g/b/bv2/WL-300g/WL-HDD units: hardware vendor no longer support BCM4702 CPU. Use 1.9.2.7-9 instead.
IMPORTANT: This firmware no longer supports original WL-500g/b/bv2/WL-300g/WL-HDD units: hardware vendor no longer support BCM4702 CPU. Use 1.9.2.7-9 instead.
1.9.2.7-9!!! and NOT 1.9.2.7-7g
stefantriep
01-08-2008, 14:31
aha ok, i see, i have to learn to read better :P
I thought this how to was the same as in march, but it's up-to-date to the latest firmware.
Very nice Wengi, it's working now! Thanx for the support
First of all: linux-knowledge is probably below average.. i learnt most of it using this tutorial and the freesco router I used to have.. so if my questions are rather stupid.. excuse me :rolleyes:
Because my HD was going crazy at times I decided to install the swap and opt on an USB-stick.. now this one will eventually wear out.. and that is my concern: would there be any way for me to backup the /opt so I could just insert a new USB-stick in the future such that all settings remain the same?
(also: a 2nd question. I did this yesterday.. and since I used this tutorial I now had 3 partitions on my harddisk
1: [previous] swap
2: [previous] opt
3: harddisk
When trying to mount the harddisk to the actual /tmp/harddisk in Fstab I failed. The device just mounted everything to disc0_1 etc. when I ran mount -a it was fine - that is the harddisk (discx_3) was actually mounted on /tmp/harddisk.. however this solution did not sound good to me so I just deleted partitions 1 and 2.. which did the trick.
Is there any way to actually mount that partition using fstab?)
Hi,
backing up /opt is simply copying the files with 'cp'. Maybe you should stop the services running from /opt before. It is not a boot partition, so no need to image it.
swap does not need to be backed up.
Mounting is working fine for me as it is described in the howto.
it mounts to disk0_3 and creates a symbolic link at /tmp/harddisk.
so no prob at all.
wengi
Arbadelli
11-08-2008, 18:22
it's still working good!!
Valentin
23-08-2008, 06:02
Hi!
First Thanx for the great tutorial! I've folowed all your instructions and everything works just fine. But now I have a little problem.
I've installed transmission with ipkg. After reboot I tryed to start transmission with the command transmission_watchdog but no command like that in my distro. I'm using WL500gp V1 oleg 1.9.2.7-9.
I've had problems with 1.9.2.7-10, it won't connect my ISP sometimes for some reason, but this version works just fine for me.
Please help!
Arbadelli
23-08-2008, 21:40
Hello Wengi,
what can i do?
All worked perfect, my Transmission was working great!!
Till, for 3 hours ago, i saw my Transmission was not downloading / uploading any torrent.
i was thinking it was possible, but after 15 minutes, still no change!
Before that he was working great for about 1 month, i guess..
Now, i thought, i will reboot the router, so he will start all the stuff again, and it would be working again.
Problem..
When i go to my http://192.168.1.1:8008/cgi-bin/transmission.cgi
He couldn't find the page
Ok, i started putty, and logged in, ( yeah, i am in the root of the router )
i think the problem is, he cannot mount the HDD.
before that i could find my hdd with ( windows network places )
so, i think it is not the HDD
but before i enter this :)
i thought i will check before i press Enter
i
The HDD was turned on. ( i saw the blue led was burning )
I turned off the router, after that i turned off the HDD,
I turned on the HDD. But now, I hear he is going on, but after 20 seconds, i give a flash (<- the led is going on, and off.) And i hear the noise is going away, so he turned off.
Maybe is my HDD the problem, i don't hope so, i have much stuff on it, i would keep...
Maybe you can tell me what's the problem
thanks for the help
__________________________________________________ _______________
================================================== ========
Solve some problems, but...
i solved the problem with the HDD,
the power problem was solved.
i tested it without connecting the usb cable.
and if i do that, the power light is flashing blue, and the hdd goes off.
now i can connect cgi-bin/transmission.cgi
i will see the screen, but he is not uploading or downloading,
when i push a torrent, i will see the next text:
/opt/share/www/cgi-bin/transmission.cgi: kill: 9: (3373) - No such process
i will look if i can find a answer to solve this problem.
if you can tell it my, i will thank you for that.
__________________________________________________ _______________
================================================== ========
Maybe i am a stupid usesr ;P
but offcourse, i have to push pause first, after that push watchdog, and now he is checking files.
Still my question is there, why he was stopping uploading and downloading, but i think now he is working agian.
( it is possible i am stupid, but now i solved it myself, not because i have a great knowledge, but by trying something.)
Hi all,
@Valentin
[admin@blechbuechse root]$ find /opt/ | grep -i transmission
/opt/lib/ipkg/info/transmission.conffiles
/opt/lib/ipkg/info/transmission.control
/opt/lib/ipkg/info/transmission.postinst
/opt/lib/ipkg/info/transmission.list
/opt/etc/transmission.conf
/opt/share/man/man1/transmissioncli.1
/opt/share/man/man1/transmission-daemon.1
/opt/share/man/man1/transmission-remote.1
/opt/share/doc/transmission
/opt/share/doc/transmission/NEWS
/opt/share/doc/transmission/README.daemon
/opt/share/www/cgi-bin/transmission2.cgi
/opt/share/www/cgi-bin/transmission.cgi
/opt/share/www/cgi-bin/transmissionorig.cgi
/opt/bin/transmission-daemon
/opt/bin/transmission-remote
/opt/bin/transmissiond
/opt/bin/transmissioncli
/opt/bin/transmissiond-dbg
/opt/sbin/transmission_watchdogYou should have a look at /opt/sbin.
@Arbadelli
so all is fine now?
wengi
I have a very simple question. Is wireless client working properly on the latest fw??
I tried a lot of configs and I didn't manage to get it working.
access point mode.
same ssid and same encryption (wpa2 +aes)
extended mode (ethernet bridge and station)
Does anyone have the correct configuration for this to work?
Valentin
25-08-2008, 18:44
[QUOTE=wengi;109088]Hi all,
@Valentin
[admin@blechbuechse root]$ find /opt/ | grep -i transmission
/opt/lib/ipkg/info/transmission.conffiles
/opt/lib/ipkg/info/transmission.control
/opt/lib/ipkg/info/transmission.postinst
/opt/lib/ipkg/info/transmission.list
/opt/etc/transmission.conf
/opt/share/man/man1/transmissioncli.1
/opt/share/man/man1/transmission-daemon.1
/opt/share/man/man1/transmission-remote.1
/opt/share/doc/transmission
/opt/share/doc/transmission/NEWS
/opt/share/doc/transmission/README.daemon
/opt/share/www/cgi-bin/transmission2.cgi
/opt/share/www/cgi-bin/transmission.cgi
/opt/share/www/cgi-bin/transmissionorig.cgi
/opt/bin/transmission-daemon
/opt/bin/transmission-remote
/opt/bin/transmissiond
/opt/bin/transmissioncli
/opt/bin/transmissiond-dbg
/opt/sbin/transmission_watchdogYou should have a look at /opt/sbin.
Hi Wengi!
I typed in the command you wrote, but my output looks a little different. Did I do something wrong?
/opt/etc/transmission.conf
/opt/lib/ipkg/info/transmission.conffiles
/opt/lib/ipkg/info/transmission.control
/opt/lib/ipkg/info/transmission.list
/opt/bin/transmission-daemon
/opt/bin/transmission-remote
/opt/bin/transmissioncli
/opt/share/man/man1/transmission-daemon.1
/opt/share/man/man1/transmission-remote.1
/opt/share/man/man1/transmissioncli.1
/opt/share/doc/transmission
/opt/share/doc/transmission/COPYING
/opt/share/doc/transmission/ChangeLog
/opt/share/doc/transmission/NEWS
/opt/share/doc/transmission/README
/opt/share/transmission
/opt/share/transmission/web
/opt/share/transmission/web/LICENSE
/opt/share/transmission/web/images
/opt/share/transmission/web/images/buttons
/opt/share/transmission/web/images/buttons/info_activity.png
/opt/share/transmission/web/images/buttons/info_general.png
/opt/share/transmission/web/images/buttons/tab_backgrounds.png
/opt/share/transmission/web/images/buttons/toolbar_buttons.png
/opt/share/transmission/web/images/buttons/torrent_buttons.png
/opt/share/transmission/web/images/favicon.ico
/opt/share/transmission/web/images/graphics
/opt/share/transmission/web/images/graphics/browser_firefox.gif
/opt/share/transmission/web/images/graphics/browser_opera.gif
/opt/share/transmission/web/images/graphics/browser_safari.gif
/opt/share/transmission/web/images/graphics/chrome.png
/opt/share/transmission/web/images/graphics/filter_bar.png
/opt/share/transmission/web/images/graphics/iphone_chrome.png
/opt/share/transmission/web/images/graphics/logo.png
/opt/share/transmission/web/images/graphics/transfer_arrows.png
/opt/share/transmission/web/images/progress
/opt/share/transmission/web/images/progress/progress.png
/opt/share/transmission/web/images/webclip-icon.png
/opt/share/transmission/web/index.html
/opt/share/transmission/web/javascript
/opt/share/transmission/web/javascript/common.js
/opt/share/transmission/web/javascript/dialog.js
/opt/share/transmission/web/javascript/jquery
/opt/share/transmission/web/javascript/jquery/jquery-dimensions.min.js
/opt/share/transmission/web/javascript/jquery/jquery.contextmenu.min.js
/opt/share/transmission/web/javascript/jquery/jquery.form.min.js
/opt/share/transmission/web/javascript/jquery/jquery.min.js
/opt/share/transmission/web/javascript/jquery/jquery.transmenu.min.js
/opt/share/transmission/web/javascript/jquery/json.min.js
/opt/share/transmission/web/javascript/menu.js
/opt/share/transmission/web/javascript/torrent.js
/opt/share/transmission/web/javascript/transmission.js
/opt/share/transmission/web/javascript/transmission.remote.js
/opt/share/transmission/web/stylesheets
/opt/share/transmission/web/stylesheets/common.css
/opt/share/transmission/web/stylesheets/iphone.css
THX for your help in advance
Valentin
Arbadelli
25-08-2008, 22:47
@Arbadelli
so all is fine now?
wengi
Hey Wengi,
not it isn't well now..
i have a strange thing. maybe you can give me the answer!?? ..: i hope :..
the whole evening my torrents are standing
Checking files... 12.68 % Start: 24 Aug 14:17 End: 25 Aug 22:42 uploaded:
also when i push a Queued torrent he will tell me:
Checking files... 0.00 % Start: 25 Aug 23:07 uploaded: 0.0 MB
but, after 1 hour, he will give me the same information.
i cannot push it, because the torrent has to be suspended. So the only thing is to remove the torrent. ( but i won't remove it )
What can i do?
Hope you can give me a answer.
@all.
Have a look at http://wl500g.info/showthread.php?t=15562
Transmission was splitted into two packages.
i am still using an old version and did not upgrade.
Maybe i will do some research to solve your probs. But this will take some days.
The main question: Will we use transmission or transmissiond in future?
The transmission we know until now is called transmissiond in future. (Version 1.22 atm)
The new transmission (Version 1.33 atm) comes with clutch as webinterface
wengi
Valentin
26-08-2008, 13:48
@all.
Have a look at http://wl500g.info/showthread.php?t=15562
Transmission was splitted into two packages.
i am still using an old version and did not upgrade.
Maybe i will do some research to solve your probs. But this will take some days.
The main question: Will we use transmission or transmissiond in future?
The transmission we know until now is called transmissiond in future. (Version 1.22 atm)
The new transmission (Version 1.33 atm) comes with clutch as webinterface
wengi
That makes sense! Thanx for your fast response, I'll try the other version.
Hope It'll work. Allthough I might check the scripts if this version has different commands.
Valentin
28-08-2008, 13:16
Hello Wengi!
The latest version of Transmission works for me really good, so I think I'll start using it. It is really rich in features, really fast, no big cou resource needed, so I've got only good experience with it! ;);
Thx for your answers again.
Valentin
That makes sense! Thanx for your fast response, I'll try the other version.
Hope It'll work. Allthough I might check the scripts if this version has different commands.
kelvinowngyw
29-08-2008, 05:04
Is there any client that can select files in torrent?:confused:
Is there any client that can select files in torrent?:confused:
Hi,
i do not understand the question :confused:
wengi
Hi,
i do not understand the question :confused:
wengi
I think what he ment is:
when you are using a client like bitcomet, you can select wich files to download from the torrent.
torrents can describe multiple files (as you probably know), so sometimes you only want to download a small file, and not all the files, wich would take hours:p
kelvinowngyw
30-08-2008, 09:41
I think what he ment is:
when you are using a client like bitcomet, you can select wich files to download from the torrent.
torrents can describe multiple files (as you probably know), so sometimes you only want to download a small file, and not all the files, wich would take hours:p
that what is want to ask. thanks
sorry for my bad
after an upgrade/update from 1.22 to 1.33 transmission went bad:
"Connection Interrupted
The connection to the server was reset while the page was loading.
The network link was interrupted while negotiating a connection. Please try again."
how I fix this thing?
terabyte
01-09-2008, 05:34
Hi wengi, when can we expect an update to your how-to using the new transmission package? thanks!
dear wengi,
would you be so kind add your tutorial , installing mediatomb media server ,I've been trying to install from another thread http://www.wl500g.info/showthread.php?t=13963 , but have no luck allways get error " terminate called after throwing an instance of 'zmm::Exception' ".:confused:
thx
sas
@zexe
You should have read at least the last few posts:
http://wl500g.info/showpost.php?p=109189&postcount=379
@terabyte
I will wait until oleo finished the changes.
Until then i will use the transmissiond package in the howtos.
@hdmovie
Sorry, but i will only add things to the howto if i am using them myself.
This is the only way to give a good support.
No media server on my wl-hdd means no media server in the howto.
You will have to use other howtos in this board.
wengi
mataanjin
10-09-2008, 13:23
if i want to turnoff the hdd, is there any step i must do? and when i turn it on again?
how to download from a direct link?
tq
if i want to turnoff the hdd, is there any step i must do? and when i turn it on again?
Do a forum search for hdd spindown.
how to download from a direct link?
with wget. 'wget http://www......'
wengi
if i want to turnoff the hdd, is there any step i must do? and when i turn it on again?
how to download from a direct link?
tq
Hi, I believe this is option is standard available. But, if you use the hdd for swap and/or have cron installed (which accesses the hdd every minute) the hdd doesn't have any 'inactive' time so it won't spin down. Also, from what I read from the forum is that the WiFi WLAN function causes hdd-access so it won't spin down when WLAN is enabled.
anyway, the following link should provide information: http://wlhdd.co.uk/wiki/HDD_Standby
code: (for spindown after 10 minutes)
hdparm -S 120 /dev/discs/disc0/disc
(info taken from thread: http://www.wl500g.info/showthread.php?t=12916&highlight=spin)
HTH
r3ap3rpl
16-09-2008, 01:06
Hi,
I already installed Oleg, before I was using OpenWRT on my Asus wl500gp.
All works fine for me,but I have problem with permissions to /opt dir.
[root@WL-001BFC918B60 root]$ mkdir -p /opt/tmp
mkdir: Cannot create directory `/opt/tmp': Read-only file system
the same or similar when I trying:
mkdir -p /opt/tmp
ipkg.sh install ipkg-opt
mkdir /opt/tmp
I searched the web with google and I can't find any solution when I'm not using an external usb-hdd. I want to install ipkg, mc, nano, iptraf and maybe 4 apps more - I don't need usb-hdd.... I think ;)
[root@WL-001BFC918B60 root]$ mount
/dev/root on / type squashfs (ro)
none on /dev type devfs (rw)
proc on /proc type proc (rw)
ramfs on /tmp type ramfs (rw)
usbfs on /proc/bus/usb type usbfs (rw)
[root@WL-001BFC918B60 root]$ df -h
Filesystem Size Used Available Use% Mounted on
/dev/root 2.9M 2.9M 0 100% /
thanks for your time :)
ps
sorry for my gramma (if there are some mistakes;) ), english isn't my native language, but I'm trying :D
when I'm looking for same solution :D
Hi,
no need to browse the web.
Simply rtfm:
Remark: If you get a "mkdir: Cannot create directory `/opt/etc': Read-only file system" your HDD (here the IPKG pertition) is NOT mounted.;)
Check your /etc/fstab and /usr/local/.files.
wengi
r3ap3rpl
16-09-2008, 07:32
yes yes I know, RTFM :D
I wrote, without usb-hdd, internal flash only ;)
there's no fstab :/
in /usr/local: etc, root, sbin adn no files
In etc dir it's only dropbear dir, root is empty,
[root@WL-001BFC918B60 root]$ ls /usr/local/sbin/
post-boot post-firewall post-mount pre-mount pre-shutdown
all of this files are empty, only in post-boot is dropbear ;)
there's no fstab :/ what version of oleg did you flash?
This howto is for version 1.9.2.7-9 and newer.
And by the way: No USB HDD/Stick -> No /opt !!!
No woman -> No cry :)
wengi
r3ap3rpl
16-09-2008, 15:30
thanks a lot wengi ;)
I installed ver 1.9.2.7-9 (BCM47XX)
no usb-hdd no /opt, so I can't use ipkg and many other features...:(
It's the way to buy a usb-hdd :D
ok, thx
r3ap3rpl
biohazarduk
18-09-2008, 15:35
Cant get cron to auto start at boot been following the guide but too much of a newb with linux please help. Will start it manualy so I can continue for now.
My PS axf results
[admin@(none) root]$ ps axf
PID TTY STAT TIME COMMAND
1 ? S 0:01 /sbin/init
2 ? S 0:00 [keventd]
3 ? SN 0:00 [ksoftirqd_CPU0]
4 ? S 0:00 [kswapd]
5 ? S 0:00 [bdflush]
6 ? S 0:00 [kupdated]
7 ? S 0:00 [mtdblockd]
47 ? S 0:00 telnetd
48 ? S 0:00 httpd eth1
54 ? S 0:00 syslogd -m 0 -O /tmp/syslog.log -S -l 7
55 ? S 0:00 klogd
56 ? S 0:00 [dnsmasq]
58 ? Ss 0:01 nas /tmp/nas.lan.conf /tmp/nas.lan.pid lan
61 ? S 0:00 [khubd]
70 ? Ss 0:00 lpd
72 ? Ss 0:00 p9100d -f /dev/usb/lp0 0
75 ? Ss 0:00 waveservermain
77 ? Ss 0:00 rcamdmain
81 ? S 0:00 [usb-storage-0]
82 ? S 0:00 [scsi_eh_0]
86 ? Ss 0:00 infosvr br0
87 ? Ss 0:02 watchdog
91 ? Ss 0:00 \_ ntp
100 ? S 0:00 dropbear
107 ? Ss 0:01 \_ dropbear
113 pts/0 Rs 0:00 \_ -sh
129 pts/0 R+ 0:00 \_ ps axf
106 ? S 0:00 udhcpc -i eth1 -p /var/run/udhcpc0.pid -s /tmp/udhcpc
116 ? S 0:00 [kjournald]
117 ? S 0:00 [kjournald]
120 ? S 0:00 stupid-ftpd
127 ? S 0:00 upnp -D -L br0 -W eth1
My unslung
[admin@(none) root]$ vi /opt/etc/init.d/rc.unslung
# starting them in numerical order and
# stopping them in reverse numerical order
#
if [ $# -ne 1 ]; then
printf "Usage: $0 {start|stop}\n" >&2
exit 1
fi
daemons=`echo $(/usr/bin/dirname $0)/S??*`
[ $1 = "stop" ] && daemons=`echo $daemons | /usr/bin/tr " " "\n" | /usr/bin/sort
for i in $daemons; do
# Ignore dangling symlinks (if any).
[ ! -f "$i" ] && continue
# Write to syslog
logger -t rc.unslung "$1 service $i"
case "$i" in
*.sh)
# Source shell script for speed.
(
- /opt/etc/init.d/rc.unslung 1/34 2%
tarting them in numerical order and
# stopping them in reverse numerical order
#
if [ $# -ne 1 ]; then
printf "Usage: $0 {start|stop}\n" >&2
exit 1
fi
daemons=`echo $(/usr/bin/dirname $0)/S??*`
[ $1 = "stop" ] && daemons=`echo $daemons | /usr/bin/tr " " "\n" | /usr/bin/sort -r`
for i in $daemons; do
# Ignore dangling symlinks (if any).
[ ! -f "$i" ] && continue
# Write to syslog
logger -t rc.unslung "$1 service $i"
case "$i" in
*.sh)
# Source shell script for speed.
(
trap - INT QUIT TSTP
set $1
. $i
)
;;
*)
# No sh extension, so fork subprocess.
$i $1
;;
esac
done
My Post-boot only had the top 2 lines so I copied the rest from a post on the forum.
[admin@(none) root]$ vi /usr/local/sbin/post-boot
#!/bin/sh
dropbear
# test if USB disc has been attached
# if not - then insert needed modules
#
# uncoment the following 4 lines if using an USB HDD.
if [ ! -d /dev/discs ]
then
insmod scsi_mod && insmod sd_mod && insmod usb-storage && sleep 5s
fi
#Wait for /opt to mount
mount /dev/discs/disc0/part2 /opt
i=0
while [ $i -le 30 ]
do
if [ -d /opt/etc ]
then
break
fi
sleep 1
i=`expr $i + 1`
- /usr/local/sbin/post-boot 1/27 3%
#!/bin/sh
dropbear
# test if USB disc has been attached
# if not - then insert needed modules
#
# uncoment the following 4 lines if using an USB HDD.
if [ ! -d /dev/discs ]
then
insmod scsi_mod && insmod sd_mod && insmod usb-storage && sleep 5s
fi
#Wait for /opt to mount
mount /dev/discs/disc0/part2 /opt
i=0
while [ $i -le 30 ]
do
if [ -d /opt/etc ]
then
break
fi
sleep 1
i=`expr $i + 1`
done
Your original post-boot with the two lines is ok. Delete the rest again.
This was changed with firmewares -9 and newer.
Can you start cron manually?
Compare the content of /opt/etc/init.d/S10cron with the Howto.
wengi
biohazarduk
18-09-2008, 16:13
Update solved cron problem dont know how but ps axf shows
129 ? Ss 0:00 /opt/sbin/cron
Im on a wl-500w if that makes a difference. Thanks for your quick reply wengi, cron can be started manually. PS axf confirms it
Pre-manual start
[admin@(none) root]$ ps axf
PID TTY STAT TIME COMMAND
1 ? S 0:01 /sbin/init
2 ? S 0:00 [keventd]
3 ? SN 0:00 [ksoftirqd_CPU0]
4 ? S 0:00 [kswapd]
5 ? S 0:00 [bdflush]
6 ? S 0:00 [kupdated]
7 ? S 0:00 [mtdblockd]
47 ? S 0:00 telnetd
48 ? S 0:00 httpd eth1
54 ? S 0:00 syslogd -m 0 -O /tmp/syslog.log -S -l 7
55 ? S 0:00 klogd
56 ? S 0:00 [dnsmasq]
58 ? Ss 0:00 nas /tmp/nas.lan.conf /tmp/nas.lan.pid lan
61 ? S 0:00 [khubd]
70 ? Ss 0:00 lpd
72 ? Ss 0:00 p9100d -f /dev/usb/lp0 0
75 ? Ss 0:00 waveservermain
77 ? Ss 0:00 rcamdmain
81 ? S 0:00 [usb-storage-0]
82 ? S 0:00 [scsi_eh_0]
86 ? Ss 0:00 infosvr br0
87 ? Ss 0:02 watchdog
91 ? Ss 0:00 \_ ntp
100 ? S 0:00 dropbear
120 ? Rs 0:00 \_ dropbear
126 pts/0 Ss 0:00 \_ -sh
131 pts/0 R+ 0:00 \_ ps axf
108 ? S 0:00 udhcpc -i eth1 -p /var/run/udhcpc0.pid -s /tmp/udhcpc
115 ? S 0:00 upnp -D -L br0 -W eth1
121 ? S 0:00 [kjournald]
122 ? S 0:00 [kjournald]
124 ? S 0:00 stupid-ftpd
Post manual Start this line is added directly after 124
133 ? Ss 0:00 cron
Post boot edited too read
#!/bin/sh
dropbear
S10cron reads
#!/bin/sh
#
# Startup script for cron
PIDFILE=/opt/var/run/cron.pid
case $1 in
start)
/opt/sbin/cron
;;
stop)
[ -f ${PIDFILE} ] && kill `cat ${PIDFILE}` ;;
*)
echo "usage: $0 (start|stop)"
exit 1
esac
biohazarduk
18-09-2008, 19:47
Also solved but again dont know how
[admin@(none) torrent]$ mkdir /tmp/harddisk/torrent
cannot create directory `/tmp/harddisk/torrent': File exists
[admin@(none) torrent]$ mkdir /tmp/harddisk/torrent/source
cannot create directory `/tmp/harddisk/torrent/source': Read-only file system
[admin@(none) torrent]$ mkdir /tmp/harddisk/torrent/work
cannot create directory `/tmp/harddisk/torrent/work': Read-only file system
[admin@(none) torrent]$ mkdir /tmp/harddisk/torrent/target
cannot create directory `/tmp/harddisk/torrent/target': Read-only file system
[admin@(none) torrent]$ chmod -R ugoa+w /tmp/harddisk/torrent
changing permissions of `/tmp/harddisk/torrent': Read-only file system
Infomation from mount
[admin@(none) torrent]$ mount
/dev/root on / type squashfs (ro)
none on /dev type devfs (rw)
proc on /proc type proc (rw)
ramfs on /tmp type ramfs (rw)
usbfs on /proc/bus/usb type usbfs (rw)
/dev/discs/disc0/part2 on /opt type ext3 (rw,noatime)
/dev/discs/disc0/part3 on /tmp/harddisk type ext3 (rw,noatime)
/dev/discs/disc0/part1 on /tmp/harddisk type vfat (ro,noatime)
[admin@(none) torrent]$
/dev/discs/disc0/part3 on /tmp/harddisk type ext3 (rw,noatime)
/dev/discs/disc0/part1 on /tmp/harddisk type vfat (ro,noatime)
This is strange!!
your part1 should be swap and not data partition. And it must not be vfat if it is swap!
Did you setup the hdd different from the howto?
What is the output of 'free'?
wengi
mataanjin
03-10-2008, 09:40
how to change my listening port?
my isp blok some of my port(80 , 22 , 23)
when i use wget i can't get it download automatically.
how to get it work?
Hi,
Have a problem with accessing my router's Samba 2 settings on a port 901. Have installed Samba by wengi's tutorial, but than when typing "ps axf", don't see there line with "xinetd". When xinetd is not running, than I can't access 901, right?
Can anyone try to help me?
My output from "ps axf" is:
PID TTY STAT TIME COMMAND
1 ? S 0:01 /sbin/init
2 ? S 0:00 [keventd]
3 ? RN 0:00 [ksoftirqd_CPU0]
4 ? S 0:00 [kswapd]
5 ? S 0:00 [bdflush]
6 ? S 0:00 [kupdated]
7 ? S 0:00 [mtdblockd]
45 ? S 0:00 telnetd
50 ? S 0:01 httpd eth1
54 ? S 0:00 klogd
55 ? S 0:00 syslogd -m 0 -O /tmp/syslog.log -S -l 7
58 ? S 0:00 [dnsmasq]
60 ? Ss 0:01 nas /tmp/nas.lan.conf /tmp/nas.lan.pid lan
63 ? S 0:00 [khubd]
73 ? Ss 0:00 lpd
75 ? Ss 0:00 p9100d -f /dev/usb/lp0 0
79 ? S 0:00 [usb-storage-0]
80 ? S 0:00 [scsi_eh_0]
81 ? S 0:00 [usb-storage-1]
82 ? S 0:00 [scsi_eh_1]
95 ? Ss 0:00 infosvr br0
96 ? Ss 0:00 watchdog
100 ? Ss 0:00 \_ ntp
109 ? S 0:00 dropbear
191 ? Ss 0:00 \_ dropbear
199 pts/0 Ss 0:00 \_ -sh
208 pts/0 R+ 0:00 \_ ps axf
117 ? S 0:00 udhcpc -i eth1 -p /var/run/udhcpc0.pid -s /tmp/udhcpc
139 ? S 0:00 [kjournald]
140 ? S 0:00 [kjournald]
141 ? S 0:00 [kjournald]
144 ? Ss 0:00 /usr/sbin/vsftpd
155 ? Ss 0:00 /opt/sbin/cron
174 ? Ss 0:00 /opt/sbin/smbd -D
176 ? Ss 0:00 /opt/sbin/nmbd -D
197 ? S 0:00 upnp -D -L br0 -W eth1
how to change my listening port?
my isp blok some of my port(80 , 22 , 23)
when i use wget i can't get it download automatically.
how to get it work?
Hi,
which service?
Generally have a look at the conf files in /opt/etc
wengi
@Kubicz
check your rc.unslung and corresponding xinetd rc file.
Can you start xinetd manually? (with start/stop option?)
wengi
mataanjin
06-10-2008, 02:34
Hi,
which service?
Generally have a look at the conf files in /opt/etc
wengi
web service( to acsses my router )
shh(dropbear?)
@Kubicz
check your rc.unslung and corresponding xinetd rc file.
Can you start xinetd manually? (with start/stop option?)
wengi
Hi wengi,
Thanks a lot, problem solved - it was in a user settings, because I changed my root user, but not changed settings of corresponding files.
Now have another problem, I feel like noob, because I had to deal this situation year ago and now cannot remember, how have a solved it.
Samba is set, but I cannot access even a folders, because have security set to USER. When typing address of the router than bumps a window, where I can put a user name and password, but cannot access it.
Tried several things, have setted /opt/etc/samba/smbpasswd, where I have a password, but not working. When having security in smb.conf set to SHARE, it works, but I need to have it secured -> USER.
Thanks for help!
@ the forum Master -
Can this be stickyed - I am frightened it will depart from the landing page!! :D
Thanks Velcrow
(I keep referencing this post so it would be great to see it near the top)
Hi there,
been away some time.
Problems still current or solved in the meantime?
wengi
killerage
21-10-2008, 13:51
Hy wengie can you help me i have a problem with the listening port of transmission.I have to open the port from the asus or the asus automaticly opens the ports.Many thanks
"
[koper89@ROUTER root]$ free
total used free shared buffers cached
Mem: 30164 29284 880 0 596 21292
-/+ buffers/cache: 7396 22768
Swap: 524276 6740 517536
"
is this okay?? I must reboot my router often, when i use rtoorent.. is this usage of memory ok? or something is wrong?? How can i fix this??
Hy wengie can you help me i have a problem with the listening port of transmission.I have to open the port from the asus or the asus automaticly opens the ports.Many thanks
Depends on the network config.
- If your asus is directly connected to the inet you will have to open the port within iptables. (see Howto 14b, change port 22 to your transmission port)
- If another router is connecting to the internet you will have to open the port on this router.
@koper89
Looking good. Swap is used. I do not use rtorrent, so i can not help you that much...
wengi
is there web gui for transmission??
Yes. See bottom of chapter 9b.
wengi
killerage
22-10-2008, 12:31
I have a modem what is a router before the asus both all the ports are opened because the ip of the asus is in dmz zone....i want to disable completly the firewall , and learn hoe to open the ports if not.... pls help me:o:o
mataanjin
23-10-2008, 02:06
i want to access my box using ssh, but my isp block port 22.
how to redirect/forward incoming connection from 12222 to port 22?
is there possible in transmission, when i press log it's only
generate the graph(not showing the log file)?
if i turn off my firewall setting, post-firewall isn't executed?
in my transmission log i have this
Couldn't bind port 65534: Address already in use
Oct 22 13:47:46 transmissiond[1600]: Couldn't open port 65534 to listen for incoming peer connections (errno 125 - Address already in use)
Oct 22 13:47:46 transmissiond[1600]: Couldn't bind port 65534: Address already in use
Oct 22 13:47:46 transmissiond[1600]: Couldn't open port 65534 to listen for incoming peer connections (errno 125 - Address already in use)
Oct 22 13:47:46 transmissiond[1600]: Couldn't bind port 65534: Address already in use
Oct 22 13:47:46 transmissiond[1600]: Couldn't open port 65534 to listen for incoming peer connections (errno 125 - Address already in use)
what's the error, and how to correct it? i have open port 65534.
tq
I have a modem what is a router before the asus both all the ports are opened because the ip of the asus is in dmz zone....i want to disable completly the firewall , and learn hoe to open the ports if not.... pls help me:o:o
If you do not use your asus as router: Do NOT use "home gateway" mode.
This can be changed in the asus webinterface.
This will disable firewall, NAT and others...
wengi
@mataanjin
1. Do a forum search on how to redirect a port. this has been discussed several times.
2. "Address already in use" means Address already in use :)
You should have a look at ps if transmission is running several times (not the children!) or if another process is using thi port. try 'netstat' to list active ports.
wengi
Hi,
You con only eport rw if you have write rights!
/mnt is read-only:
[admin@blechbuechse /tmp]$ touch /mnt/temp
cannot touch `/mnt/temp': Read-only file system
Try to use /tmp/mnt.
wengi
@wengi and all
I have been able to get the mini_sendmail working - for all, like me, that did not know here are the commands -
printf 'Subject: The subject of the email \r\nThis is the body text of the email' |mini_sendmail -t -ftest@test.com -ssmtp.mail.com -v email@test.com
printf 'Subject: The subject of the email \r\nThis is the body text of the email'
This just creates the email, echo won't work because we need to use the "\r\n" to make a newline and return so that the Subject: and body text are separate.
-t (Im not sure why this is needed)
-f (the "from" email *note no space -f)
-s (your isps smtp server *note no space after -s)
-v (the recipient's email * note the space after -v)
Now what I would like to do is
Write a script that runs from cron that will send me an email when an event happens.
The event would be the completion of a torrent or a dropbear logon etc.
How would I do this - I am thinking that the script should check the syslog.log ever hour and extract the log messages that are of interest and send them on .....
Can someone (wengi :) ) give me some help on how to get this done.
Thanks
Velcrow
blueman2
17-11-2008, 01:38
I have transmission running using transmissioncli, but cannot get it to run correctly via the web interface. The web page comes up, but it does not trigger watchdog correctly, I think.
When I run transmission_watchdog at the telnet prompt, I get this message:
touch /.watchdog: Read-only file system
in the WEB page, I get the following when running watchdog:
touch: /.watchdog: Read-only file system BusyBox v1.1.3 (2008.03.17-18:24+0000) multi-call binary Usage: rm [OPTION]... FILE... /opt/sbin/transmission_watchdog: kill: 304: Usage: kill [-s sigspec | -signum | -sigspec] [pid | job]... or kill -l [exitstatus] transmissiond: option requires an argument -- i Usage: transmissiond [options] active-torrents.txt [options] Options: -h, --help Print this help and exit -v, --verbose Verbose level implies foreground (0 to 2, default = 0) -p, --port Port we should listen on (default = 51413) -u, --upload Maximum upload rate (-1 = no limit, default = 20) -d, --download Maximum download rate (-1 = no limit, default = -1) -f, --finish Command you wish to run on completion -n --nat-traversal Attempt NAT traversal using NAT-PMP or UPnP IGD -w, --watchdog Watchdog interval in seconds (default = 600) -i, --pidfile PID file path -e, --encryption Turns on encryption as preferred Signals: HUP reload active-torrents.txt and start/stop torrents USR1 write .status files into torrent directories USR2 list active torrents rm: cannot remove `/.watchdog': No such file or directory
Any ideas what I did wrong? Is there somewhere that I need to configure where the .watchdog file is located?
I am using 1.22-3 version of transmission.
blueman2
18-11-2008, 20:29
Well, I gave up on this, and downloaded the most recent version of Transmision (1.4) which integrates the web interface. It works perfectly! Just install via "ipkg install transmission", the launch with "transmission-daemon -w /path to where you want files"
Hi,
i have been away for some time.
It seems that transmissiond does not exist any longer!?!
I will figure this out when i have time for it...
wengi
EDIT: Howto will be updated in december.
mataanjin
22-11-2008, 02:09
i can't do ipkg update.
this is the error message.
Downloading http://ipkg.nslu2-linux.org/feeds/optware/oleg/cross/stable/Packages.gz
sh: wget: Permission denied
An error ocurred, return value: 1.
Collected errors:
ipkg_download: ERROR: Command failed with return value 127: `wget -q -P /opt/ipkg-AjnUBd http://ipkg.nslu2-linux.org/feeds/optware/oleg/cross/stable/Packages.gz'
how to correct this?
tq
Why doesn't part3 mount correctly?
[admin@ASUS ipkg]$ df
Filesystem 1K-blocks Used Available Use% Mounted on
rootfs 3072 3072 0 100% /
/dev/root 3072 3072 0 100% /
/dev/discs/disc0/part2
986104 73060 862952 8% /opt
/dev/discs/disc0/part3
479240116 131228 454764872 1% /tmp/mnt/disc0_3
[admin@ASUS ipkg]$ umount /tmp/mnt/disc0_3
[admin@ASUS ipkg]$ mount /dev/discs/disc0/part3 /tmp/harddisk
[admin@ASUS ipkg]$ df
Filesystem 1K-blocks Used Available Use% Mounted on
rootfs 3072 3072 0 100% /
/dev/root 3072 3072 0 100% /
/dev/discs/disc0/part2
986104 73060 862952 8% /opt
/dev/discs/disc0/part3
479240116 131228 454764872 1% /tmp/mnt/disc0_3
userouter
25-11-2008, 09:53
Why doesn't part3 mount correctly?
All right, this should be so
/tmp/harddisk link to /tmp/mnt/disc0_3
I get an error message:
[admin@ASUS root]$ /tmp/harddisk link to /tmp/mnt/disc0_3
-sh: /tmp/harddisk: Permission denied
userouter
25-11-2008, 11:28
I get an error message:
[admin@ASUS root]$ /tmp/harddisk link to /tmp/mnt/disc0_3
-sh: /tmp/harddisk: Permission denied
it does not need to enter )
Important: The data partition is mounted to /tmp/hardisk as in fstab. This is handled different in the firmware because of compatibility issues: The Partition is mounted to /tmp/mnt/disc0_3 and a symlink is pointing from /tmp/hardisk to /tmp/mnt/disc0_3
I did all the stepts before...
[admin@ASUS root]$ cat /etc/fstab
#device Mountpoint FStype Options Dump Pass#
/dev/discs/disc0/part1 none swap sw 0 0
/dev/discs/disc0/part2 /opt ext3 rw,noatime 1 1
/dev/discs/disc0/part3 /tmp/harddisk ext3 rw,noatime 1 1
but the partition isn't mounted. And i can't mount it even if i try it manualy.
trymyluck
25-11-2008, 23:08
After my first installation of Oleg's FW I need some help with Transmission...
When I enter command:
transmission_watchdog
as it is explained in the manual, I get:
-sh: transmission_watchdog: not found
When I enter command:
ps axf
I get:
[admin@WL-001BFC58826B root]$ ps axf PID TTY STAT TIME COMMAND
1 ? S 0:01 /sbin/init
2 ? S 0:00 [keventd]
3 ? SN 0:00 [ksoftirqd_CPU0]
4 ? S 0:00 [kswapd]
5 ? S 0:00 [bdflush]
6 ? S 0:00 [kupdated]
7 ? S 0:00 [mtdblockd]
59 ? S 0:00 telnetd
64 ? S 0:01 httpd vlan1
71 ? S 0:00 klogd
72 ? S 0:00 [dnsmasq]
77 ? S 0:00 [khubd]
86 ? Ss 0:00 lpd
88 ? Ss 0:00 p9100d -f /dev/usb/lp0 0
91 ? Ss 0:00 waveservermain
93 ? Ss 0:00 rcamdmain
97 ? S 0:00 [usb-storage-0]
98 ? S 0:00 [scsi_eh_0]
105 ? Ss 0:00 infosvr br0
106 ? Ss 0:00 watchdog
110 ? Ss 0:00 \_ ntp
126 ? S 0:00 udhcpc -i vlan1 -p /var/run/udhcpc0.pid -s /tmp/udhcp
129 ? S 0:00 dropbear
130 ? Ss 0:01 \_ dropbear
189 pts/0 Ss 0:00 \_ -sh
200 pts/0 R+ 0:00 \_ ps axf
136 ? S 0:00 upnp -D -L br0 -W vlan1
152 ? S 0:00 [kjournald]
153 ? S 0:00 [kjournald]
156 ? Ss 0:00 /usr/sbin/vsftpd
183 ? S 0:00 /sbin/syslogd -m 0 -O /opt/var/log/syslog.log -S -l 7
188 ? Ss 0:00 /opt/sbin/cron
The content of the following files is:
transmission.conf
#Uncomment the following for UPNP NAT traversal
#NAT_TRAVERSAL=--nat-traversal
# If the following limit is reached watchdog will not enqueue new one
MAX_ACTIVE_TORRENTS=5
SYSLOG=/opt/var/log/syslog.log
crontab
SHELL=/bin/sh
PATH=/sbin:/bin:/usr/sbin:/usr/bin:/opt/sbin:/opt/bin
MAILTO=""
HOME=/
# ---------- ---------- Default is Empty ---------- ---------- #
*/30 * * * * admin nice transmission_watchdog
0 0 * * * admin /opt/sbin/logrotate -f /opt/etc/logrotate.conf &>/dev/null
logrotate.conf
ompress
/opt/var/log/syslog.log {
size 1024k
weekly
rotate 9
postrotate
killall -HUP syslogd
endscript
}
include /opt/etc/logrotate.d
Please, what should I do to make it working? :(
I changed the FW just for the Torrents
@ trymyluck
remove transmissiond ( the one you are using ) and install transmission instead.
the 1.4 version is stable using clutch
http://wl500g.info/showthread.php?t=15562
trymyluck
26-11-2008, 09:19
@ trymyluck
remove transmissiond ( the one you are using ) and install transmission instead.
the 1.4 version is stable using clutch
http://wl500g.info/showthread.php?t=15562
Thank you for the information.
Please, consider me a beginner, what version should I install and where I can find it? Do I have to make any special settings after installing the older version, or what I did according to the manual will enough?
Another question I have, what is clutch in software terms?
examiner
27-11-2008, 11:35
Hi,
I used a guide here: http://wlhdd.co.uk/wiki/Adding_Users for adding users, but my share access doesn't work if I want to disable shell for this user. telnet says:
WL500W login: share
Password:
login: cannot run /sbin/nologin: No such file or directory
what's wrong? :(
trymyluck
27-11-2008, 13:05
Hi all,
I know that being a newbie is annoying, but everyone of you was a newbie before turning into an expert :-)
So, could you please help me with the Transmission?
I need to install Transmission on my router. I'm using Oleg's FW 1.9.2.7-10, which I installed according to this manual.
During the installation everything went great till Transmission installation, then I found out that the manual doesn't correspond with the latest version, that is on Oleg's repository.
What should I do to get it working?
I'm not able to find any older version, that would work according to this manual.
One more question, is there anybody using TorrentFlux (http://ipkg.nslu2-linux.org/feeds/optware/oleg/cross/stable/torrentflux_2.4-5_mipsel.ipk)? It looks really nice.
Recently I updated my Asus WL-500gP with a new WL-500W.
I updated from Oleg's FW 1.9.2.7-8 to 1.9.2.7-10.
Everything works fine (same HDD as before with /opt on it), but I'm in doubt about a couple of things. I used vsftp and samba2 (s2 is running under xinetd) installed with ipkg.
Latest Oleg's firmware has vsftp on it and a Samba version that can be handled by Microsoft Vista.
Can I remove ipkg installed software and use the built in modules ?
Is there a way to use actual cfg files for vsftp and samba2 with built in modules ?
Thanks for your help.
Max
Hi@all,
News for the hanging of transmission webinterface:
Do the following:
Install the shell "bash".
ipkg install bash
Edit transmission.cgi. First line to be replaced with:
#!/opt/bin/bashdone.
technical background: The integrated busybox shell and transmission.cgi do not work 100% ok. The exact problem is not pointed out until now.
29.06.2008
wengi
Hi !
bash depend on libiconv library, you must install it
ipkg install libiconv
I have a WL520GU. How would I allow remote access to the UI ? I would think its related to SNMP - but totally at a loss about how to go about it. Does anyone know how to allow remote management to my WL520GU access so a technician can debug why my VOip is not working behind it ?
Thanks!
Hi to all !
i have a little problem posted here :
http://wl500g.info/showthread.php?p=120412#post120412
if someone can help me , i will apreciate !
Thx
Does anyone know where i can find a tutorial on how to install the latest version of transmission? A complete tutorial of how to set up my router wold be preffered. Thank you.
Does anyone know where i can find a tutorial on how to install the latest version of transmission? A complete tutorial of how to set up my router wold be preffered. Thank you.
Start from this topic (http://wl500g.info/showthread.php?t=5909) (skip transmission part).
Click (http://wl500g.info/showpost.php?p=108370&postcount=30) for transmission 1.3+ tutorial.
It doesn't work. I've noticed that the current transmission version is 1.42b, does it matter?
It doesn't work. I've noticed that the current transmission version is 1.42b, does it matter?
It doesn't matter.
What's the problem?
I installed transmission but the webinterface doesn't open.
I installed transmission but the webinterface doesn't open.
Is transmission-daemon running (e.g. top command)?
Have you fallowed all steps in this post (http://wl500g.info/showpost.php?p=108370&postcount=30)?
How link you are trying to open looks like?
Are you looking to install the version with clutch ( JavaScript, Ajax) version 1.41 or the older 1.32 version?
I just want a version that works, the available one is 1.4b
The link to open the webinterface is http://192.168.1.1:8008/transmission/web
It doesn't work, even if i try the wan ip address. :(
Anyone know where i can find a complete tutorial? :D
userouter
12-12-2008, 19:27
this is code of this is tutorial
highlighted in red - error? or not?
9b. Change Syslog settings
#!/bin/sh
#
# Startup script for syslog
#
PATH=/opt/bin:/opt/sbin:/opt/local/bin:/sbin:/bin:/usr/bin:/usr/sbin
LOGFILE=syslog.log
KERNLOGFILE=kern.log
LOG_OLD=/tmp
LOG_NEW=/opt/var/log
prefix=""
sbindir=${prefix}/sbin
NAME=syslogd
DAEMON=${sbindir}/${NAME}
DESC="syslogd"
OPTIONS="-m 0 -O $LOG_NEW/$LOGFILE -S -l 7 -s 0"
case "$1" in
start0)
printf "Starting ${DESC}: "
# Copy old syslog and create symlink to new
if [ ! -L /tmp/syslog.log ]; then
cat $LOG_OLD/$LOGFILE >> $LOG_NEW/$LOGFILE
mv $LOG_OLD/$LOGFILE $LOG_NEW/$KERNLOGFILE
ln -s $LOG_NEW/$LOGFILE $LOG_OLD/$LOGFILE
fi
${DAEMON} ${OPTIONS}
printf "${NAME}.\n"
logger -t ${NAME} "started."
;;
stop)
if [ -n "`pidof syslogd`" ]; then
printf "Stopping ${DESC}: "
killall "${NAME}"
printf "${NAME}.\n"
fi
;;
start|restart|force-reload)
$0 stop
sleep 1
$0 start0
;;
*)
printf "Usage: $0 {start|stop|restart|force-reload}\n" >&2
exit
;;
esac
exit 0
userouter
12-12-2008, 19:59
The script will create archives
/opt/var/log/syslog.log.tar.gz and /opt/opt/share/www/access.log.tar.gz ???
take
9b. Change Syslog settings
vi /opt/etc/logrotate.conf
compress
/opt/var/log/syslog.log {
size 1024k
weekly
rotate 9
postrotate
killall -HUP syslogd
endscript
}
/opt/opt/share/www/access.log {
size 1024k
weekly
rotate 9
postrotate
killall -HUP syslogd
endscript
}
include /opt/etc/logrotate.d
When i try to run transmission (1.41b3) i have error:
can't resolve symbol '__libc_pthread_init
transmission 1.40 works for me.
What i must to do ?
Hi all,
the howto is updated for transmission versions newer than 1.3.
I also renumbered the chapters.
Please report bugs.
@Lesiuk
Sorry, i do not get these errors. I even can not help.
Sorry
wengi
Hi all,
the howto is updated for transmission versions newer than 1.3.
I also renumbered the chapters.
Please report bugs.
@Lesiuk
Sorry, i do not get these errors. I even can not help.
Sorry
wengi
Now there is no transmission in repository...
Downloading http://ipkg.nslu2-linux.org/feeds/optware/oleg/cross/stable/transmission_1.41b3-2_mipsel.ipk
wget: server returned error 404: HTTP/1.1 404 Not Found
Somebody remove it...
Hi,
there seems to be a build problem.
Wait till tomorow/some days.
wengi
Hi,
there seems to be a build problem.
Wait till tomorow/some days.
wengi
I have another problem:
When I put "http://ASUSIPADRESS:9091"
I have:
401: Unauthorized
Unauthorized IP Address
And i have no webinterface
Please help me.
Hi,
i updated 15 mins ago and run into the same problem.
Have no solution jet.
wengi
Hi,
i updated 15 mins ago and run into the same problem.
Have no solution jet.
wengi
I have solution.
http://forum.transmissionbt.com/viewtopic.php?f=1&t=6659
Now i have transmission web.
:D
alexanek
17-12-2008, 19:12
401: Unauthorized
Unauthorized IP Address
401: Unauthorized
Unauthorized IP Address
1- Stop transmission
killall transmission-daemon
2- Edit the settings.json file:
*- go to string "rpc-whitelist": "+127.0.0.1",
*- fix the value (+127.0.0.1) to your computer IP (i.e. 192.168.1.*) or just delete this value( i.e. "rpc-whitelist": "",)
3- Launch transmission (or reboot router)
Hi,
the reason is that my transmission does not create the settings.json any more.
Not on the hdd and not in the users home .config folder.
[admin@blechbuechse /]$ ps axf
PID TTY STAT TIME COMMAND
1 ? S 0:03 /sbin/init
2 ? S 0:00 [keventd]
...
127 ? Ss 0:04 /opt/sbin/cron
270 ? SN 0:36 /opt/bin/transmission-daemon -g /tmp/harddisk/transmission/config -b -w /tmp/harddisk/transmission/download
271 ? SN 0:00 \_ /opt/bin/transmission-daemon -g /tmp/harddisk/transmission/config -b -w /tmp/harddisk/transmission/download
272 ? RN 0:00 \_ /opt/bin/transmission-daemon -g /tmp/harddisk/transmission/config -b -w /tmp/harddisk/transmission/download
273 ? RN 4:34 \_ /opt/bin/transmission-daemon -g /tmp/harddisk/transmission/config -b -w /tmp/harddisk/transmission/download
[admin@blechbuechse /]$ find / | grep -i settings.json
/proc/7/fd: No such file or directory
[admin@blechbuechse /]$
No idea why. The settings file is not part of the package.
[admin@blechbuechse .config]$ ipkg files transmission | grep -i set
[admin@blechbuechse .config]$
Could you please post the content and location of your settings.json?
Thanks
wengi
Hi
I have setting.json on harddisk in config folder.
My transmission work about 10 min. and after don`t work properly.
Please I` need help.
Hi,
the reason is that my transmission does not create the settings.json any more.
Not on the hdd and not in the users home .config folder.
[admin@blechbuechse /]$ ps axf
PID TTY STAT TIME COMMAND
1 ? S 0:03 /sbin/init
2 ? S 0:00 [keventd]
...
127 ? Ss 0:04 /opt/sbin/cron
270 ? SN 0:36 /opt/bin/transmission-daemon -g /tmp/harddisk/transmission/config -b -w /tmp/harddisk/transmission/download
271 ? SN 0:00 \_ /opt/bin/transmission-daemon -g /tmp/harddisk/transmission/config -b -w /tmp/harddisk/transmission/download
272 ? RN 0:00 \_ /opt/bin/transmission-daemon -g /tmp/harddisk/transmission/config -b -w /tmp/harddisk/transmission/download
273 ? RN 4:34 \_ /opt/bin/transmission-daemon -g /tmp/harddisk/transmission/config -b -w /tmp/harddisk/transmission/download
[admin@blechbuechse /]$ find / | grep -i settings.json
/proc/7/fd: No such file or directory
[admin@blechbuechse /]$
No idea why. The settings file is not part of the package.
[admin@blechbuechse .config]$ ipkg files transmission | grep -i set
[admin@blechbuechse .config]$
Could you please post the content and location of your settings.json?
Thanks
wengi
In your case, the setting file should be in /tmp/harddisk/transmission/config
Example of file contents HERE (http://forum.transmissionbt.com/viewtopic.php?p=32421&sid=26cf206ef799df123f30f314c747838e#p32421)
In your case, the setting file should be in /tmp/harddisk/transmission/config
Example of file contents HERE (http://forum.transmissionbt.com/viewtopic.php?p=32421&sid=26cf206ef799df123f30f314c747838e#p32421)
transmission-daemon -a yourip
but i have another problem.
when i run transmission and add more than 1 torrent to download then transmission crash
Beta version...it figures. :( I'm waiting for the final version.
Cheers!
Who is making package's for optware repository?
Do somebody have 1.41b3 ?
Hi all,
i once again updated the HowTo:
Transmission is working with a config file now.
The startup script knows the option restart now.
@Lesiuk
Try this config with the newest version of transmission.
I wish all of you a happy new year!
wengi
Works fine, thank you. Again. :D
One question: What's the password for Samba? When i try to open http://192.168.1.1:901/ i get
401 Bad Authorization
username or password incorrect
although i used the password set for the router interface.
LE: Everything works, if only the user wasn't a n00b. :D
Dear Wengi,
Many thanks for your great HowTo! I've managed to format the HDD.
Unfortunately, I can get Transmission working on my setup (WL-500W with Oleg 1.9.2.7-10 and an USB memory card or USB-HDD).
I get the following error when starting S90transmission-daemon:
/opt/etc/init.d/S90transmission-daemon: /opt/etc/init.d/S90transmission-daemon: 36: /tmp/harddisk/transmission/config: Permission denied
transmission-daemon is not started according to ps axf.
When starting transmission with "$transmission-daemon", or
$transmission-daemon -g /tmp/harddisk/transmission/config the program starts, but I get the following error when I try to enter 192.168.1.1:9091
401: Unauthorized
Unauthorized IP Address.
Either disable the IP address whitelist or add your address to it.
If you're editing settings.json, see the 'rpc-whitelist' and 'rpc-whitelist-enabled' entries.
If you're still using ACLs, use a whitelist instead. See the transmission-daemon manpage for details.
I've tried changing the rpc-whitelist, in the settings.json, but without success.
I have followed your HowTo, but cannot figure out what Permission is denied?!?
edit: "chmod a +rwx" the settings file and download directory also did not help
Check your instalation again, you probably missed something.
Is there a limit to the number of torrents that Transmission can hadle?
skylin3d
05-01-2009, 14:40
I have the same problem, it says like this:
/opt/etc/init.d/S90transmission-daemon: /opt/etc/init.d/S90transmission-daemon: 36: /tmp/harddisk/transmission/config: Permission denied
[admin@asus root]$ ps axf
BusyBox v1.1.3 (2008.04.25-08:17+0000) multi-call binary
Usage: ps
Hi,
please check the permissions of /tmp/harddisk/transmission/config
Should be something like
[admin@blechbuechse root]$ ls -la /tmp/harddisk/transmission
total 16
drwxrwx--- 4 admin root 4096 Dec 13 22:47 .
drwxr-xr-x 5 admin root 4096 Dec 14 00:24 ..
drwxrwx--- 5 admin root 4096 Dec 21 18:18 config
drwxrwx--- 3 admin root 4096 Dec 14 13:21 download
[admin@blechbuechse root]$
Make sure you have read/write permission.
If not, execute:
chmod -R 770 /tmp/harddisk/transmission/
wengi
skylin3d
07-01-2009, 15:01
Hello, I still have the same problem, chmod didn't help.
mine looks like this:
[admin@asus root]$ ls -la /tmp/harddisk/transmission
drwxrwx--- 1 admin root 0 Jan 5 15:27 .
drwxr-xr-x 1 admin root 0 Jan 5 15:19 ..
drwxrwx--- 1 admin root 0 Jan 5 15:27 config
drwxrwx--- 1 admin root 0 Jan 5 15:27 download
Hi,
please post result of
ls -la /tmp/harddisk/transmission/config
wengi
skylin3d
07-01-2009, 18:05
It says:
[admin@asus root]$ ls -la /tmp/harddisk/transmission/config
drwxrwx--- 1 admin root 0 Jan 5 15:27 .
drwxrwx--- 1 admin root 0 Jan 5 15:27 ..
drwxrwx--- 1 admin root 0 Jan 5 15:27 blocklists
-rwxrwx--- 1 admin root 474 Jan 5 15:28 settings.json
[admin@asus root]$
Hi,
strange... Same permissions here. Working fine.
Please post content of
cat /opt/etc/init.d/S90transmission-daemon
What happens if you start it manually?
/opt/bin/transmission-daemon -g /tmp/harddisk/transmission/config
wengi
skylin3d
09-01-2009, 17:10
Hello, here are the results:
[admin@asus root]$ cat /opt/etc/init.d/S90transmission-daemon
#!/bin/sh
#
# Startup script for transmission-daemon
case $1 in
start)
# update blocklist
echo "updating blocklist, ~4MB"
cd /tmp/harddisk/transmission/config/blocklists
wget -q http://www.bluetack.co.uk/config/level1.gz
if test -f level1.gz; then
rm level1
gunzip level1.gz
chmod go+r level1
fi
# start transmission
echo "starting transmission"
/opt/bin/transmission-daemon -g
/tmp/harddisk/transmission/config
;;
stop)
if [ -n "`pidof transmission-daemon`" ]; then
kill -9 `pidof transmission-daemon`
fi
;;
restart)
$0 stop
$0 start
;;
*)
echo "usage: $0 (start|stop|restart)"
exit 1
esac
[admin@asus root]$
and:
[admin@asus root]$ /opt/bin/transmission-daemon -g /tmp/harddisk/transmission/config
/opt/bin/transmission-daemon: illegal option -- g
usage: transmission-daemon [-dfh] [-p file] [-s file]
Transmission 0.82 (r) http://transmission.m0k.org/
A free, lightweight BitTorrent client with a simple, intuitive interface
-d --debug Print data send and received, implies -f
-f --foreground Run in the foreground and log to stderr
-h --help Display this message and exit
-p --pidfile <path> Save the process id in a file at <path>
-s --socket <path> Place the socket file at <path>
To add torrents or set options, use the transmission-remote program.
[admin@asus root]$
Hi,
first: Do an update of your system:
ipkg update
ipkg upgrade
You are using a REAL old version of transmission.
New versions are 1.4x.
If the above does not update transmission do the following:
ipkg remove transmission
ipkg install transmission
second:
Make sure that this is ONE line in S90transmission-daemon
/opt/bin/transmission-daemon -g /tmp/harddisk/transmission/configI think you have this code in two lines.
wengi
drevnerussky
11-01-2009, 02:54
hi,
I have used the older version of transmission before, the older interface has more information(files, download speed record...). Where can i find these information in the new version?
thanks
ps. sorry for my English.
Hi,
all these informations can be found in the webinterface (clutch).
simply give it a try.
wengi
swordfish77
11-01-2009, 22:36
Hello everyone! I try to setup transmission,at the end i copy syntax for start-up script and when i try to save and exit with :wq ,the vi editor reports me this: write error: No such file or directory. Can help me someone? Thank u.:confused:
2swordfish77
I guess you have to create file first with touch
How can i find out what transmission version is available for download?
@lapcat:
http://nslu2-linux.dyoung-mirror.net/feeds/optware/oleg/cross/stable/
@swordfish77:
What exactly do you do? (step by step)
wengi
swordfish77
12-01-2009, 15:36
to Wengi,
- Create start-up script:
1.vi /opt/etc/init.d/S90transmission-daemon
2. start edit mode in vi with "I"
3.Copy ALL content of "Code"
4.Esc. ->Then i try to save all of this with "wq" : "Write error: No such file or directory" (please see the atach.)
Only with "q!" i can exit, of course without save...
Thank U!
P.S. - maybe some parameter interfer with "vi" commands?
Hi,
@ALL
one general thing to all:
If you paste scripts from the forum to the asus via putty and your lines are "shifted" like the pictures above:
The reason is because of the windows formating.
To prevent this behaviour you can copy the content to an editor that is linux capable (i.e. notepad++ (http://notepad-plus.sourceforge.net)) and change the format to unix (i.e. notepad++: format -> convert to unix).
After this you can paste the content properly.
@swordfish77
is the file created if you touch it? (idea of al37919 above)
touch /opt/etc/init.d/S90transmission-daemon
wengi
swordfish77
12-01-2009, 16:02
@Wengi,
No, "cannot touch `/opt/etc/init.d/S90transmission-daemon': No such file or directory"
Wengi,
I still get the permission denied message:
/opt/etc/init.d/S90transmission-daemon: /opt/etc/init.d/S90transmission-daemon: 36: /tmp/harddisk/transmission/config: Permission denied
I've also reinstalled transmission, but without result.
I do have read/write access:
$ ls -la /tmp/harddisk/transmission/config
drwxrwxrwx 5 admin root 4096 Jan 4 00:04 .
drwxrwxrwx 4 admin root 4096 Jan 3 22:42 ..
drwxrwxrwx 2 admin root 4096 Jan 12 19:27 blocklists
drwxrwxrwx 2 admin root 4096 Jan 3 23:01 resume
-rwxrwxrwx 1 admin root 497 Jan 12 19:19 settings.json
-rw-r--r-- 1 admin root 132 Jan 12 19:19 stats.json
drwxrwxrwx 2 admin root 4096 Jan 3 23:01 torrents
$ ls -la /tmp/harddisk/transmission
drwxrwxrwx 4 admin root 4096 Jan 3 22:42 .
drwxr-xr-x 7 admin root 4096 Jan 4 12:05 ..
drwxrwxrwx 5 admin root 4096 Jan 4 00:04 config
drwxrwxrwx 2 admin root 4096 Jan 3 22:42 download
$ cat /opt/etc/init.d/S90transmission-daemon
#!/bin/sh
#
# Startup script for transmission-daemon
case $1 in
start)
# update blocklist
echo "updating blocklist, ~4MB"
cd /tmp/harddisk/transmission/config/blocklists
wget -q http://www.bluetack.co.uk/config/level1.gz
if test -f level1.gz; then
rm level1
gunzip level1.gz
chmod go+r level1
fi
# start transmission
echo "starting transmission"
/opt/bin/transmission-daemon -g
/tmp/harddisk/transmission/config
;;
stop)
if [ -n "`pidof transmission-daemon`" ]; then
kill -9 `pidof transmission-daemon`
fi
;;
restart)
$0 stop
$0 start
;;
*)
echo "usage: $0 (start|stop|restart)"
exit 1
esac
Also:
$touch /opt/etc/init.d/S90transmission-daemon
does not give any output when transmission is started using
/opt/bin/transmission-daemon -g /tmp/harddisk/transmission/config
I don't know if that's a problem?
@swordfish77
Is your hdd mounted to /opt?
Does /opt/etc/init.d exist?
Did you use my howto from beginning?
Which firmware version?
@quazar
it is normal that
/opt/bin/transmission-daemon -g /tmp/harddisk/transmission/configdoes not give an output.
is transmission running after that? (ps)
wengi
swordfish77
13-01-2009, 16:50
I don't have init.d ...:( .I use Oleg's 1.9.2.7-10 firmware. And yes, i follow your post (btw - it's gold for me! Thk.v.much!).
I don't have init.d ...:( .I use Oleg's 1.9.2.7-10 firmware. And yes, i follow your post (btw - it's gold for me! Thk.v.much!).
Probably you need to read once again carefully point 5. from wengi's instruction. It is explained there how and where to create init.d directory. You cant perform 10. without ensuring that 5. is done correctly
swordfish77
13-01-2009, 17:30
Thank U, it worked! Now i installed Transmission-Remote GUI and can't connect..It's something i wanna do?
Edit: I solve the problem: In Transm.Remote -GUI -> Options ->Remote host, i change "localhost" with server IP adress. And the torrents works, but not have the usual speed..maybe need some setups. What i see , at Upload tab nothing work;maybe after complete download then start upload?
@quazar
it is normal that
Code:
/opt/bin/transmission-daemon -g /tmp/harddisk/transmission/config
does not give an output.
is transmission running after that? (ps)
the program starts, but I get the following error when I try to enter 192.168.1.1:9091
401: Unauthorized
Unauthorized IP Address.
Either disable the IP address whitelist or add your address to it.
If you're editing settings.json, see the 'rpc-whitelist' and 'rpc-whitelist-enabled' entries.
If you're still using ACLs, use a whitelist instead. See the transmission-daemon manpage for details.
I've tried changing the rpc-whitelist, in the settings.json, but without success.
Update 08-Mar-09: I ve got Transmission working now.
Wengi's comment:
Make sure that this is ONE line in S90transmission-daemon
/opt/bin/transmission-daemon -g /tmp/harddisk/transmission/config
made much sense; somehow both vi and nano pasted the text into two seperate lines, thatś when you get the permission denied error.
@swordfish77
fine :)
@quazar
Did you use my settings.json?
i enable all IPs within 129.168.*.* and 10.*.*.*
What is the IP Adress of your client?
Add this IP in settings.
wengi
I used the settings of the howto in settings.json.
My WL500W IP address is 192.168.1.1, so 192.168.*.* in the white list should work. Adding 192.168.1.1 to the settings-file does not help (as was tobe expected).
drevnerussky
15-01-2009, 09:36
Hi, Wengi
Sorry for this stupid question, how to use clutch?
I searched google for Clutch, and found this page:http://clutchbt.com/
I downloaded the webui source. when i opened index.html, i looks the same as my transmission interface. I still can't find the information.
Can you give me more details? thanks a lot.
Bohlendach
17-01-2009, 14:52
Hi Wengi.
Thx a lot for this awesome guide. :)
You wrote:
11. Logrotate for Syslog
Add the following to crontab:
0 0 * * * admin /opt/sbin/logrotate -f /opt/etc/logrotate.conf &>/dev/null
However, crontab is not mentioned elsewhere. It would be better if you write:
Edit crontab:
vi /opt/etc/crontab
and add the following:
0 0 * * * admin /opt/sbin/logrotate -f /opt/etc/logrotate.conf &>/dev/null
Thank you.
i changed the syslog chapter and added a hint to crontab in the cron chapter.
wengi
drevnerussky
18-01-2009, 11:26
hi,
I've had a new problem. Recently when i use transmission, the speed became very slow (about 10kb/s), but when i use my pc (with Deluge), i have 100kb/s. What's wrong? i use this torrent http://thepiratebay.org/torrent/4654899/Star_Wars_The_Clone_Wars_S01E13_HDTV_XviD-SC-SDH
BTW, how do i use Clutch?
thanks a lot
skylin3d
23-01-2009, 19:58
Hello,
I have one problem with Transmission, if I reboot the wl-500gp, /tmp/harddisk/transmission/config/settings.json doesn't exist anymore. And for that reason, the web gui says "401: Unauthorized Either disable the IP address whitelist or add your address to it. etc...".
So how can I get the file to stay also after rebooting the device? I've done everything as the instructions say, and Transmission works fine until reboot. Transmission is not shown if I use the ps axf command even before rebooting the device, does anyone know why?
Hi,
this is strange because you edit directly on your hdd.
And transmission should be shown by ps.
No idea why the file is deleted....
wengi
skylin3d
25-01-2009, 19:57
Hi,
I think it has something to do with the /tmp/ directory? Is it possible that things in /tmp gets erased or something? So would saving the file somewhere else than in /tmp resolve the problem..?