Senior Member
Написано же: megatec.cOriginally Posted by kvazimoda24
Вообще, мы собираемся отказаться от megatec/megatec_usb в пользу blazer_ser/blazer_usb, но фикс, я надеюсь, скоро попадет в svn.
blazer_usb должен работать сразу.
P.S. все задержки лучше вообще убрать, т.е. вычистить все места, где используется READ_PACE.
Last edited by Xander; 08-06-2009 at 13:58.
Junior Member
Еще раз дико извеняюсь. Но у меня никак не получается собрать NUT. Изменения я внёс в файл megatec.c, установил пакет buildroot. Дальше выполняю команду # ./configure --build=mips (пробовал также # ./configure --build=mipsel), после этого даю команду # make и она стопорится на сборке драйверов, вот вывод:
Вот не знаю, вроде стопорится на драйвере, который мне нафиг не нужен, но в тоже время я не знаю как собрать отдельно megatec и megatec_usb. Или, может надо что-то подправить в этом драйвере, чтобы он собрался нормально? Сразу говорю, что в программировании полный ноль, пока только осилил скрипты на basheCode:# make Making all in include make[1]: Entering directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/include' NUT_VERSION: "2.4.1" test -f nut_version.h || cp _nut_version.h nut_version.h cmp -s _nut_version.h nut_version.h || cp _nut_version.h nut_version.h rm -f _nut_version.h make all-am make[2]: Entering directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/include' make[2]: Leaving directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/include' make[1]: Leaving directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/include' Making all in common make[1]: Entering directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/common' (cd ../include/ && make nut_version.h) make[2]: Entering directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/include' NUT_VERSION: "2.4.1" test -f nut_version.h || cp _nut_version.h nut_version.h cmp -s _nut_version.h nut_version.h || cp _nut_version.h nut_version.h rm -f _nut_version.h make[2]: Leaving directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/include' make[1]: Leaving directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/common' Making all in clients make[1]: Entering directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/clients' make[1]: Nothing to be done for `all'. make[1]: Leaving directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/clients' Making all in conf make[1]: Entering directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/conf' make[1]: Nothing to be done for `all'. make[1]: Leaving directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/conf' Making all in data make[1]: Entering directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/data' Making all in html make[2]: Entering directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/data/html' make[2]: Nothing to be done for `all'. make[2]: Leaving directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/data/html' make[2]: Entering directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/data' make[2]: Nothing to be done for `all-am'. make[2]: Leaving directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/data' make[1]: Leaving directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/data' Making all in docs make[1]: Entering directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/docs' make[1]: Nothing to be done for `all'. make[1]: Leaving directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/docs' Making all in drivers make[1]: Entering directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/drivers' /opt/bin/bash ../libtool --tag=CC --mode=link gcc -I../include -I/opt/include -g -O2 -Ulinux -Dlinux=linux -O2 -pipe -I/home/slug/optware/oleg/staging/opt/include -I. -I/opt/include -D_LARGEFILE64_SOURCE -DNE_LFS -I/opt/include/neon -O -Wall -Wsign-compare -o bcmxcp bcmxcp.o bcmxcp_ser.o ../common/libcommon.a ../common/libparseconf.la main.o dstate.o serial.o libtool: link: gcc -I../include -I/opt/include -g -O2 -Ulinux -Dlinux=linux -O2 -pipe -I/home/slug/optware/oleg/staging/opt/include -I. -I/opt/include -D_LARGEFILE64_SOURCE -DNE_LFS -I/opt/include/neon -O -Wall -Wsign-compare -o bcmxcp bcmxcp.o bcmxcp_ser.o main.o dstate.o serial.o ../common/libcommon.a ../common/.libs/libparseconf.a bcmxcp.o: In function `decode_meter_map_entry': /tmp/mnt/disc0_3/Temp/nut-2.4.1/drivers/bcmxcp.c:608: undefined reference to `ldexp' bcmxcp.o: In function `get_float': /tmp/mnt/disc0_3/Temp/nut-2.4.1/drivers/bcmxcp.c:224: undefined reference to `ldexp' /tmp/mnt/disc0_3/Temp/nut-2.4.1/drivers/bcmxcp.c:231: undefined reference to `ldexp' collect2: ld returned 1 exit status make[1]: *** [bcmxcp] Error 1 make[1]: Leaving directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/drivers' make: *** [all-recursive] Error 1
Senior Member
./configure --prefix=/opt --with-drivers=megatec,megatec_usbЕще раз дико извеняюсь. Но у меня никак не получается собрать NUT. Изменения я внёс в файл megatec.c, установил пакет buildroot. Дальше выполняю команду # ./configure --build=mips (пробовал также # ./configure --build=mipsel), после этого даю команду # make и она стопорится на сборке драйверов, вот вывод:
Вот не знаю, вроде стопорится на драйвере, который мне нафиг не нужен, но в тоже время я не знаю как собрать отдельно megatec и megatec_usb. Или, может надо что-то подправить в этом драйвере, чтобы он собрался нормально? Сразу говорю, что в программировании полный ноль, пока только осилил скрипты на basheCode:# make Making all in include make[1]: Entering directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/include' NUT_VERSION: "2.4.1" test -f nut_version.h || cp _nut_version.h nut_version.h cmp -s _nut_version.h nut_version.h || cp _nut_version.h nut_version.h rm -f _nut_version.h make all-am make[2]: Entering directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/include' make[2]: Leaving directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/include' make[1]: Leaving directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/include' Making all in common make[1]: Entering directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/common' (cd ../include/ && make nut_version.h) make[2]: Entering directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/include' NUT_VERSION: "2.4.1" test -f nut_version.h || cp _nut_version.h nut_version.h cmp -s _nut_version.h nut_version.h || cp _nut_version.h nut_version.h rm -f _nut_version.h make[2]: Leaving directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/include' make[1]: Leaving directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/common' Making all in clients make[1]: Entering directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/clients' make[1]: Nothing to be done for `all'. make[1]: Leaving directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/clients' Making all in conf make[1]: Entering directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/conf' make[1]: Nothing to be done for `all'. make[1]: Leaving directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/conf' Making all in data make[1]: Entering directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/data' Making all in html make[2]: Entering directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/data/html' make[2]: Nothing to be done for `all'. make[2]: Leaving directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/data/html' make[2]: Entering directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/data' make[2]: Nothing to be done for `all-am'. make[2]: Leaving directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/data' make[1]: Leaving directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/data' Making all in docs make[1]: Entering directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/docs' make[1]: Nothing to be done for `all'. make[1]: Leaving directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/docs' Making all in drivers make[1]: Entering directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/drivers' /opt/bin/bash ../libtool --tag=CC --mode=link gcc -I../include -I/opt/include -g -O2 -Ulinux -Dlinux=linux -O2 -pipe -I/home/slug/optware/oleg/staging/opt/include -I. -I/opt/include -D_LARGEFILE64_SOURCE -DNE_LFS -I/opt/include/neon -O -Wall -Wsign-compare -o bcmxcp bcmxcp.o bcmxcp_ser.o ../common/libcommon.a ../common/libparseconf.la main.o dstate.o serial.o libtool: link: gcc -I../include -I/opt/include -g -O2 -Ulinux -Dlinux=linux -O2 -pipe -I/home/slug/optware/oleg/staging/opt/include -I. -I/opt/include -D_LARGEFILE64_SOURCE -DNE_LFS -I/opt/include/neon -O -Wall -Wsign-compare -o bcmxcp bcmxcp.o bcmxcp_ser.o main.o dstate.o serial.o ../common/libcommon.a ../common/.libs/libparseconf.a bcmxcp.o: In function `decode_meter_map_entry': /tmp/mnt/disc0_3/Temp/nut-2.4.1/drivers/bcmxcp.c:608: undefined reference to `ldexp' bcmxcp.o: In function `get_float': /tmp/mnt/disc0_3/Temp/nut-2.4.1/drivers/bcmxcp.c:224: undefined reference to `ldexp' /tmp/mnt/disc0_3/Temp/nut-2.4.1/drivers/bcmxcp.c:231: undefined reference to `ldexp' collect2: ld returned 1 exit status make[1]: *** [bcmxcp] Error 1 make[1]: Leaving directory `/tmp/mnt/disc0_3/Temp/nut-2.4.1/drivers' make: *** [all-recursive] Error 1
Как-то так. Чтобы узнать все возможные опции configure, запустите с --help.
Forum Guru
И, в случае кросс-компиляции, --host=mipsel-linux
Junior Member
Спасибо за советы, собрать драйвера я собрал, но вот работать они всё-равно не работают, в целом, ничего не изменилось:
Code:# megatec_usb -a Ippon -u root -DDDD Network UPS Tools - Megatec protocol driver 1.6 (2.4.1) Serial-over-USB transport layer 0.10 debug level is '4' Checking device (0000/0000) (002/001) - VendorID: 0000 - ProductID: 0000 - Manufacturer: Linux 2.4.20 ehci_hcd - Product: PCI device 14e4:471a - Serial Number: 00:03.1 - Bus: 002 Trying to match device Device does not match - skipping Checking device (0424/2502) (002/002) - VendorID: 0424 - ProductID: 2502 - Manufacturer: unknown - Product: unknown - Serial Number: unknown - Bus: 002 Trying to match device Device does not match - skipping Checking device (0665/5161) (002/003) - VendorID: 0665 - ProductID: 5161 - Manufacturer: Cypress Semiconductor - Product: USB to Serial - Serial Number: unknown - Bus: 002 Trying to match device Device matches DTR=1, RTS=0 Starting UPS detection process... Asking for UPS information [I]... I => FAILED [short read] I detail: (1 bytes) => 49 Asking for UPS status [Q1]... Q1 => FAILED [timeout] Asking for UPS status [Q1]... ser_send_pace: Device detached? (error -1: error sending control message: Broken pipe) ================================================== = device has been disconnected, try to reconnect = ================================================== Checking device (0000/0000) (002/001) - VendorID: 0000 - ProductID: 0000 - Manufacturer: Linux 2.4.20 ehci_hcd - Product: PCI device 14e4:471a - Serial Number: 00:03.1 - Bus: 002 Trying to match device Device does not match - skipping Checking device (0424/2502) (002/002) - VendorID: 0424 - ProductID: 2502 - Manufacturer: unknown - Product: unknown - Serial Number: unknown - Bus: 002 Trying to match device Device does not match - skipping Checking device (0665/5161) (002/003) - VendorID: 0665 - ProductID: 5161 - Manufacturer: Cypress Semiconductor - Product: USB to Serial - Serial Number: unknown - Bus: 002 Trying to match device Device matches Successfully reconnected Q1 => FAILED [timeout] Asking for UPS status [Q1]... Q1 => FAILED [timeout] Asking for UPS status [Q1]... Q1 => FAILED [timeout] Asking for UPS status [Q1]... Q1 => FAILED [timeout] 5 out of 5 detection attempts failed (minimum failures: 2). Megatec protocol UPS not detected. # dmesg | tail -n 20 usbdevfs: USBDEVFS_CONTROL failed dev 3 rqt 33 rq 9 len 8 ret -32 usbdevfs: usb_submit_urb returned -22 usbdevfs: usb_submit_urb returned -22 usbdevfs: usb_submit_urb returned -22 usbdevfs: usb_submit_urb returned -22 usbdevfs: usb_submit_urb returned -22 usbdevfs: usb_submit_urb returned -22 usbdevfs: usb_submit_urb returned -22 usbdevfs: usb_submit_urb returned -22 usbdevfs: usb_submit_urb returned -22 usbdevfs: usb_submit_urb returned -22 usbdevfs: usb_submit_urb returned -22 usbdevfs: usb_submit_urb returned -22 usbdevfs: usb_submit_urb returned -22 usbdevfs: USBDEVFS_CONTROL failed dev 3 rqt 33 rq 9 len 8 ret -32 usbdevfs: usb_submit_urb returned -22 usbdevfs: usb_submit_urb returned -22 usbdevfs: usb_submit_urb returned -22 usbdevfs: usb_submit_urb returned -22 usbdevfs: usb_submit_urb returned -22
Senior Member
Запустите с -DDDDD.
Senior Member
А megatec.c подправили? У меня с, работает нормально.Code:#define READ_PACE 10000 /* 300000 */ /* interval to wait between sending a command and reading the response (usec) */
Forum Guru
- С какой именно прошивкой экспериментируете?
- UPS через хаб подключаете или напрямую?
- usb 2.0 выключать пробовали (модуль ehci-hcd)?
Junior Member
Запустите с -DDDDD.Code:# megatec_usb -a Ippon -u root -DDDDDDDDDDDDDDDDDDDDDDDDD Network UPS Tools - Megatec protocol driver 1.6 (2.4.1) Serial-over-USB transport layer 0.10 debug level is '25' Checking device (0000/0000) (002/001) - VendorID: 0000 - ProductID: 0000 - Manufacturer: Linux 2.4.20 ehci_hcd - Product: PCI device 14e4:471a - Serial Number: 00:03.1 - Bus: 002 Trying to match device Device does not match - skipping Checking device (0424/2502) (002/002) - VendorID: 0424 - ProductID: 2502 - Manufacturer: unknown - Product: unknown - Serial Number: unknown - Bus: 002 Trying to match device Device does not match - skipping Checking device (0665/5161) (002/003) - VendorID: 0665 - ProductID: 5161 - Manufacturer: Cypress Semiconductor - Product: USB to Serial - Serial Number: unknown - Bus: 002 Trying to match device Device matches none (-22) DTR=1, RTS=0 Starting UPS detection process... Asking for UPS information [I]... none (-22) I => FAILED [short read] I detail: (1 bytes) => 49 Asking for UPS status [Q1]... none (-22) Q1 => FAILED [timeout] Asking for UPS status [Q1]... none (-22) none (-22) Q1 => FAILED [timeout] Asking for UPS status [Q1]... none (-22) none (-22) Q1 => FAILED [timeout] Asking for UPS status [Q1]... none (-22) none (-22) Q1 => FAILED [timeout] Asking for UPS status [Q1]... none (-22) ser_send_pace: Device detached? (error -1: error sending control message: Broken pipe) ================================================== = device has been disconnected, try to reconnect = ================================================== Checking device (0000/0000) (002/001) - VendorID: 0000 - ProductID: 0000 - Manufacturer: Linux 2.4.20 ehci_hcd - Product: PCI device 14e4:471a - Serial Number: 00:03.1 - Bus: 002 Trying to match device Device does not match - skipping Checking device (0424/2502) (002/002) - VendorID: 0424 - ProductID: 2502 - Manufacturer: unknown - Product: unknown - Serial Number: unknown - Bus: 002 Trying to match device Device does not match - skipping Checking device (0665/5161) (002/003) - VendorID: 0665 - ProductID: 5161 - Manufacturer: Cypress Semiconductor - Product: USB to Serial - Serial Number: unknown - Bus: 002 Trying to match device Device matches Successfully reconnected none (-22) Q1 => FAILED [timeout] 5 out of 5 detection attempts failed (minimum failures: 2). Megatec protocol UPS not detected.
А megatec.c подправили?Code:$ awk 'NR==71 {print $0}' megatec.c #define READ_PACE 100000 /* interval to wait between sending a command and reading the response (usec) */С какой именно прошивкой экспериментируете?Product ID: WL500gpv2
Firmware Version: 1.9.2.7
Firmware Release: 1.9.2.7-10
UPS через хаб подключаете или напрямую?Подключаю напрямую в нижний USB разъём, в верхний воткнут хард на 250 гигов.
usb 2.0 выключать пробовали (модуль ehci-hcd)?Только-что попробовал, если я выполняю # rmmod ehci-hcd, то у меня отрубается винчестер и я его примонтировать снова не могу, я даже не могу после этого выполнить команду # ls /dev, выдаёт что-то типа "Юзер сигнал 1".
Last edited by kvazimoda24; 11-06-2009 at 17:52.
Posting Permissions
Reply With Quote