Firmware v1.9.2.7 CR6, updated to CR6a ... now CR6b [Oleg]

[FauDrei]

(Where) can we read more about it Oleg?

[Oleg]

(Where) can we read more about it Oleg?

In the sources. The problem was that you got "no such device" in the log during the printing attempt, while the printer is detected and displayed on the status page.

[int]

int, it should work fine, as it mostly just a rebranded 6a.3, with except of printer fix

It seems that 6b work's very well..

I will test samba and printer tomorrow..

[int]

Its not possivel to include in AP Mode: Client mode ?


This are the best thing, in wl that are missing...


Lot of work???

[Oleg]

Its not possivel to include in AP Mode: Client mode ?


This are the best thing, in wl that are missing...


Lot of work???

It's already there: Wireless | Advanced | Extended mode > Ethernet Bridge.

[Tomekk]

Im now using 6b, and it seems quite stable... the auto negotiation in "wan connection speed" its working good (back again, finnally :P ).

I will continue to test after 72h of working and post my conclusions.

After some use of the 6a.3 ( ~72hours ) the firmware it seems stable and no resets, reboots or problems from services.

Once again just to remember my test's are using the WL500g with 1 connection in LAN and 3 WLAN connection WPA-PSK/ AES+TKIP ( 2 AES broadcom chip 802.11g and one 1 TKIP intel 802.11b ), with FTP server, DYNDNS and a print service port 9101.

[catdog]

catdog: try fix speed set to auto

Thank you Oleg for this fix, works fine now with the auto negotiation enabled.
You are a star!

[Tomekk]

My WL500g its been runing with a quite good stability more than 72H On and going up!
Thanks for developing this firmware since the begining

[Zitev]

Hi Oleg!

I use the new v1.9.2.7 CR6b firmware a few days. It's very stable, no restart, no slow down on auto negotiation mode, but the connection time is invalid in the future too.
"Jul 3 17:10:46 pppd[76]: Connect time 18673390.5 minutes."

Zitev

[int]

Hi

I can't make samba works on my WL500g...

I see other threats but its diferent on this FW...

I put my harddisk on WL, and i can see the files on /tmp/harddisk/


but what i have to do to make samba works fine with public read/write acess?

[Oleg]

Hi Oleg!

I use the new v1.9.2.7 CR6b firmware a few days. It's very stable, no restart, no slow down on auto negotiation mode, but the connection time is invalid in the future too.
"Jul 3 17:10:46 pppd[76]: Connect time 18673390.5 minutes."

Zitev

Hm... Have you read my answer?
http://wl500g.info/showpost.php?p=17766&postcount=63

[Oleg]

Hi

I can't make samba works on my WL500g...

I see other threats but its diferent on this FW...

I put my harddisk on WL, and i can see the files on /tmp/harddisk/


but what i have to do to make samba works fine with public read/write acess?

Have you assigned LAN Hostname to your router and enabled samba? Yes, samba is changed in the 1.9.2.7-6, but it's still works fine. For r/w access use share$

[int]

Have you assigned LAN Hostname to your router and enabled samba? Yes, samba is changed in the 1.9.2.7-6, but it's still works fine. For r/w access use share$

i already enable samba, and put LAN as my hostname, and don't work i see that smb.conf was not create...???

[Zitev]

[QUOTE=Oleg]Hm... Have you read my answer?

Ohhh...I missed your answer, sorry...THX!

Zitev

[Fama]

After changing from 1.9.2.7-6.3 to 1.9.2.7.6b after a few days without any problems, I am having disconnections again. Are there any differences between those 2 firmwares?
Please take a look at my logfile.

THX