Results 1 to 2 of 2

Thread: WL500g Premium not boot after flash firmware DD-WRT

  1. #1

    WL500g Premium not boot after flash firmware DD-WRT

    Excuse me but my english is very poor.

    i am a WL500g Premium router V1.14. i flashed with DD-WRT V24 VPN. This flash is OK, after, i flashed with DD-WRT V24 Mega. Flash is OK but after update parameters in interface web and after reboot, my router crash. Power LED is not blink but ON. If i used restore button, my router crash. Impossible ping 192.168.1.1. My IP address of computer is 192.168.1.2/255.255.255.0.

    I installed on serial port a chip MAX3232.

    A simple boot :

    CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
    Build Date: $T 12$¿ 14 15:54:18 CST 2005 (root@localhost.localdomain)
    Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.

    Initializing Arena
    Initializing Devices.
    et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 3.90.23.0
    rndis0: Broadcom USB RNDIS Network Adapter (P-t-P)
    CPU type 0x29006: 264MHz
    Total memory: 33554432 KBytes

    Total memory used by CFE: 0x80800000 - 0x8089B590 (636304)
    Initialized Data: 0x80831700 - 0x80833DE0 (9952)
    BSS Area: 0x80833DE0 - 0x80835590 (6064)
    Local Heap: 0x80835590 - 0x80899590 (409600)
    Stack Area: 0x80899590 - 0x8089B590 (8192)
    Text (code) segment: 0x80800000 - 0x80831700 (202496)
    Boot area (physical): 0x0089C000 - 0x008DC000
    Relocation Factor: I:00000000 - D:00000000

    Device eth0: hwaddr 00-xx-xx-xx-xx-xx, ipaddr 192.168.1.1, mask 255.255.255.0
    gateway not set, nameserver not set
    Null Rescue Flag.
    Reading :: TFTP Server.
    Failed.: Timeout occured
    Loader:raw Filesys:raw Dev:flash0.os File: Optionsnull)
    Loading:


    A boot with press Restore button :
    --------------------------------

    CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
    Build Date: T 12 14 15:54:18 CST 2005 (root@localhost.localdomain)
    Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.

    Initializing Arena
    Initializing Devices.
    et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 3.90.23.0
    rndis0: Broadcom USB RNDIS Network Adapter (P-t-P)
    CPU type 0x29006: 264MHz
    Total memory: 33554432 KBytes

    Total memory used by CFE: 0x80800000 - 0x8089B590 (636304)
    Initialized Data: 0x80831700 - 0x80833DE0 (9952)
    BSS Area: 0x80833DE0 - 0x80835590 (6064)
    Local Heap: 0x80835590 - 0x80899590 (409600)
    Stack Area: 0x80899590 - 0x8089B590 (8192)
    Text (code) segment: 0x80800000 - 0x80831700 (202496)
    Boot area (physical): 0x0089C000 - 0x008DC000
    Relocation Factor: I:00000000 - D:00000000

    Device eth0: hwaddr 00-xx-xx-xx-xx-xx, ipaddr 192.168.1.1, mask 255.255.255.0
    gateway not set, nameserver not set
    Null Rescue Flag.
    Hello!! Enter Rescue Mode: (by Force)

    Reading :: TFTP Server.
    Failed.: Timeout occured
    Reading :: TFTP Server.

    Ping 192.168.1.1 not response

  2. #2
    My router is Good. In fact, i used to ground pin 9 during 15 sec and not 3 sec

Similar Threads

  1. wl500gP v1 not booting after successfull flash of custom firmware
    By nocturne.op.15 in forum WL-500gP Firmware Discussion
    Replies: 6
    Last Post: 13-07-2008, 01:28
  2. Replies: 5
    Last Post: 13-01-2008, 23:50
  3. Firmware v1.7.5.6 CR5 [Oleg]
    By Oleg in forum WL-500g Firmware Releases
    Replies: 43
    Last Post: 14-07-2004, 21:54
  4. Total crash every day
    By Djuri in forum WL-500g Q&A
    Replies: 8
    Last Post: 09-06-2004, 09:05

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •