well, my unit worked perfectly, i wanted to setup an ddwrt in wl500g
with sp2 release
folowing instructions (first clearnvram,then restore and then ddwrt fw) i put clearnvram fw,and after that (i...
Type: Posts; User: xtraya
well, my unit worked perfectly, i wanted to setup an ddwrt in wl500g
with sp2 release
folowing instructions (first clearnvram,then restore and then ddwrt fw) i put clearnvram fw,and after that (i...
my asus goes 216 mhz
i bought it in may 2004, MAC adreses goes somthing like 00 0E A8 ...
those modules are mipsel compiled?
i will get an CM9 minpci card (i think that it best ATH a/b/g card on market)
and put into asus (on usb disc)
with that card, on PC linuxes i have an 7 km link...
and most important thing is to setup an darkstat database path (not to use /tmp/root folder). if you dont do this, after 5 minutes darkstat goes OFF...
my postbootscript is ..
#!/bin/sh
sleep...
with antiloop help ...
it works...
with flashfs,and ./darkstat & it works ok.... forget --detach command
i tryed much ways to setup darkstat from USB disk, but without succes because function ./darkstat --detach doesnt work on asus (on every other linux system it works perfectly)
how to fix it? ideas?
just imagine enormous disk usage,with milions of small files on a tiny 100mhz procesor.... bad thing is that squid is allmost 8 megabytes exe file... in whic part of ram can you put it? more bad...
is it possible to use zebra and ospfd from usb flash disc? just autoexec it after reboot?
well, how did i temporary solved this:
1. my asus have some problem and it automaticly restart itself in random order (without any rules when should it happen)
2. ofcourse i can manualy remove...
no, i want to use asus as router,but NOT to use default gw over WAN port (eth1)
just to use default gw over br0
i tryed to set nvram variables but, it won`t work because it set`s up ip of default gw but for wan interface.
routing table
0.0.0.0 10.15.1.10 0.0.0.0 UG 0 0 ...
SNMP is great feature, especialy for monitoring purposes
There are 2 important things:
1.OID is a number with dot`s. someting like 1.3.6.1.2.1.2.2.1.16.5
every oid is a mark for some SNMP...
ok, I will reset it, but still shaping doesnt work ok.
i tryed on other asus wich i have, it still gives a message in router log
(few same messages with changed number of class)
HTB: quantum...
well,my asus remembered in nvram old setings of shaper, and now anyone value which i set up in web interface,it wont work....
it simply loads older settings....but in a web are new ones
can...
yes,i forgot to say that linksys is not like asus, it has 3 mac adresses, very similar one to another, diference is in last digit
every interface has unique mac, ethernet,wlan,and wan
1. setup asus in wds-ap mode
2. setup bridge in HYBRID mode
3. add mac adress of linksys unit
4. reboot
(note that all units wil be on a same subnet)
5. put alchemy firmware in linksys
6....
use wds mode, i use linksyses and AP 500g , with 4-5 wds connections and it works perfect....
and alchemy of course on linksyses, or if you want client mode , must use samdahi 2.00 on linksys...
but now, what can i do to reactivate unit?
well, everything worked so fine, on firmware 1.7.5.9 cr2
i just uploaded new one,then done button reset...
router is now in AP mode, SSID "Broadcom" , on 192.168.1.1 but wont accept any...
[admin@ap2-3-BB root]$ wl txpwr1
TxPower is 77 qdbm, 19.25 dbm, 84 mW Override is On
[admin@ap2-3-BB root]$ wl txpwr1 100
[admin@ap2-3-BB root]$ wl txpwr1
TxPower is 144 qdbm, 36.00 dbm, 255...
500g with marwell chipset works fine, but problem is in asus 138g card, because it is less sensible, and you must have very good antenna to have performance on a picture below (2,7 Mb/s)
...
Problem:
Everything worked so fine, 2.2 Mb transfer in both directions.
Suddenly i rebooted AP unit, and after that I could not connect again
I tryed everything to change but without succes,...
Sensitivity, of course is more important factor than a power of chipset. If your card (unit) have good sensitivity (prism 2.5), signal of -80 dBi gives a full performanse (-90 dBi is minimum useful...
Of course, you know for linsksys hack, and power boost for more than 200 mW
My friend tryed this with alchemy fw on linksys wrtg54g, and it works but after few days, unit becomes allmost dead with...
I have luck because i uploaded firmware, and forgoted to turn off proxy server in my wifi network
and firmware traveled 6 times over wireles :), but everything was ok...