Search:

Type: Posts; User: lukie

Search: Search took 0.01 seconds.

  1. Thread: Block IP

    by lukie
    Replies
    4
    Views
    4,519

    Thanks for your helpful instruction barsju. It...

    Thanks for your helpful instruction barsju. It almost worked in my case.
    The for-loop didn't work properly. This worked well:


    #!/bin/sh
    for ip in $(cat /usr/local/etc/block.ip)
    do
    iptables...
  2. Replies
    19
    Views
    49,930

    How to display ports of connected PCs?

    Hi there!

    Is it possible, to show which ports are being used by PCs connected to the router? Something like a local 'neststat' output. Should display wired and wlan PCs.
    Can i use the netstat...
  3. Very strange. I still can't upgrade to 1.9.2.7...

    Very strange. I still can't upgrade to 1.9.2.7 official, but i could upgrade to OLEGs 1.9.2.7-7b. Hooray! And my printer HP LJ 1100 still works.
    Respect! Did you change something special, Oleg? Or...
  4. I have exectued the command, then plugged off...

    I have exectued the command, then plugged off power, hold restore and flashed the firmware: Problem still exists.
    I also exectued the command, exit telnet and ipgraded with web-interface. :(

    I...
  5. I have to say that i know almost nothing about...

    I have to say that i know almost nothing about linux and the internals of the router. :(

    I used your 1.6.5.3 custom Firmware to be able to get a telnet connection. After searching this forum I...
  6. @Antiloop This is what i called upgrade in...

    @Antiloop
    This is what i called upgrade in 'manual recovery mode' with the utility. Does not work too.

    @all
    There is one thing i didnt notice yet: After successful upload and "preparation" of...
  7. Thread: USB-FTP Server

    by lukie
    Replies
    29
    Views
    40,300

    Perhaps these two folders have to be created...

    Perhaps these two folders have to be created manually on the USB drive:

    ftp_pub
    ftp_pvt
  8. @wiz Yes, unusual. After hitting F5 for...

    @wiz
    Yes, unusual. After hitting F5 for 9minutes, waiting for the web-page to appear, i gave up.

    Here are the results:

    usual status with 1.7.5.6

    total: used: free: shared:...
  9. Thank you all for your help. :) But it still...

    Thank you all for your help. :)
    But it still doesn't want to upgrade.

    The flasher says the upgrade was successful. But after doing a reset via the 'restore' button, the Powerled flashes slowly...
  10. After the upgade i pushed the the restore button...

    After the upgade i pushed the the restore button on the back as it was said.
    After this the PowerLED started blinking, i had still no web access and the router was instantly in 'restore mode'.
    ...
  11. Firmware update problem (from ~1.8.1.7 to 1.9.2.7)

    Hi There!

    I want to upgrade to FW 1.9.2.7 because of its 'bandwidth management' capabilities i need. I can't upgrade. After uploading of the firmware i waited 5min. Tranfer successful, PLED was...
  12. Thread: [LPT] Printers

    by lukie
    Replies
    77
    Views
    162,787

    Tested: WORKING! Model: WL-500g Firmware:...

    Tested: WORKING!
    Model: WL-500g
    Firmware: 1.7.5.6

    Device
    Brandname: HP (Hewlett Packard)
    Brandtype: LaserJet 1100
    URL To manufacturer: http://www.hp.com
    URL To product: HP Laserjet 1100
  13. Replies
    20
    Views
    11,729

    This helped my with my HP Laserjet 1100 which is...

    This helped my with my HP Laserjet 1100 which is connected by the LPT Port.
    Follow the instructions given in the Manual.
    Open the properities of your connection: 'Standard TCP/IP Port'
    Select the...
Results 1 to 13 of 13