echo -e "From: test@test.com\nSubject: this is the subject\nReply-to: reply@server.com\nHere goes the mail body" | mini_sendmail -fnotused@ -ssmtp.server.com recipient@testide.com where -e option...
Type: Posts; User: sodb
echo -e "From: test@test.com\nSubject: this is the subject\nReply-to: reply@server.com\nHere goes the mail body" | mini_sendmail -fnotused@ -ssmtp.server.com recipient@testide.com where -e option...
Have you tried to set the wl500g in Access Point mode under System Setup --> Operation mode menu? This links together wlan + 4 Lan + WAN port into a single bridge.
add
src bcan http://bcan.burngreave.net/bcanopenwrt/packages to your ipkg.conf file and run ipkg update and install with ipkg install libstdc++. I used it to install iperf. Must admit, I installed...
You can use ncftpput for command line driven ftp client. See rrd_iptables.tar.tgz file in the attachement of post graphical ip accounting
Can you post your newly compiled drivers (usbserial.o and ftdi_sio.o)? I have a ftdi module that won't work, maybe the new drivers also solve my problems.
When using the setserial command as suggested earlier in this thread (patrik) you can use both ports simultaneously without a problem. Only with default compile options, the port 0 is used as a...
Are you shure about the correct COM port. It seems that you hyperterminal to the internal modem instead of the USB/COM port. A USB/serial convertor usually does not respond at AT commands.
I connected an old Palm IIIx (approx $25 on 2nd hand shop) through a serial port to the wl500gx, either using a usb to serial connector or the second internal serial port. Advantage is that you can...
Had the same problem. Problem can be solved by putting iptables initialization script (add_iptables.sh) to the post-firewall script in /usr/local/sbin and activating with flashfs save / flashfs...
use iptables -n option to switch off DNS resolving
Yes, how obvious...:o... it works. Initially I put the rules in the post-boot script. Because I use rrdtools to log traffic, a reset of the iptable counter is only a 5 minute loss of data.
I experience similar problems,e.g. iptables rules disappear without a reset of the router. I can not figure out what the disapperaing triggers. I am using pptp from my router to ADSL modem (ppp0 WAN...
You could add the IP addresses 7-16 in the ipaddress.txt file. Altough you don't know who is connected, the traffic gets sorted to the specific IP addresses. You need individual entries in iptable to...
Hello WiziPok,
I don't quite understand what you mean by non registered IP traffic. I suppose you mean all traffic from and towards IP addresses in your LAN that are not fixed addresses or served...
Probably the same as KAMILEK produced, here are my scripts.
Using the older scripts of my earlier html-based graphical IP accounting, together with the improvements Mark Koops made, and with the...
I use the firmware crond and crontab. In de post-mount/post-boot script I enter mkdir -f /var/spool/cron/crontabs. Copy the cron file (e.g. admin) to the /var/spool/cron/crontabs directory and start...
That's good news. Can you please post the binary of the setserial util? I will try without the CONFIG_SERIAL_SHARE_IRQ flag first.
I tried to install these packages. Everything works fine, except the libpng or other graphical libraries are not included. Any feature leading to real graphics causes a 'segmentation fault'....
Just remove the following lines from add_iptables.sh, because they are not used:
# ipnumbers of PC's in LAN
ipnumbers=`cat $accountdir/ipaddress.txt| $AWK '{print $2 }'`
Have you installed the...
When serial ports share same interrupt, do we need to explicitly enable
CONFIG_SERIAL_SHARE_IRQ Or is that done automatically. What about IRQ 1,5 and 6. I do not see them in /proc/interrupts? Could...
On two sessions I started cat /dev/tts/0 and cat /dev/tts/1 respectively. Because I only have a single serial port on my laptop I can only test alternatevely. That works.
Then I did a test where I ...
Hey, thanks Oleg,
i just typed
/tmp/harddisk/busybox stty -crtscts < /dev/tts/1 and now I can input and output to /dev/tts/1. However, after disabling the console I actually did not try the...
see Thread 1993 on disabling console on /dev/ttyS0. Would it cost you guys a lot of effort to discuss this topic in English, because I am certainly interested in getting both serials work...
I am not so fluent in Russian, but the intriging title of this thread contained ttyS0 and in the posts I could see ttyS1 and IRQ and WL500deluxe. Therefore, could one of the contributers in this...
I recompiled kernel with the following change in kernel.config
CONFIG_CMDLINE="root=/dev/mtdblock2 noinitrd init=/linuxrc console=null"
Now the console is disabled and is free to use for own...