Search:

I will try find a chance to test them out this weekend.

The stability issues that seemed to have been introduced turned out to be a dodgy USB cable. Since i have swapped that the connection is...

Sorry about that, it was done in a bit of a rush. When i did the patching i did look through the kernel patches, but it looked as if all the patches in koppel against 2.4.20 are already applied in...

I've started a new thread with a link to the source tree as a bzipped tarball.

http://wl500g.info/showthread.php?p=168930#post168930

Hi Guys,

As some of you may have seen i had a go at merging the Koppel USB wireless broadband mods into Oleg fw found on wl500g.googlecode.com.

I provided a link to a trx for the WL500GpV2 in...

Quite happy to do this, but again will have to wait till I have access to a net connection that doesn't limit my down/upload, so prob when i'm next at my parents (next weekend most probably)

I was getting frustrated with having two different firmwares that each were good in their own respect but didn't do all that i wanted in one. So I have taken the koppel patches and put into the...

Thanks!

just checking out the src so i can build that as want to make some customisations.

Ah, i suspect i shall have to have look into hacking the kernel myself, as My router being a wl500gP V2 is only supported from 1.9.2.7-10.

Hi guys,

thanks for yr input,

No USB hub, this happens when I have 1 device attached.

I will look for and try the 7-D version

I thought the 2.4.20 kernel was very old!

Hi,

I've just flashed my WL500gP V2 with Olegs -10 version and have a problem with USB devices. Plugging in a USB flash drive works fine however both my mobile phone and a USB audio dongle (cheap...

Hi Oleg,
I have downloaded and patched the Asus 1.9.2.7 to yr 7g revision.
The make and make image-wl550g complete without error, however the resulting .trx file is 2.7MiB vs yr built image of...

Has any body considered adding a USB2 host controller too there wl500g?

I would think all the required signal are exposed on the Mini PCI conector.

I'm used to soldering tiny legs on tiny...

Got distracted by the TV, but I found the fix to be surprisingly easy, simply change th kernel boot params to say console=ttyS1 instead of console=ttyS0, this removes the kernel output and the shell...

Hi, my laptop is less fussy about baud rate and reveals i do indeed have a fully functioning shell on tts/0. I have found what appears to be where the shell is set up in init.c, im going to try...

Hmm!

I rebuilt my firmware and flashed with the console=/dev/tts/0 omitted and confirmed it updated by checking dmesg

zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command...

Hallo there,

I've built a dinky little thing, with a BFP48 packaged TL16C550CPTG4
datasheet http://www.farnell.com/datasheets/61904.pdf

It sends chars fine, as the WL500g responds to commands...

Forgot to mention.. on the hardrives side.. you could in theory add many, assuming u have USB hubs to chain together.. But bare u mind they will all be sharing bandwidth of a single USB connection...

Hi,

These devices have limited RAM and processing power and as such you certainly don't want to be trying to run any kind of GUI based application on them.

The fact you mentioned VNC seems to...

Hi again, i edited my last post and wrote a load more, be time i had submitted it you had already replied to the original! Sorry, i realised that was a bit of a poor reply hence my editing it!

Hmm, in my edit i deleted the original reply.
waveserver is approximately 90k
my oss_server app is 12k.

Thanks, that gets some of the way, It seems to effectively replace the file, but not...

Hi,
I know many think its a useless feature, but i find it very useful and tidy way to get audio to my kitchen without cables.

As suplied by Asus this only works with WMP, which along with...

Hi there,

Yes you should be able to use a microphone input. The USB audio dongle i have has both mic in and speaker out. I do not use the mic in so cannot confirm for certain that it works, but i...

Hi, I have written my own version of waveserver, which currently just accepts raw data and pipes to the sound device via oss.

I wish to automate the starting of this, and replace the loading of...

Oh, yes i did, i have no need for ftp! i had a quick look but couldn't find any scripts related to this stuff.

Wanted to check what was done when, so i can for example make it mount the drive...

Wheni I first plugged a usb storage device into my wl500g, the required modules were loaded and the filesystem was mounted on /tmp/harddisk.

However it now does not. dmesg reports a device was...