View Full Version : How to wireless bridge my 2 networks?
Lord_Moebius
09-09-2004, 22:00
Hi!
My current network consists of a WL500g "X" connected to ADSL and a few systems hooked up using UTP.
X is using Oleg's modded 1.7.5.6 and is in "gateway" operation mode (Sytem Setup) with extended mode "access point" (Wireless->Interface).
My wife has a separate laptop and uses WiFi to connect to the WL500g, but too often she seems to suffer from poor signal.
So I just bought a second WL500g "Y" with the idea to put it somewhere in between X and my wife's favorite working spots and boost her signal.
I want Y to function as a wireless bridge (WDS?) but also want to be able to connect devices using UTP and possibly a webcam and a printer.
I flashed it with the newest firmware 1.8.1.9.
I can't seem to get it to work though... :mad:
I tried putting Y in Access Point mode (System Setup) and Hybrid (Wireless->Bridge), with the MAC address of X in the Remote Bridge List, and setting both X and Y on the same channel, but alas... Y just can't seemed to connect to X even though WEP keys and Access Control are set correctly.
I also tried putting Y's Operation Mode on "ether bridge" (Wireless->Interface), putting both X and Y in hybrid mode, but without success.
When in "ether bridge" mode, Y's System Log states "Connecting to <SSID>" but never seems to get there.
As a nasty extra, whenever Y is activated, my wife's laptop seems to loose its IP-configuration and getting bogus instead.
How can I set this up correctly? I think it's a text book case, but the Asus docs are not really helping me here.
What settings do I need to configure on X and Y to get this working?
Thank you so much!
Erwin
geethreeforce
15-09-2004, 18:30
Hi,
My collegue had the same problem creating wireless bridge.
He solved the problem by running the latest asus firmware 1.8.1.9 on both his WL500G boxes. With the CR builds he also couldn't get this to work.
Hope this helps.
Although you have to give up the CR release with it's lovely extra functions.
I dont know if there are plans for a CR release based on 1.8.1.9
Maybe Oleg or Antiloop can shine some lite on that matter.
Regards Niels
Antiloop
15-09-2004, 19:54
try using the same custom firmware at your WL500g (Y) if you haven't tried yet..
i can also suggest you to probably solve the problem with using a broadcom based wireless card if you aren't using one yet
Although you have to give up the CR release with it's lovely extra functions.
I dont know if there are plans for a CR release based on 1.8.1.9
Well, I've started porting things to 1.8, but it's now halted due to the lack of time... Volunteers with linux knowledge needed to help me porting all the stuff we've in the 1.7.5.9.
In fact, once custom firmware will be ported to 1.8, we will have ~400k of free space in the flash, so we will be able to add more features, this is the only reason for migration.
Same problem with coverage in my house, so:
I'm using 1.6.5.3 on both wl-500g, and it works! Both are set to "hybrid" - same channel, X is "home gateway" and Y is "access point". Using WEP-64.
BUT, my second PC using wl-138g has problems, the wireless keeps loosing connection with Y, this is really a pain. :mad:
I do have a satellite tuner with cable-network-connection to "Y" and there is no problem with this.
To make sure the second PC only connects to Y, I have omitted its MAC in X access control.
All PC using same subnet, and the same 192.168.1.x-series.
Same problem with coverage in my house, so:
I'm using 1.6.5.3 on both wl-500g, and it works! Both are set to "hybrid" - same channel, X is "home gateway" and Y is "access point". Using WEP-64.
BUT, my second PC using wl-138g has problems, the wireless keeps loosing connection with Y, this is really a pain. :mad:
I do have a satellite tuner with cable-network-connection to "Y" and there is no problem with this.
To make sure the second PC only connects to Y, I have omitted its MAC in X access control.
All PC using same subnet, and the same 192.168.1.x-series.
And voila, did uncheck the "activate IEEE802.x ....." in advanced setting, and now everything is working flawless!!!!!!!
BUT, using WEP-64, want to use WPA...which might be a challenge later.
Same problem with connecting as Lord Mobius but in my case, “X” is an AP in a big W WAN (Symbol tech.) so I can’t fix it with firmware. I have installed 1.8.1.9 on Y.
Setting up my WL-500g (Y) as: Home gateway (want to share IP-address for my 3 PC’s (wired to WL-500g, no wireless)), WDS only, bridge mode, fixed IP on WAN, default on LAN with DHCP. No NAT-settings, no Internet firewall settings, Also want to share printer from WAN and LAN side, share a ftp-server on internet.
Result: Connecting to AP is OK, but 0.0.0.0 is showing as IP-address in the WAN (I have access to the switch). In wl-500g web home page everything looks OK. :mad:
Next step: changing IP and subnetmask on LAN-side to the WAN IP and subnetmask 255.255.255.192
Result: IP showing on WAN seems OK but no connection to internet (gateway IP ?). Web home page have now changed WAN IP-address and subnetmask. Can ping wl-500g from LAN or from WAN but not through. If I connect to web page from WAN-side, WAN IP and subnetmask is different from web page from LAN. :mad:
Next step: Entering WAN gateway IP as gateway IP on LAN (still impossible to enter the right IP on WAN, wl-500g change it to 1.1.1.1 and subnetmask 255.0.0.0)
Result: web page have changed WAN /default gateway IP,
wl-500g is acting on WAN with the gateway IP as it’s IP-address= KAOS. :eek: :eek: :eek:
During this tests I must have caused a lot of wrong traffic, because our ISP have shot down the Gateway 3 times now as a result of my trials. Meaning I’m now not willing to test “in the dark” anymore.
I have also tested different settings ( AP-mode, hybrid – AP, …… ) always with some of the results mentioned above.
Now, what to do ? Sell my wl-550g cheap to someone with more (or less) knowledge and buy 5 adapters/bridges ?
Or have information from someone here on this forum ! :o
Well
The commercials about wl-500g was talking about a great HW.
But it looks like it was a bit overrated.
More just a toy for connecting to other ASUS stuff. Not according to open standard, 802.11... .
So far no help or solutions from neither ASUS or this forum.
So the conclusion is:
I will sell my wl-500g (cheap) and not recommend it to others.
Same problem with connecting as Lord Mobius but in my case, “X” is an AP in a big W WAN (Symbol tech.) so I can’t fix it with firmware. I have installed 1.8.1.9 on Y.
Setting up my WL-500g (Y) as: Home gateway (want to share IP-address for my 3 PC’s (wired to WL-500g, no wireless)), WDS only, bridge mode, fixed IP on WAN, default on LAN with DHCP. No NAT-settings, no Internet firewall settings, Also want to share printer from WAN and LAN side, share a ftp-server on internet.
Result: Connecting to AP is OK, but 0.0.0.0 is showing as IP-address in the WAN (I have access to the switch). In wl-500g web home page everything looks OK. :mad:
Next step: changing IP and subnetmask on LAN-side to the WAN IP and subnetmask 255.255.255.192
Result: IP showing on WAN seems OK but no connection to internet (gateway IP ?). Web home page have now changed WAN IP-address and subnetmask. Can ping wl-500g from LAN or from WAN but not through. If I connect to web page from WAN-side, WAN IP and subnetmask is different from web page from LAN. :mad:
Next step: Entering WAN gateway IP as gateway IP on LAN (still impossible to enter the right IP on WAN, wl-500g change it to 1.1.1.1 and subnetmask 255.0.0.0)
Result: web page have changed WAN /default gateway IP,
wl-500g is acting on WAN with the gateway IP as it’s IP-address= KAOS. :eek: :eek: :eek:
During this tests I must have caused a lot of wrong traffic, because our ISP have shot down the Gateway 3 times now as a result of my trials. Meaning I’m now not willing to test “in the dark” anymore.
I have also tested different settings ( AP-mode, hybrid – AP, …… ) always with some of the results mentioned above.
Now, what to do ? Sell my wl-550g cheap to someone with more (or less) knowledge and buy 5 adapters/bridges ?
Or have information from someone here on this forum ! :o
If you want some sensible answers you may wish to start with a proper description of you LAN setup.
Is the wl500g connected directly to your WAN (modem)? If so what is the gateway adress of your modem? Do you have an active DHCP server on your modem? If yes, what are the settings?
I really don't understand what you are doing with the IP adresses and subnetmasks and gateway
If your modem is connected directly to the wl500g you may wish to try Automatic IP for your WAN (That is if the modem has an active DHCP server)
What is the IP adress range / gateway of your WAN
What do you mean by sharing an IP adress for 3 PC's
Any firewalls active by chance
Don't give up so soon!!
Simple set up but strange effects when configuring.
As described I want my wl-500g to be wireless connected to an AP (Symbol) in a big (wireless) WAN = No modem. In the WAN we all have fixed IP-addresses.
Hoped to use the wl-500g with at least 1 PC (or 3) and network printer and ftp-server connected by wire to it. All with just one IP-adress on WAN and Internet. Latest firmware installed.
But setting up wl-500g (= se my first post) just resulting in these examples:
1. sending it's IP-address to the AP as 0.0.0.0 or
2. 192.168.1.1 (=LAN-IP) (if I changed to station mode)
SO I changed the LAN-IP-address to value of WAN-IP and now it's showing right IP-address on WAN-side. Ping OK from WAN, not from Internet or LAN (Gateway-value missing or wrong? + .... on LAN-side?).
SO testing with just changing to ethernet bridge mode => now the Gateway-value is seen as IP-address for the wl-500 on the WAN = kaos on the WAN
=> ISP shuting down the gateway for the whole WAN.......
So, best result so far (tested a lot of alternatives) is "Home gateway", "WDS only" and "station mode". Then I can at least ping from WAN, but not from Internet or LAN. Same with printing.
How to get it working from Internet and LAN ?
I concur with Brubber. The reason why you haven't got any answer here is because its difficult to understand what your (planned) network setup is and where the problems are. I've read your posts three times and I still haven't got a clue to what you want. So I can't respond to your question, and uless I'm really simple, so will most other forum menbers.
The Asus router is indeed not without problems (never believe marketing talk for that matter), but it certainly has lots of advantages over the other gray products which crowd the market. Look at it as a raw diamond, it just needs crafted handling and a beautiful jewel will emerge. :D
Try to elaborate more and post a picture (scheme) here of your setup. Then we'll see what we can do to help...
Antiloop
03-10-2004, 16:50
hmm make a clear visio drawing and attach it to your post
This is my wanted setup.
So, how should this be accomplished ?
chipanzee
04-10-2004, 18:42
Basically, you just exchange WAN with WIRELESS. But I believe there is a few things that you need to change :
bridge
The default configure bridge WIRELESS and LAN. You may need to break this or all your LAN port may be opened to the world, though I read somewhere that wireless bridge this way may not work at all.
firewall/SNAT
You would need to change the firewall rules so it blocks things from WIRELESS instead from WAN and SNAT on outgoing through WIRELESS instead of WAN.
put WIRELESS in client mode
So your WIRELESS interface act the same as the "notebook" in the diagram.
That should be it. Don't ask me how though as I am using openwrt and not the ASUS firmware but they should be pretty similiar in terms of setup.
Your thoughts are about the same as mine when I started.
Now I don't know
Bridge: I set "WDS only" in bridge settings. Open ports?
Well, when making a port scanning the only port reply I get is from 21-ftp, 80-www, 515-printer and sometimes 5431-ParkAgent (?) and that is from both LAN-side and WAN/wireless side. Different firewall or NAT-setting don't change that.
Wireless in Client mode:
Well, that option is not on the standard meny. That is also what ASUS Tech support Center answered "WL-500g can not be a wireless client".
And I've tested Olegs 1.7.5.9 and setting: nvram set 13_x_ClientMode=2 ....
No luck. Sure it's working ?
Looking into this forum, openwrt seems to demand some deeper knowledge in programming or codes. I don't have that.
This is my wanted setup.
So, how should this be accomplished ?
Very nice and clear picture, however for me still a lot of info missing. Even though it appears to me that you have more then adequate knowledge of TCP/IP it still possible you are overlooking something obvious.
Is there a DHCP server active (on your switch / ap)
Sure the IP adress you assign to to your asus "..185" is free?
for WDS do you use anonymous option or Bridge list?
If bridge list, sure you typed the MAC adress correct
Perhaps you need to define static route(s) to get the thing working
Sure the switch / AP setup is correct? (What kind of rights do you have on the switch / AP?)
Routing table(s)?
Tried a trace route?
Why use DHCP on the asus? Your scheme suggests you only connect desktops and printer
Setting up my WL-500g (Y) as: Home gateway (want to share IP-address for my 3 PC’s (wired to WL-500g, no wireless)), WDS only, bridge mode, fixed IP on WAN, default on LAN with DHCP. No NAT-settings, no Internet firewall settings, Also want to share printer from WAN and LAN side, share a ftp-server on internet.
Result: Connecting to AP is OK, but 0.0.0.0 is showing as IP-address in the WAN (I have access to the switch). In wl-500g web home page everything looks OK.
Seems to me this is the way to go. Perhaps you should still define static routes.
What do you mean with "looks OK" (What do the relevant status windows report?)
P.S.
For those who don't know, 0.0.0.0 designates a default gateway. This is used in routing tables to represent "All Other Network Addresses".
To me it seems you need to switch the switch/AP and the Asus router. Configure the WL500g as router/gateway with a DHCP client on WAN side and a DHCP server on LAN/wireless side.
Hopefully I've missed something
No DHCP server on switch/AP. And no other limitations except WEP.
Yes, ... 185 is free. No other is using it ( I have administration rights to W WAN and switch)
Bridge: tested both, mostly use MAC-list and MAC-address is OK
(I have connection and authentication with the switch/AP from time to time, not always)
I've also set up a special WLAN in the switch with a route to the gateway, no effect.
Set up a route in wl-500g to gateway, no luck.
Trace route: from LAN-side just 1 hop to the WAN IP. from WAN nothing.
DHCP on LAN ? Well, no special reason.
web page "Looks OK". Well, I don't trust what is showing on neither web page or status page with the ASUS firmware. They show different values on IP-addresses and can change value if I just change some setting with let say bridge or AP or ....
So now I moved over to Igors 1.7.9-5. At least it is consistent in behavior
The routing table say:
192.168.1.0 0.0.0.0.0 255.255.255.0 U br0
0.0.0.0 xxx.xxx.xxx.129 0.0.0.0 UG eth2
xxx.xxx.xxx.128 0.0.0.0 255.255.255.192 U eth2
And the last row is a puzzle. Why .... 128.
It's there whatever I set different values.
And if I read all NVRAM values no ....128.
Styno, what You suggess is:
Treat the switch/AP as a wireless client in a wl-500g router/gateway configuration ? Right ?
Interesting idea or is that what Igor ond others have been talking about in different treads ? Not clear what they ment.
I've tried with that ( Op- mode:AP, bridge Hybrid, and manually assign IP-addresses (=my static public IP-address) on W LAN
.No more luck with this than the other.
At the moment there has been a long time when 0.0.0.0 is showing in the switch, but I can see that there is a connection, authentication and some traffic in both ways. But suddenly it can change so I can ping from WAN, but never from Internet. When, how and why I haven't figured out yet.
OK, long answer but many questions.
Just a new comment about routing table:
I tested with some different setting for static route + Apply and not.
Now the line with ...... 128 is gone, but I now have
82.0.0.0 0.0.0.0 255.0.0.0 U eth2
I can change static route or disable it or ..., line in table is unchanged.
And no change in switch.
Hopefully I've missed something
192.168.1.0 0.0.0.0.0 255.255.255.0 U br0
0.0.0.0 xxx.xxx.xxx.129 0.0.0.0 UG eth2
xxx.xxx.xxx.128 0.0.0.0 255.255.255.192 U eth2
And the last row is a puzzle. Why .... 128.
It's there whatever I set different values.
And if I read all NVRAM values no ....128.
xxx.xxx.xxx.128 is there because it's your network IP, that is if you use netmask 255.255.255.192. Reading some basic stuff concerning IP / routing etc. may be good idea, and will perhaps even solve your problem
0.0.0.0 xxx.xxx.xxx.129 0.0.0.0 UG eth2, this is the way to the outside world (WAN). So what is eth2?? I guess this is the wireless connection to your switch?
My routing table looks very similar, I only have an extra line defining multicast boundary on my LAN conn.
If I inderstand you correctly you are able to reach your WAN from the Asus, so i guess you can also reach the internet
Getting to your router from the internet is a different issue which was/ is discussed in a number of topics on this forum
Yes, what I mean is: Connect the WL-500g directly to the internet. Configure it as gateway using the 'System Setup - Operation Mode' menu. Configure a DHCP server for LAN and WAN. The rest should be piece of cake (Or I'm thinking too simple here :rolleyes: )
Antiloop
06-10-2004, 23:58
@brubber
when quering an Ripe address you should also use the ripe server
this is the real output:
% This is the RIPE Whois secondary server.
% The objects are in RPSL format.
%
% Rights restricted by copyright.
% See http://www.ripe.net/db/copyright.html
inetnum: 82.0.0.0 - 82.0.3.255
netname: CYBERWARE-LTD
descr: Cyberware Ltd
country: GB
admin-c: FO126-RIPE
tech-c: NNMC1-RIPE
status: ASSIGNED PA
mnt-by: AS5089-MNT
changed: hostmaster@ntli.net 20030630
source: RIPE
route: 82.0.0.0/14
descr: NTL-UK-IP-BLOCK
origin: AS5089
mnt-by: AS5089-MNT
changed: hostmaster@ntli.net 20040929
source: RIPE
role: NTLI Network Management Centre
address: NTL Internet
address: Crawley Court
address: Winchester
address: Hampshire
address: SO21 2QA
trouble: -------------------------------------------------------
trouble: For abuse notifications please -
trouble: file an online case @ http://www.ntlworld.com/netreport
trouble: +44 1633 710142 (Voicemail Only)
trouble: -------------------------------------------------------
trouble: For peering issues/requests please -
trouble: email : peering@ntli.net
trouble: -------------------------------------------------------
admin-c: MH22007-RIPE
admin-c: CF2297-RIPE
admin-c: CM1377-RIPE
tech-c: MH22007-RIPE
tech-c: CF2297-RIPE
tech-c: CM1377-RIPE
nic-hdl: NNMC1-RIPE
mnt-by: AS5089-MNT
notify: data.planning@ntl.com
e-mail: data.planning@ntl.com
changed: hostmaster@ntli.net 20030328
changed: hostmaster@ntli.net 20030401
changed: hostmaster@ntli.net 20030603
changed: hostmaster@ntli.net 20030707
changed: hostmaster@ntli.net 20040303
changed: hostmaster@ntli.net 20040312
changed: hostmaster@ntli.net 20040929
source: RIPE
person: Frank Oakes
address: Litton House
address: Global Business Park , Saville Road Westwood
address: Peterborough
address: PE3 7PR
phone: +44 1733765050
nic-hdl: FO126-RIPE
changed: hostmaster@ntli.net 20021104
source: RIPE
@brubber
when quering an Ripe address you should also use the ripe server
this is the real output:
You're right, removed my post. The idea was only to show that the 82/8 range was allocated to RIPE who then ofcourse assign specific ranges
Yes Styno, I think that is too simple. Shouldn't be, but ....
That was my 1st, 10th, 20th, 50th, 100th and ...th attempt
From Ripe and WhoIs is a confirmation about IP-address (and right owner ....)
REach WAN from ASUS:
No, when trying to ping from LAN-side I can only ping ASUS LAN and WAN IP.
Not even the switch or anything else, internet or not.
Trying to ping wl-500g from WAN-side is more problematic.
Since most of the time 0.0.0.0 is the identity wl-500g gets in the switch, I can't ping wl-500g even from the WAN.
WHEN I have the right identity in the switch I can ping wl-500g WAN-IP from a PC in the WAN.
When, why and how I can or can't get the right IP identity in the switch I haven't figured out yet.
It can suddenly change without any action from me, it can change when I pull out the power and restart wl-500g. But it's hard/impossible to repeat it.
And when I have contact and then make changes or just reboot I may or may not lose contact or it turn to 0.0.0.0 again.
I am more and more sure that it's a compatibility problem.
But don't lose the hope as someone said earliar in the tread. "The diamond is there". Where ?
Since most of the time 0.0.0.0 is the identity wl-500g gets in the switch
Please correct me if I'm wrong but I still think this is because for the switch / AP the asus is the default gateway for the Asus LAN
In your switch routing table there should then be some entry like:
0.0.0.0 192.168.1.1 0.0.0.0 UG brx (G for Gateway)
Also still wondering what eth2 is doing in this line:
0.0.0.0 xxx.xxx.xxx.129 0.0.0.0 UG eth2
Did you try the following setup:
Asus in AP mode (System setup; Operation mode)
Authentication mode "Open System or Shared Key" to start with (Wireless; Interface)
Block Broadcast SSID "No" (Wireless; Interface) SSID take from switch (Case sensitive??)
AP mode "WDS" Or "Hybrid"; Connect to AP's in Remote Bridge List "Yes"; Allow Anonymous "Yes" (Wireless; Bridge)
Add MAC adress of your switch to Remote Bridge List (Wireless; Bridge)
WAN Connection Type "Automatic IP", I guess a DHCP server is active on your switch AP (IPConfig; WAN & LAN)
If no DHCP from switch use "Static IP
IP: xxx.xxx.xxx.185
Netmask: 255.255.255.192
Gateway: xxx.xxx.xxx.129
DNS server xxx.xxx.xxx.129
LAN IP adress 192.168.1.1
Netmask 255.255.255.0
DHCP server NOT enabled
Assign static IP in range 192.168.1.x to workstation(s) connected to the Asus
check your switch / AP firewall / NAT settings!!, make sure access is granted to 192.168.1.x (UTP / UDP / ICMP) or create a DMZ for the asus
Disable all firewalls on the Asus
Make sure RADIO is enabled (Wireless; advanced)
Now Save and Restart
IF this works you can implement more secure settings step by step
Good Luck
Followed Your advice. But starting with System set up and AP mode did result in a limitation of what to change, for example WAN IP-addresses.
So I started with Factory default. Changed to AP-mode using Telnet and NVRAM ....... ClientMode=0.
From there I entered according to your info. (No, we don't have DHCP-server on switch).
I have done these settings before, BUT the new thing was to set DNS address to xxx.xxx.xxx.129 (=Gateway value). (Why, I asked)
Result:No luck.
And I didn't managed to get this:
In your switch routing table there should then be some entry like:
0.0.0.0 192.168.1.1 0.0.0.0 UG brx (G for Gateway)
Next step:
Changed to Station mode: NVRAM .... ClientMode=1.
Reboot.
Ooops, now the switch showed my IP-address (after 2 days with 0.0.0.0)
Ping from LAN ? WAN-IP OK.
Ooops! Ping to switch OK. Ping to ......... OK
Ping from WAN-PC to ASUS OK. Ping from Internet to ASUS OK
:D :D :D :D :D :D :D :D :D :D :D :D :D :D :D :D
I can reach ASUS web page from Internet, I can print from .....,
I can probably reach FTP from internet (need to reboot first), but since I am writing this on a PC connected to ASUS LAN I need to finalise this first.
Security comes next but since our PC's are well protected thats a minor issue.
Now to the great moment of thanking You, Brubber.
Finding the missing part ( DNS IP) was something I probably haven't thought about until ASUS stuff was on the dump.
Without Your help and understanding ...... (sounds like a speach on the Oscar gala).
THANKS !!!
Now to the great moment of thanking You, Brubber.
THANKS !!!
:) :) :) :) :)
And all the others that tried to help you I guess!!
Perhaps now is a good time to make a small donation to this forum (http://wl500g.info/showthread.php?t=937)
Wonder if the topic starter "Lord_Moebius" managed to get his stuff working.
DNS is Used to map names to IP addresses and vice versa. Domain Name Servers maintain central lists of domain name/IP addresses and map the domain names in your Internet requests to other servers on the Internet until the specified web site is found.
P.S. is the wl500g still for sale? :p :p :p
I'm new to the world of WiFi, so I didn't understand the full details in this post. Does anyone have a simple step by step or a Visio that has the settings included.
THanks
duwrt
Followed Your advice. But starting with System set up and AP mode did result in a limitation of what to change, for example WAN IP-addresses.
So I started with Factory default. Changed to AP-mode using Telnet and NVRAM ....... ClientMode=0.
From there I entered according to your info. (No, we don't have DHCP-server on switch).
I have done these settings before, BUT the new thing was to set DNS address to xxx.xxx.xxx.129 (=Gateway value). (Why, I asked)
Result:No luck.
And I didn't managed to get this:
In your switch routing table there should then be some entry like:
0.0.0.0 192.168.1.1 0.0.0.0 UG brx (G for Gateway)
Next step:
Changed to Station mode: NVRAM .... ClientMode=1.
Reboot.
Ooops, now the switch showed my IP-address (after 2 days with 0.0.0.0)
Ping from LAN ? WAN-IP OK.
Ooops! Ping to switch OK. Ping to ......... OK
Ping from WAN-PC to ASUS OK. Ping from Internet to ASUS OK
:D :D :D :D :D :D :D :D :D :D :D :D :D :D :D :D
I can reach ASUS web page from Internet, I can print from .....,
I can probably reach FTP from internet (need to reboot first), but since I am writing this on a PC connected to ASUS LAN I need to finalise this first.
Security comes next but since our PC's are well protected thats a minor issue.
Now to the great moment of thanking You, Brubber.
Finding the missing part ( DNS IP) was something I probably haven't thought about until ASUS stuff was on the dump.
Without Your help and understanding ...... (sounds like a speach on the Oscar gala).
THANKS !!!
A few questions about the advice below:
1-Are the addresses below chosen for a specific reason or arbitrary.. More directly, why change from the standard netmask
~~~~~~~~~~~~
IP: xxx.xxx.xxx.185
Netmask: 255.255.255.192
Gateway: xxx.xxx.xxx.129
DNS server xxx.xxx.xxx.129
~~~~~~~~~~~
2- Doesn't it cause an issue if both devices use 192.168.1.1 for their LAN addresses.
3- What do you set as the gateway for the 2nd device in a bridged setup. Should it look to it's own WAN IP or back to the 1st device.
WAN Connection Type "Automatic IP", I guess a DHCP server is active on your switch AP (IPConfig; WAN & LAN)
If no DHCP from switch use "Static IP
IP: xxx.xxx.xxx.185
Netmask: 255.255.255.192
Gateway: xxx.xxx.xxx.129
DNS server xxx.xxx.xxx.129
LAN IP adress 192.168.1.1
Netmask 255.255.255.0
DHCP server NOT enabled
Assign static IP in range 192.168.1.x to workstation(s) connected to the Asus
check your switch / AP firewall / NAT settings!!, make sure access is granted to 192.168.1.x (UTP / UDP / ICMP) or create a DMZ for the asus
A few questions about the advice below:
1-Are the addresses below chosen for a specific reason or arbitrary.. More directly, why change from the standard netmask
~~~~~~~~~~~~
IP: xxx.xxx.xxx.185
Netmask: 255.255.255.192
Gateway: xxx.xxx.xxx.129
DNS server xxx.xxx.xxx.129
~~~~~~~~~~~It's not arbitrary, however not relevant to your setup: This subnet is defined on the primary AP in his network. If you're using the WL-500g with default settings you would have 192.168.1.1; 255.255.255.0 and so on.
2- Doesn't it cause an issue if both devices use 192.168.1.1 for their LAN addresses.Yes it would cause a minor issue because it's on a different subnet, so some routing would be necessary.
3- What do you set as the gateway for the 2nd device in a bridged setup. Should it look to it's own WAN IP or back to the 1st device. :confused: Don't understand your question.
To learn some basic TCP/IP this link http://www.pku.edu.cn/academic/research/computer-center/tc/html/TC0400.html will certainly be helpful. It's easy reading and it will help you to understand what you're doing.
For some more advanced reading and a lot of handy network tools go to http://www.subnetonline.com
And an easy subnet calculator: http://jodies.de/ipcalc